GSM-Forum - Step by step manual how to repair KMVTU000LM-B503 in pictures.

Page 1 of 2

Show 50 post(s) from this thread on one page

GSM-Forum (https://forum.gsmhosting.com/vbb/)

- Easy-Jtag / Easy-Jtag Plus (https://forum.gsmhosting.com/vbb/f672/)

- - Step by step manual how to repair KMVTU000LM-B503 in pictures. (https://forum.gsmhosting.com/vbb/f672/step-step-manual-how-repair-kmvtu000lm-b503-pictures-1935679/)

blang

04-07-2015 14:11

Step by step manual how to repair KMVTU000LM-B503 in pictures.

3 Attachment(s)

*****SCRENSHOTS KMVTU000LM REPAIR*****

DEAD EMMC:

http://i.gyazo.com/c376f40b4a45303c755a103c10f0659a.gif

Connect TP to GND:

http://forum.gsmhosting.com/vbb/atta...hmentid=336465

LOG OF EMMC AFTER TP to GND:

http://i.gyazo.com/1e8c12ff8298c7bde26e7fb364de16ae.gif

REMOVE eMMC TP from GND ( Break Wire )
SELECT FIRMWARE UPDATE:

http://i.gyazo.com/f78cd2472019a1e676cfa5ba46438767.gif

CONFIRM EMMC PART NUMBER:

http://i.gyazo.com/74237abca6bbb67cb08f06efb8d2f4cf.png

FIRMWARE UPDATE DONE:

http://i.gyazo.com/6c353259a2d534abe3661bc50b8ed83d.gif

RECONNECT EMMC AND IDENTIFY

http://i.gyazo.com/3367889245ba988551ea0368218ba0d0.gif

TRY TO READ SOMETHING:

http://i.gyazo.com/3ad1752a5cec898ebdc639ab40682e09.gif

oktay50000

04-07-2015 14:19

where is tp??...........

blang

04-07-2015 14:21

Quote:

Originally Posted by oktay50000 (Post 10972113)

where is tp??...........

its not TP. its z3x magic TP :)

login to forum and you will see attached picture.

rajeshchiyyan

04-07-2015 14:31

Quote:

Originally Posted by oktay50000 (Post 10972113)

where is tp??...........

Here IS the MAGIC TP
http://forum.gsmhosting.com/vbb/atta...9&d=1428411307

cemalefendi

04-07-2015 14:45

Z3X EasyJtag Software ver. 1.9.0.5
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 1818031584A59CAF, ,FW Ver.: 01.52
CMD Pullup Level:2062 mV
CMD Active Level:2382 mV
eMMC Device Information
EMMC CID : 1501005654553030300C20138686416E
EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 04/2014 Rev.0xC
EMMC NAME: VTU000 , S/N: 538150534
EMMC NAME (HEX): 56545530303000
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: VTU000_ 538150534_20150302_1643.extcsd

later

repaired log:

Z3X EasyJtag Software ver. 1.9.0.5
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 1818031584A59CAF, ,FW Ver.: 01.52
CMD Pullup Level:2062 mV
CMD Active Level:2392 mV
eMMC Device Information
EMMC CID : 1501005654553030300C20138686416E
EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 04/2014 Rev.0xC
EMMC NAME: VTU000 , S/N: 538150534
EMMC NAME (HEX): 56545530303000
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
Backup saved: VTU000_ 538150534_20150302_1644.extcsd
Done.

alanic

04-07-2015 15:16

Verifying eMMC firmware fail: NO Error

please help sir..

log :
CMD Pullup Level:2145 mV
CMD Active Level:2578 mV
Setup firmware normal update mode, wait 2..30 sec...
Success!
Sending eMMC firmware...
Success!
Verifying eMMC firmware...
Verifying eMMC firmware fail: NO Error
Done.

vikboston

04-07-2015 15:58

Hi,

This error:
'Verifying eMMC firmware fail: NO Error'
happend because you didn't disconnect everything from eMMC (all lines : 1.8V, 2.8V, CLK, CMD, DAT0) before making short TP to GND !!!!
Some current leakege apply from CMD, CLK, DAT0 box lines and eMMC goto wrong state, when disconnect only 1.8/2.8V power lines.
eMMC wrong state cause 'Verifying eMMC firmware fail: NO Error'
No Error - means no communication error, only firmware update error occurs.

Disconnect everything from eMMC, make short TP to GND, plug eMMC power then remove TP to GND, plug into box, make sure that eMMC Identify 000000, start update firmware again. eMMC Update Firmware should be OK this time !!!!!!!!!

DON'T FORGET TO REMOVE TP TO GND CONNECTION BEFORE FIRMWARE UPDATE, BECAUSE WILL BE SAME ERROR: 'Verifying eMMC firmware fail: NO Error' !!!!!!!!!

Regards Viktor

freeman2001

04-07-2015 16:47

Quote:

Originally Posted by alanic (Post 10972234)

verifying emmc firmware fail: No error

please help sir..

Log :
cmd pullup level:2145 mv
cmd active level:2578 mv
setup firmware normal update mode, wait 2..30 sec...
Success!
Sending emmc firmware...
Success!
Verifying emmc firmware...
Verifying emmc firmware fail: No error
done.

check your tp must be connected antil last operation

freeman2001

04-07-2015 16:51

CMD Active Level:2186 mV
Setup firmware normal update mode, wait 2..30 sec...
Success!
Sending eMMC firmware...
Success!
Verifying eMMC firmware...
Success!
Flashing eMMC firmware...
Success!
Repairing eMMC CID...
Success!
eMMC firmware is updated now!
Please reconnect eMMC power lines before next operation!
Please don't forget to repair extCSD from backup!
Please don't forget to configure BOOT sizes!
Done.

rePAIR DONE

CMD Pullup Level:752 mV
CMD Active Level:2186 mV
Input file : D:\Documents and Settings\freeman\My Documents\Downloads\i9300\EMMC_ROM2_00000000_00200 000.bin
Writing 0000200000 bytes to 00000000 ...ROM2 (BOOT1 ROM)
Done. Write Speed: 1017 kB/s

eMMC Device Information
EMMC CID : 15010056545530304DFC3D39868641FA
EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 04/2014 Rev.0xFC
EMMC NAME: VTU00M , S/N: 1027180166
EMMC NAME (HEX): 56545530304D00
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: VTU00M_1027180166_20150302_1747.extcsd
Done.

ROM 1 OKI

CMD Pullup Level:752 mV
CMD Active Level:2186 mV
Input file : D:\Documents and Settings\freeman\My Documents\Downloads\i9300\EMMC_ROM2_00000000_00200 000.bin
Writing 0000200000 bytes to 00000000 ...ROM2 (BOOT1 ROM)
Done. Write Speed: 1017 kB/s

ROM 2 OKI

I9300 REPAIR DEAD EMMC VIA TP WITHOUT REMOVE EMMC IN SPAIN HEEEEEEEEEEH

abdelkader85

04-07-2015 18:32

Quote:

Originally Posted by freeman2001 (Post 10972402)

but how via tp and witout remove the emmc ????

how to connect tp to gnd witout remove the emmc

the tp is under the emmc

freeman2001

04-07-2015 18:49

The question of one million must be smart and from dreambox tp sony geniration lol

javsoft

04-07-2015 22:33

the z3x magic question , how to do tp?

shoaibrao

04-07-2015 22:38

Quote:

Originally Posted by freeman2001 (Post 10972567)

The question of one million must be smart and from dreambox tp sony geniration lol

But Bro DreamBox Sony TP On CPU
And Its Under The EMMC And EMMC Fully Glued
If You Dont Mind Will You Share Here The Answer Of One Million Ques ;)

gerferomb

04-08-2015 02:08

What cable we use to connect TP from box?

alwi wafa

04-08-2015 02:10

amazing....
good job broo...

..::AppleLinks::..

04-08-2015 06:03

so i think not 2 easy work...we will remove emmc chip to work with TP????

Dr.Dekra

04-08-2015 10:21

Quote:

z3x easyjtag software ver. 1.9.0.5
loading emmc addon firmware... Io: 2800 mv
box s/n: , ,fw ver.: 01.52
cmd pullup level:2155 mv
cmd active level:2670 mv
emmc device information
emmc cid : 1501003030303030305620110726589c
emmc csd : 902701320f5903fff6dbffef8a404022
emmc manufacturer id: 0015 , oem id: 0100
emmc date: 05/2005 rev.0x56
emmc name: 000000 , s/n: 537986854
emmc name (hex): 30303030303000
emmc rom1 (main user data) capacity: 16384 mb
emmc rom2 (boot partition 1) capacity: 512 kb
emmc rom3 (boot partition 2) capacity: 512 kb
emmc rpmb (replay protected memory block) capacity: 128 kb
emmc permanent write protection: No
emmc temporary write protection: No
extended csd rev 1.5 (mmc 4.41)
boot configuration [partition_config: 0x00] no boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , partition config [179]: 0x00.
Backup saved: 000000_ 537986854_20150303_1018.extcsd
done.

Running:samsung: Emmc firmware update...
Confirmed emmc part number: Kmvtu000lm
z3x easyjtag software ver. 1.9.0.5
loading emmc addon firmware... Io: 2800 mv
box s/n: , ,fw ver.: 01.52
cmd pullup level:2165 mv
cmd active level:2670 mv
setup firmware normal update mode, wait 2..30 sec...
Success!
Sending emmc firmware...
Success!
Verifying emmc firmware...
Success!
Flashing emmc firmware...
Success!
Repairing emmc cid...
Can't init device, reason: Ocr ready timeout error [emmc dead]
done.

what about this error ?

kococos

04-08-2015 10:50

Z3X EasyJtag Software ver. 1.9.0.5
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 0B01400EE56989F0, ,FW Ver.: 01.52
CMD Pullup Level:3269 mV
CMD Active Level:3135 mV
Can't init device, Reason: OCR Ready Timeout Error [EMMC DEAD]
Done.

Z3X EasyJtag Software ver. 1.9.0.5
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 0B01400EE56989F0, ,FW Ver.: 01.52
CMD Pullup Level:3279 mV
CMD Active Level:3135 mV
eMMC Device Information
EMMC CID : 1501003030303030305620110726589C
EMMC CSD : 902701320F5903FFF6DBFFEF8A404022
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2005 Rev.0x56
EMMC NAME: 000000 , S/N: 537986854
EMMC NAME (HEX): 30303030303000
EMMC ROM1 (Main User Data) Capacity: 16384 MB
EMMC ROM2 (Boot Partition 1) Capacity: 512 kB
EMMC ROM3 (Boot Partition 2) Capacity: 512 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: 000000_ 537986854_20150303_1640.extcsd
Done.

Running:SAMSUNG: eMMC firmware update...
Confirmed eMMC Part Number: KMVTU000LM-B503
Z3X EasyJtag Software ver. 1.9.0.5
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 0B01400EE56989F0, ,FW Ver.: 01.52
CMD Pullup Level:3279 mV
CMD Active Level:3124 mV
Setup firmware normal update mode, wait 2..30 sec...
Success!
Sending eMMC firmware...
Success!
Verifying eMMC firmware...
Success!
Flashing eMMC firmware...
Success!
Repairing eMMC CID...
Can't init device, Reason: CMD Timeout Error
Done.

Running:SAMSUNG: eMMC firmware update...
Confirmed eMMC Part Number: KMVTU000LM-B503
Z3X EasyJtag Software ver. 1.9.0.5
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 0B01400EE56989F0, ,FW Ver.: 01.52
CMD Pullup Level:3279 mV
CMD Active Level:3135 mV
Setup firmware normal update mode, wait 2..30 sec...
Success!
Sending eMMC firmware...
Success!
Verifying eMMC firmware...
Success!
Flashing eMMC firmware...
Success!
Repairing eMMC CID...
Success!
eMMC firmware is updated now!
Please reconnect eMMC power lines before next operation!
Please don't forget to repair extCSD from backup!
Please don't forget to configure BOOT sizes!
Done.

Nice update...:)

vikboston

04-08-2015 10:57

Quote:

Originally Posted by Dr.Dekra (Post 10973718)

what about this error ?

"setup firmware normal update mode, wait 2..30 sec...
Success!
Sending emmc firmware...
Success!
Verifying emmc firmware...
Success!
Flashing emmc firmware...
Success!
Repairing emmc cid...
Can't init device, reason: Ocr ready timeout error [emmc dead]
done."

Hi,

"This solution can repair 90% dead KMVTU000LM-B503 eMMC"

This error means that eMMC can not be repaired only with
firmware update. Probably eMMC internal block mapping area damaged
or eMMC hw fail.

Best Regards

Dr.Dekra

04-08-2015 11:11

Quote:

Originally Posted by dr.dekra (Post 10973718)

what about this error ?

my problem solved

Quote:

can't init device, reason: Ocr ready timeout error [emmc dead]
done.

Running:samsung: Emmc firmware update...
Can't init device, reason: Ocr ready timeout error [emmc dead]
done.

Z3x easyjtag software ver. 1.9.0.5
loading emmc addon firmware... Io: 3300 mv
box s/n: 07ffd00b044beaae, ,fw ver.: 01.52
cmd pullup level:2155 mv
cmd active level:2681 mv
emmc device information
emmc cid : 1501003030303030305620110726589c
emmc csd : 902701320f5903fff6dbffef8a404022
emmc manufacturer id: 0015 , oem id: 0100
emmc date: 05/2005 rev.0x56
emmc name: 000000 , s/n: 537986854
emmc name (hex): 30303030303000
emmc rom1 (main user data) capacity: 16384 mb
emmc rom2 (boot partition 1) capacity: 512 kb
emmc rom3 (boot partition 2) capacity: 512 kb
emmc rpmb (replay protected memory block) capacity: 128 kb
emmc permanent write protection: No
emmc temporary write protection: No
extended csd rev 1.5 (mmc 4.41)
boot configuration [partition_config: 0x00] no boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , partition config [179]: 0x00.
Backup saved: 000000_ 537986854_20150303_1105.extcsd
done.

Running:samsung: Emmc firmware update...
Confirmed emmc part number: Kmvtu000lm-b503
z3x easyjtag software ver. 1.9.0.5
loading emmc addon firmware... Io: 3300 mv
box s/n: 07ffd00b044beaae, ,fw ver.: 01.52
cmd pullup level:2186 mv
cmd active level:3176 mv
setup firmware normal update mode, wait 2..30 sec...
Success!
Sending emmc firmware...
Success!
Verifying emmc firmware...
Verifying emmc firmware fail: No error
done.

Running:samsung: Emmc firmware update...
Confirmed emmc part number: Kmvtu000lm-b503
z3x easyjtag software ver. 1.9.0.5
loading emmc addon firmware... Io: 3300 mv
box s/n: 07ffd00b044beaae, ,fw ver.: 01.52
cmd pullup level:2175 mv
cmd active level:3196 mv
setup firmware normal update mode, wait 2..30 sec...
Success!
Sending emmc firmware...
Success!
Verifying emmc firmware...
Success!
Flashing emmc firmware...
Success!
Repairing emmc cid...
Success!
Emmc firmware is updated now!
Please reconnect emmc power lines before next operation!
Please don't forget to repair extcsd from backup!
Please don't forget to configure boot sizes!
Done.

Z3x easyjtag software ver. 1.9.0.5
loading emmc addon firmware... Io: 3300 mv
box s/n: 07ffd00b044beaae, ,fw ver.: 01.52
cmd pullup level:2175 mv
cmd active level:2805 mv
emmc device information
emmc cid : 15010056545530304dfc3d39868641fa
emmc csd : D02701320f5903fff6dbffff8e40406c
emmc manufacturer id: 0015 , oem id: 0100
emmc date: 04/2014 rev.0xfc
emmc name: Vtu00m , s/n: 1027180166
emmc name (hex): 56545530304d00
emmc rom1 (main user data) capacity: 15028 mb
emmc rom2 (boot partition 1) capacity: 2048 kb
emmc rom3 (boot partition 2) capacity: 2048 kb
emmc rpmb (replay protected memory block) capacity: 128 kb
emmc permanent write protection: No
emmc temporary write protection: No
extended csd rev 1.6 (mmc 4.5)
boot configuration [partition_config: 0x00] no boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , partition config [179]: 0x00.
Backup saved: Vtu00m_1027180166_20150303_1108.extcsd
done.

i just select 3.3volt in emmc voltage

thanks for this real solution

Edocomsel

04-08-2015 11:33

Please support this type of EMMC:

Code:

Z3X EasyJtag Software ver. 1.9.0.5

Loading eMMC Addon Firmware... IO: 2800 mV

Box S/N: 0606171217xxxxxx, ,FW Ver.: 01.52

CMD Pullup Level:2691 mV

CMD Active Level:2763 mV

Can't init device, Reason: OCR Ready Timeout Error [EMMC DEAD] 

Done.
 

Z3X EasyJtag Software ver. 1.9.0.5

Loading eMMC Addon Firmware... IO: 2800 mV

Box S/N: 0606171217xxxxxx, ,FW Ver.: 01.52

CMD Pullup Level:2681 mV

CMD Active Level:2732 mV

eMMC Device Information

EMMC CID : 1501003030303030305620110726589C
 

EMMC CSD : 902701320F5903FFF6DBFFEF8A404022
 

EMMC Manufacturer ID: 0015 , OEM ID: 0100

EMMC Date: 05/2005  Rev.0x56

EMMC NAME: 000000 , S/N:  537986854

EMMC NAME (HEX): 30303030303000 

EMMC ROM1 (Main User Data)   Capacity: 4095 MB

EMMC ROM2 (Boot Partition 1) Capacity: 512 kB

EMMC ROM3 (Boot Partition 2) Capacity: 512 kB

EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB

EMMC Permanent Write Protection: No

EMMC Temporary Write Protection: No

  Extended CSD rev 1.5 (MMC 4.41)
 

Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.

Boot bus config [177]: 0x00 , width 1bit  , Partition config [179]: 0x00.

Backup saved: 000000_ 537986854_20150303_1714.extcsd

Searching for partition tables...

Read Pages Failed, Reason: CMD Timeout Error 

Partitioning not detected...

Done.
 
 

Z3X EasyJtag Software ver. 1.9.0.5

Loading eMMC Addon Firmware... IO: 2800 mV

Box S/N: 0606171217xxxxxx, ,FW Ver.: 01.52

CMD Pullup Level:2072 mV

CMD Active Level:2155 mV

eMMC Device Information

EMMC CID : 15010053355530304D0203438A74C0F0

EMMC CSD : D02701320F5903FFF6DBFFE18E404028

EMMC Manufacturer ID: 0015 , OEM ID: 0100

EMMC Date: 12/2013 Rev.0x2

EMMC NAME: S5U00M , S/N: 54758004

EMMC NAME (HEX): 53355530304D00 

EMMC ROM1 (Main User Data) Capacity: 3728 MB

EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB

EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB

EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB

EMMC Permanent Write Protection: No

EMMC Temporary Write Protection: No

Extended CSD rev 1.5 (MMC 4.41)

Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.

Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.

Backup saved: S5U00M_ 54758004_20150303_1729.extcsd

Done.
 

Running:SAMSUNG: eMMC firmware update...

EMMC NAME: S5U00M

This eMMC is not supported yet!

To force eMMC Firmware Update:

* Press and keep 'Shift' key

* Start 'SAMSUNG: eMMC Firmware Update'

* Type and press 'Confirm' eMMC Part Number

eMMC can be fully damaged, if type non-original Part Number!

Dr.Dekra

04-09-2015 19:13

you are the best team ...maybe it's 100% :eek:

Code:

Z3X EasyJtag Software ver. 1.9.0.5

Loading eMMC Addon Firmware... IO: 2800 mV

Box S/N: 07FFD00B044BEAAE, ,FW Ver.: 01.52

CMD Pullup Level:2175 mV

CMD Active Level:2815 mV

Can't init device, Reason: OCR Ready Timeout Error [EMMC DEAD] 

Done.
 

Z3X EasyJtag Software ver. 1.9.0.5

Loading eMMC Addon Firmware... IO: 3300 mV

Box S/N: 07FFD00B044BEAAE, ,FW Ver.: 01.52

CMD Pullup Level:2165 mV

CMD Active Level:2670 mV

eMMC Device Information

EMMC CID : 1501003030303030305620110726589C

EMMC CSD : 902701320F5903FFF6DBFFEF8A404022

EMMC Manufacturer ID: 0015 , OEM ID: 0100

EMMC Date: 05/2005 Rev.0x56

EMMC NAME: 000000 , S/N: 537986854

EMMC NAME (HEX): 30303030303000 

EMMC ROM1 (Main User Data) Capacity: 16384 MB

EMMC ROM2 (Boot Partition 1) Capacity: 512 kB

EMMC ROM3 (Boot Partition 2) Capacity: 512 kB

EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB

EMMC Permanent Write Protection: No

EMMC Temporary Write Protection: No

Extended CSD rev 1.5 (MMC 4.41)

Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.

Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.

Backup saved: 000000_ 537986854_20150304_1905.extcsd

Done.
 

Running:SAMSUNG: eMMC firmware update...

Confirmed eMMC Part Number: KMVTU000LM-B503

Z3X EasyJtag Software ver. 1.9.0.5

Loading eMMC Addon Firmware... IO: 3300 mV

Box S/N: 07FFD00B044BEAAE, ,FW Ver.: 01.52

CMD Pullup Level:2186 mV

CMD Active Level:3207 mV

Setup firmware normal update mode, wait 2..30 sec... 

Success!

Sending eMMC firmware...

Success!

Verifying eMMC firmware...

Success!

Flashing eMMC firmware...

Success!

Repairing eMMC CID...

Success!

eMMC firmware is updated now! 

Please reconnect eMMC power lines before next operation!

Please don't forget to repair extCSD from backup!

Please don't forget to configure BOOT sizes!

Done.
 

Z3X EasyJtag Software ver. 1.9.0.5

Loading eMMC Addon Firmware... IO: 3300 mV

Box S/N: 07FFD00B044BEAAE, ,FW Ver.: 01.52

CMD Pullup Level:2175 mV

CMD Active Level:2805 mV

eMMC Device Information

EMMC CID : 15010056545530304DFC3D39868641FA

EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C

EMMC Manufacturer ID: 0015 , OEM ID: 0100

EMMC Date: 04/2014 Rev.0xFC

EMMC NAME: VTU00M , S/N: 1027180166

EMMC NAME (HEX): 56545530304D00 

EMMC ROM1 (Main User Data) Capacity: 15028 MB

EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB

EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB

EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB

EMMC Permanent Write Protection: No

EMMC Temporary Write Protection: No

Extended CSD rev 1.6 (MMC 4.5)

Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.

Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.

Backup saved: VTU00M_1027180166_20150304_1908.extcsd

Done.

secand phone is ok :)
this vtu from n7100

mobifone

04-10-2015 06:26

kindly can somebody post video tutorial from test point to software repair step by step .

dompo

04-10-2015 12:55

Klm8g2ff3b-b001 not suport .....

DJ Morgan

04-17-2015 13:25

Done - probably first phone in Poland repaired without removing eMMC chip;)
Just use very thin rounded injection needle.

Code:

Z3X EasyJtag Software ver. 1.9.0.5

Loading eMMC Addon Firmware... IO: 2800 mV

Box S/N: 1300300A9980D735, ,FW Ver.: 01.52

CMD Pullup Level:2083 mV

CMD Active Level:2536 mV

eMMC Device Information

EMMC CID : 1501003030303030305620110726589C

EMMC CSD : 902701320F5903FFF6DBFFEF8A404022

EMMC Manufacturer ID: 0015 , OEM ID: 0100

EMMC Date: 05/2005 Rev.0x56

EMMC NAME: 000000 , S/N: 537986854

EMMC NAME (HEX): 30303030303000 

EMMC ROM1 (Main User Data) Capacity: 16384 MB

EMMC ROM2 (Boot Partition 1) Capacity: 512 kB

EMMC ROM3 (Boot Partition 2) Capacity: 512 kB

EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB

EMMC Permanent Write Protection: No

EMMC Temporary Write Protection: No

Extended CSD rev 1.5 (MMC 4.41)

Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.

Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.

Backup saved: 000000_ 537986854_20150305_1352.extcsd

Done.
 

Running:SAMSUNG: eMMC firmware update...

Confirmed eMMC Part Number: KMVTU000LM-B503

Z3X EasyJtag Software ver. 1.9.0.5

Loading eMMC Addon Firmware... IO: 2800 mV

Box S/N: 1300300A9980D735, ,FW Ver.: 01.52

CMD Pullup Level:2072 mV

CMD Active Level:2547 mV

Setup firmware normal update mode, wait 2..30 sec... 

Success!

Sending eMMC firmware...

Success!

Verifying eMMC firmware...

Success!

Flashing eMMC firmware...

Success!

Repairing eMMC CID...

Success!

eMMC firmware is updated now! 

Please reconnect eMMC power lines before next operation!

Please don't forget to repair extCSD from backup!

Please don't forget to configure BOOT sizes!

Done.

yalamandareddy

04-21-2015 10:13

yahooo. i am from india repair done 2 s3 and one note 2 , with out remove emmc . thanks to blang .now must needed box z3x jtag for every one.

rathbone

04-21-2015 15:55

To Mr. Blang,

i have a question for you after we finish reviving our dead emmc.

" eMMC firmware is updated now!
Please reconnect all eMMC lines before next operation!
Please don't forget to repair extCSD from backup!
Please don't forget to configure BOOT sizes!"

how do you configure BOOT sizes on the following eMMC?

-- S3
--Note II
etc.....

can you please show us or teach us the correct values and how do we perform it using our easy jtag program.

thank you very much and i am waiting for your reply.

yalamandareddy

04-22-2015 07:33

Quote:

Originally Posted by rathbone (Post 11000763)

see there . special i9300/n7100 boot config button . just press that tab to config boot .

unlock in nepal

04-22-2015 08:16

Quote:

Originally Posted by blang (Post 10972089)

Fore This work we nead to remove emmc ic or any spacel tp point in pcb

yalamandareddy

04-22-2015 11:09

bro . make sharp needle and connect to pin .

smarvest

04-23-2015 13:27

DJ Morgan, can you please show us how to do it with picture shots? Thank you.

unlock in nepal

04-23-2015 17:02

FIRMWARE UPDATE ok writing error

Z3X EasyJtag Software ver. 1.9.1.2
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 191911044D64DB2C, ,FW Ver.: 01.52
CMD Pullup Level:2052 mV
CMD Active Level:2629 mV
eMMC Device Information
EMMC CID : 1501003030303030305620110726589C
EMMC CSD : 902701320F5903FFF6DBFFEF8A404022
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2005 Rev.0x56
EMMC NAME: 000000 , S/N: 537986854
EMMC NAME (HEX): 30303030303000
EMMC ROM1 (Main User Data) Capacity: 16384 MB
EMMC ROM2 (Boot Partition 1) Capacity: 512 kB
EMMC ROM3 (Boot Partition 2) Capacity: 512 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: 000000_ 537986854_20150304_2118.extcsd
Done.

eMMC firmware update

Running:SAMSUNG: eMMC firmware update...
Confirmed eMMC Part Number: KMVTU000LM-B503
Z3X EasyJtag Software ver. 1.9.1.2
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 191911044D64DB2C, ,FW Ver.: 01.52
CMD Pullup Level:2052 mV
CMD Active Level:2619 mV
Setup firmware update mode, wait 2..30 sec...
Success!
Sending eMMC firmware...
Success!
Verifying eMMC firmware...
Success!
Flashing eMMC firmware...
Success!
Repairing eMMC CID...
Success!
eMMC firmware is updated now!
Please reconnect all eMMC lines before next operation!
Please don't forget to repair extCSD from backup!
Please don't forget to configure BOOT sizes!
Done.

Rading ok

Z3X EasyJtag Software ver. 1.9.1.2
Skip loading eMMC Addon Firmware
CMD Pullup Level:2031 mV
CMD Active Level:2382 mV
Output file :C:\Documents and Settings\Narayanmobile\My Documents\EMMC_ROM1_00000000_20000000.bin
Reading 0x000020000000 bytes from 0x000000000000 ...ROM1 ( USER ROM)
Done. Read Speed: 637 kB/s

writing error

Input file : C:\Documents and Settings\Narayanmobile\Desktop\I9300 Fromsupport\EMMC_ROM1_00000000_20000000.bin
Writing 0020000000 bytes to 00000000 ...ROM1 (USER ROM)
Retry writing adress 0x00000000 (Attempt #1)...
Retry Success! Disabling Write Optimistations...
Retry writing adress 0x00003E00 (Attempt #1)...
Retry Success! Disabling Write Optimistations...
Retry writing adress 0x00007C00 (Attempt #1)...
Retry Success! Disabling Write Optimistations...
Retry writing adress 0x0000BA00 (Attempt #1)...
Retry Success! Disabling Write Optimistations...
Retry writing adress 0x0000F800 (Attempt #1)...
Retry Success! Disabling Write Optimistations...
Retry writing adress 0x00011E00 (Attempt #1)...
Retry Success! Disabling Write Optimistations...
Retry writing adress 0x00013E00 (Attempt #1)...
Retry Fail!
Retry writing adress 0x00013E00 (Attempt #2)...
Retry Fail!
Retry writing adress 0x00013E00 (Attempt #3)...
Retry Fail!
Write Block Failed, Reason: CARD Ready Timeout Error
Done.

Emmc info

eMMC Device Information
EMMC CID : 15010056545530304DFC3D39868641FA
EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 04/2014 Rev.0xFC
EMMC NAME: VTU00M , S/N: 1027180166
EMMC NAME (HEX): 56545530304D00
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: VTU00M_1027180166_20150304_2149.extcsd
Done.

unlock in nepal

04-23-2015 17:04

Quote:

Originally Posted by yalamandareddy (Post 11002688)

bro . make sharp needle and connect to pin .

Fore this remmove emmc ic

Nizda Mobile

04-23-2015 17:13

Quote:

Originally Posted by unlock in nepal (Post 11006375)

set boot partition............

BR
Nizda Mobile

unlock in nepal

04-24-2015 05:46

set boot partition............

BR
Nizda Mobile

How to sate boot partiton

Nizda Mobile

04-24-2015 11:18

Quote:

Originally Posted by unlock in nepal (Post 11007243)

set boot partition............

BR
Nizda Mobile

How to sate boot partiton

http://i61.tinypic.com/1z2dcsl.png

_MoHaMaD_

04-29-2015 09:30

_MoHaMaD_

04-29-2015 10:17

Running:SAMSUNG: eMMC firmware update...
Confirmed eMMC Part Number: KMVTU000LM
Z3X EasyJtag Software ver. 1.9.1.0
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 0303FF1EE5A6F6B4, ,FW Ver.: 01.52
CMD Pullup Level:1258 mV
CMD Active Level:2650 mV
Setup firmware update mode, wait 2..30 sec...
Success!
Sending eMMC firmware...
Success!
Verifying eMMC firmware...
Success!
Flashing eMMC firmware...
Success!
Repairing eMMC CID...
Can't init device, Reason: CMD Timeout Error
Done.

Z3X EasyJtag Software ver. 1.9.1.0
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 0303FF1EE5A6F6B4, ,FW Ver.: 01.52
CMD Pullup Level:1227 mV
CMD Active Level:2650 mV
Can't init device, Reason: CMD Timeout Error
Done.

DJ Morgan

05-14-2015 17:43

3 Attachment(s)

Quote:

Originally Posted by smarvest (Post 11005787)

DJ Morgan, can you please show us how to do it with picture shots? Thank you.

Just make your own adapter, working perfect if profilled correctly ;)

gjalvarez

05-30-2015 21:49

cAN ANYONE GIVE ME A HAND?

Hi everyone, I am trying to fix a I9300, it has a white lcd when I try to turn it on, I can access download mode normally, I coonect 6 cables to pcb according to the pictures on z3x server. after that I am using EMMC adaptor, I plug the cable to a phone charger 5 V, and When I try to detect EMMC y get this message:

Z3X EasyJtag Software ver. 2.0.0.2
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 1717160E617F118E, ,FW Ver.: 01.52
CMD Pullup Level:3114 mV
CMD Active Level:3196 mV
Can't init device, Reason: CMD Timeout Error
Done.

Whitout care the Voltage I select is always same answer, If I press Set i9300/i7100 Config

Running:Change BOOT CONFIG...
Z3X EasyJtag Software ver. 2.0.0.2
Skip loading eMMC Addon Firmware
CMD Pullup Level:1753 mV
CMD Active Level:1815 mV
Can't init device, Reason: CMD Timeout Error
Done.

Running:Change BOOT WIDTH...
Z3X EasyJtag Software ver. 2.0.0.2
Skip loading eMMC Addon Firmware
CMD Pullup Level:1753 mV
CMD Active Level:1815 mV
Can't init device, Reason: CMD Timeout Error
Done.

sumatera

06-06-2015 14:41

please ADD firmware emmc samsung KMK5U000VM-B309
for Gt-s7270

Z3X EasyJtag Software ver. 2.0.0.0
Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N: 07070xxxxxxxxx, ,FW Ver.: 01.52
CMD Pullup Level:2145 mV
CMD Active Level:3104 mV
eMMC Device Information
EMMC CID : 1501003030303030305620110726589C

EMMC CSD : 902701320F5903FFF6DBFFEF8A404022

EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2005 Rev.0x56
EMMC NAME: <b>000000</b> , S/N: 537986854
EMMC NAME (HEX): 30303030303000
EMMC ROM1 (Main User Data) Capacity: 4095 MB
EMMC ROM2 (Boot Partition 1) Capacity: 512 kB
EMMC ROM3 (Boot Partition 2) Capacity: 512 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.5 (MMC 4.41)

Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: 000000_ 537986854_20150505_1826.extcsd
Done.

BR

don_paolo

06-17-2015 05:45

Hi all,

Any chance we can set the Firmware update to not re-initialize the eMMC chip.?

In order to preserve customer / client data?

Thanks in advance.

Paolo

>>PakFones<<

09-01-2015 07:56

Samsung i9300 totally dead EMMC repair done without removing EMMC

Hi, friends here i am going to share Samsung i9300 totally dead EMMC [KMVTU000LM-B503] repair info how i have done this without removing EMMC from board. its not easy and also not possible without special devices. its just information if you have any emmc repair device you can get much information from this post. if you have dead phone in hands and have not any professional tool you can visit our service Lab to fix that.

What we need to do this.

1= Z3X Easy Jtag
2= i9300 with dead emmc
3= special needle [shown in picture]
4= Good soldering skills

[IMG]http://3.bp.********.com/-XQjOHh_Kmmk/VeSqW2H9tpI/AAAAAAAAJsI/pUnqN3KBABA/s640/i9300%2BEMMC%2Brepair%2Btotaly%2Bdead.png[/IMG]

Let's start get i9300 direct emmc pinouts from support. and remove glue under emmc near TP

Solder pinouts carefully on board and emmc adapter witch come with x3x jtag insert needle and try then connect emmc adapter to easy jtag box. then try to detect emmc when you see emmc detected log in lo window you can remove needle. then start formware upgrade and follow instruction carefully given in easy jtag box log window.

some screenshots.

[IMG]http://3.bp.********.com/-eqitXqNiFik/VeSuatjPjzI/AAAAAAAAJsU/Ha4flR-20tk/s640/1.bmp[/IMG]

[IMG]http://3.bp.********.com/-nyi2WyxQ4f0/VeSu1mQLx5I/AAAAAAAAJsk/GRsw9_B8iJg/s640/2.bmp[/IMG]

[IMG]http://4.bp.********.com/-d6KjQIzByRU/VeSvC8e9QSI/AAAAAAAAJss/fyPTANRav6A/s640/4.bmp[/IMG]

Complete Log

Code:

Success! Sending eMMC firmware... Success! Verifying eMMC firmware... Success! Flashing eMMC firmware... Success! Repairing eMMC CID... Success! eMMC firmware is updated now! Please reconnect all eMMC lines before next operation! Please don't forget to repair extCSD from backup! Please don't forget to configure BOOT sizes! Done. extCSD file...C:\Program Files\Z3X\EASYJTAG\Backups\000000_ 537986854_20150602_1959.extcsd Running:Repair extCSD... Z3X EasyJtag Software ver. 2.0.3.0 Skip loading eMMC Addon Firmware CMD Pullup Level:742 mV CMD Active Level:2186 mV Writing... Done. Z3X EasyJtag Software ver. 2.0.3.0 Loading eMMC Addon Firmware... IO: 2800 mV Box S/N: xxxxxxxxxxxx, ,FW Ver.: 01.52 CMD Pullup Level:742 mV CMD Active Level:2196 mV eMMC Device Information EMMC CID : 15010056545530304DFC3D39868641FA EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C EMMC Manufacturer ID: 0015 , OEM ID: 0100 EMMC Date: 04/2014 Rev.0xFC EMMC NAME: VTU00M , S/N: 1027180166 EMMC NAME (HEX): 56545530304D00 EMMC ROM1 (Main User Data) Capacity: 15028 MB EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD rev 1.6 (MMC 4.5) Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured. Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00. Backup saved: VTU00M_1027180166_20150602_2001.extcsd Done. Running:Change BOOT CONFIG... Z3X EasyJtag Software ver. 2.0.3.0 Skip loading eMMC Addon Firmware CMD Pullup Level:742 mV CMD Active Level:2196 mV Writing eMMC Register... Written: REG : 179 VAL :48 Done. Running:Change BOOT WIDTH... Z3X EasyJtag Software ver. 2.0.3.0 Skip loading eMMC Addon Firmware CMD Pullup Level:742 mV CMD Active Level:2196 mV Writing eMMC Register... Written: REG : 177 VAL :1 Done. Z3X EasyJtag Software ver. 2.0.3.0 Loading eMMC Addon Firmware... IO: 2800 mV Box S/N: xxxxxxxxxxx, ,FW Ver.: 01.52 CMD Pullup Level:742 mV CMD Active Level:2196 mV eMMC Device Information EMMC CID : 15010056545530304DFC3D39868641FA EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C EMMC Manufacturer ID: 0015 , OEM ID: 0100 EMMC Date: 04/2014 Rev.0xFC EMMC NAME: VTU00M , S/N: 1027180166 EMMC NAME (HEX): 56545530304D00 EMMC ROM1 (Main User Data) Capacity: 15028 MB EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD rev 1.6 (MMC 4.5) Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1) Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48. Backup saved: VTU00M_1027180166_20150602_2002.extcsd Done. i9300\EMMC_ROM1_00000000_20000000.bin Writing 0020000000 bytes to 00000000 ...ROM1 (USER ROM) Done. Write Speed: 4800 kB/s Checking NAND Image : C:\Documents and Settings\ABDUL HAKEEM\Desktop\i9300 ec dead\dump i9300\EMMC_ROM2_00000000_00200000.bin File successefuly loaded! Processing file...C:\Documents and Settings\ABDUL HAKEEM\Desktop\i9300 ec dead\dump i9300\EMMC_ROM2_00000000_00200000.bin Z3X EasyJtag Software ver. 2.0.3.0 Skip loading eMMC Addon Firmware CMD Pullup Level:721 mV CMD Active Level:1134 mV Input file : C:\Documents and Settings\ABDUL HAKEEM\Desktop\i9300 ec dead\dump i9300\EMMC_ROM2_00000000_00200000.bin Writing 0000200000 bytes to 00000000 ...ROM2 (BOOT1 ROM) Done. Write Speed: 818 kB/s Z3X EasyJtag Software ver. 2.0.3.0 Skip loading eMMC Addon Firmware CMD Pullup Level:721 mV CMD Active Level:1134 mV Output file :C:\Documents and Settings\ABDUL HAKEEM\Desktop\i9300 ec dead\EMMC_ROM1_00000000_02000000.bin Reading 0x000002000000 bytes from 0x000000000000 ...ROM1 ( USER ROM) Done. Read Speed: 629 kB/s

Br,
PAK FONES

>>PakFones<<

09-01-2015 08:11

https://lh3.googleusercontent.com/-P...252520dead.png
https://lh3.googleusercontent.com/-d...640-Ic42/1.jpg
https://lh3.googleusercontent.com/-7...640-Ic42/2.jpg
https://lh3.googleusercontent.com/-V...640-Ic42/4.jpg

ahmc	09-01-2015 14:53

http://forum.gsmhosting.com/vbb/f258.../#post11237846

chand_gee

09-01-2015 15:03

already posted butt thanks for work hard
http://forum.gsmhosting.com/vbb/f609...tures-1945278/

911gsmcom

09-06-2015 07:30

amazing....:cool::cool::cool::cool:

>>PakFones<<

09-11-2015 12:49

Quote:

Originally Posted by chand_gee (Post 11260027)

already posted butt thanks for work hard
http://forum.gsmhosting.com/vbb/f609...tures-1945278/

i know sure i have get much information from your post.

anombase

09-16-2015 14:27

help me on how to connect tp

Quote:

Originally Posted by >>PakFones<< (Post 11259032)

pls sir can u help me with how to connect tp.thanks in advance

anombase

09-16-2015 16:07

Quote:

Originally Posted by blang (Post 10972089)

pls can u connect magic tp without removing EMMC?:confused::confused:

All times are GMT +1. The time now is 17:23.

Page 1 of 2

Show 50 post(s) from this thread on one page

Page generated in 0.48406 seconds with 6 queries

SEO by vBSEO