Acer Z205 emmc dead or not ?

[alamgir80]

30-Apr-21 11:06:43 AM> 
30-Apr-21 11:06:43 AM> eMMC_tool Suite  ver. 1.6.4.0 (release date: 30.12.2020)
30-Apr-21 11:06:46 AM> Microsoft Windows 10 (64 bit) build 16299 (10.0.16299.15)
30-Apr-21 11:06:46 AM> 
30-Apr-21 11:06:46 AM> Looking for EasyJTAG box...
30-Apr-21 11:06:46 AM> EasyJTAG API ver. 3403
30-Apr-21 11:06:46 AM> OpenUSB returned = 0
30-Apr-21 11:06:47 AM> EasyJTAG Box Serial = 0014D520AAB084B4
30-Apr-21 11:06:48 AM> Card Serial = AAC20012
30-Apr-21 11:06:48 AM> EasyJTAG Box Firmware = 2.5301
30-Apr-21 11:06:48 AM> 
30-Apr-21 11:13:35 AM> Looking for EasyJTAG box...
30-Apr-21 11:13:35 AM> EasyJTAG API ver. 3403
30-Apr-21 11:13:35 AM> Setting IO Levels to 1.8V
30-Apr-21 11:13:35 AM> Setting frequence to 36 MHz
30-Apr-21 11:13:35 AM> EasyJTAG Box Serial = 0014D520AAB084B4
30-Apr-21 11:13:35 AM> EasyJTAG Box Firmware = 2.5301
30-Apr-21 11:13:36 AM> Setting interface to EasyJtag2/ISP_HiPower
30-Apr-21 11:13:36 AM> Setting bus width to 4 Bit
30-Apr-21 11:13:36 AM> HiPower mode is ON
30-Apr-21 11:13:36 AM> Setting frequence to 36 MHz
30-Apr-21 11:13:36 AM> CMD Pullup Level: 1829 mV
30-Apr-21 11:13:36 AM> CMD Active Level: 1879 mV
30-Apr-21 11:13:37 AM> eMMC Init returned = 0
30-Apr-21 11:13:37 AM> EMMC Device Information :
30-Apr-21 11:13:37 AM> EMMC CID: 7001004D4D4330344758E3F1B92D9195
30-Apr-21 11:13:37 AM> EMMC CSD: D04F01320F5903FFFFFFFFE78A400051
30-Apr-21 11:13:37 AM> EMMC Manufacture : KINGSTONE , EMMC NAME: MMC04G , HEX: 4D4D43303447 , S/N: E3F1B92D , rev. 0x58
30-Apr-21 11:13:37 AM> EMMC Manufacture ID: 0x70 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 9/2014
30-Apr-21 11:13:37 AM>    EMMC ROM 1 (Main User Data) Capacity: 3688 MB (0000E6800000)
30-Apr-21 11:13:37 AM>    EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 2048 KB (000000200000)
30-Apr-21 11:13:37 AM>    EMMC RPMB (Replay Protected Memory Block) Capacity: 128 KB (000000020000) Counter: 0 , Response: Maybe not clean
30-Apr-21 11:13:37 AM> EMMC Permanent Write Protection: No
30-Apr-21 11:13:37 AM> EMMC Temporary Write Protection: No
30-Apr-21 11:13:37 AM> Extended CSD Information :
30-Apr-21 11:13:37 AM> Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
30-Apr-21 11:13:37 AM> Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
30-Apr-21 11:13:37 AM> Boot Bus Config: 0x00 , width 1bit
30-Apr-21 11:13:37 AM> H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
30-Apr-21 11:13:37 AM> Supported partition features [PARTITIONING_SUPPORT]: 0x07
30-Apr-21 11:13:37 AM> Device supports partitioning features
30-Apr-21 11:13:37 AM> Device can have enhanced technological features in partitions and user data area
30-Apr-21 11:13:37 AM> Device can have extended partitions attribute
30-Apr-21 11:13:37 AM> Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
30-Apr-21 11:13:37 AM> Backup saved: MMC04G_E3F1B92D_20210430_111337.extcsd
30-Apr-21 11:13:37 AM> EMMC Init completed.
30-Apr-21 11:13:37 AM> 
30-Apr-21 11:13:38 AM> Warning: BusWidth is automatically set to 1 Bit
30-Apr-21 11:13:38 AM> 
30-Apr-21 11:13:39 AM> Scanning soft partitions
30-Apr-21 11:13:45 AM> Partition table not found
30-Apr-21 11:13:45 AM> 
30-Apr-21 11:13:45 AM> Get firmware version
30-Apr-21 11:13:56 AM> 
30-Apr-21 11:14:07 AM> 
30-Apr-21 11:14:08 AM> Brand = acer
30-Apr-21 11:14:08 AM> Manufacturer = Acer
30-Apr-21 11:14:08 AM> Device = acer_z205p
30-Apr-21 11:14:08 AM> Model = Z205
30-Apr-21 11:14:08 AM> CPU Abi = armeabi-v7a
30-Apr-21 11:14:08 AM> Mediatek platform = MT6572
30-Apr-21 11:14:08 AM> Android release = 4.4.2
30-Apr-21 11:14:08 AM> Firmware version = Acer_AV0K0_Z205P_1.003.00_AAP_DIGIHID
30-Apr-21 11:14:08 AM> Firmware date = 2014? 09? 24? ??? 09:32:33 CST
30-Apr-21 11:14:20 AM> 
30-Apr-21 11:14:20 AM> Looking for EasyJTAG box...
30-Apr-21 11:14:20 AM> EasyJTAG API ver. 3403
30-Apr-21 11:14:20 AM> Setting IO Levels to 1.8V
30-Apr-21 11:14:20 AM> Setting frequence to 36 MHz
30-Apr-21 11:14:20 AM> EasyJTAG Box Serial = 0014D520AAB084B4
30-Apr-21 11:14:20 AM> EasyJTAG Box Firmware = 2.5301
30-Apr-21 11:14:22 AM> Setting interface to EasyJtag2/ISP_HiPower
30-Apr-21 11:14:22 AM> Setting bus width to 1 Bit
30-Apr-21 11:14:22 AM> HiPower mode is ON
30-Apr-21 11:14:22 AM> Setting frequence to 36 MHz
30-Apr-21 11:14:22 AM> CMD Pullup Level: 1829 mV
30-Apr-21 11:14:22 AM> CMD Active Level: 1879 mV
30-Apr-21 11:14:22 AM> eMMC Init returned = 0
30-Apr-21 11:14:22 AM> EMMC Device Information :
30-Apr-21 11:14:22 AM> EMMC CID: 7001004D4D4330344758E3F1B92D9195
30-Apr-21 11:14:22 AM> EMMC CSD: D04F01320F5903FFFFFFFFE78A400051
30-Apr-21 11:14:22 AM> EMMC Manufacture : KINGSTONE , EMMC NAME: MMC04G , HEX: 4D4D43303447 , S/N: E3F1B92D , rev. 0x58
30-Apr-21 11:14:22 AM> EMMC Manufacture ID: 0x70 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 9/2014
30-Apr-21 11:14:22 AM>    EMMC ROM 1 (Main User Data) Capacity: 3688 MB (0000E6800000)
30-Apr-21 11:14:22 AM>    EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 2048 KB (000000200000)
30-Apr-21 11:14:22 AM>    EMMC RPMB (Replay Protected Memory Block) Capacity: 128 KB (000000020000) Counter: 0 , Response: Clean
30-Apr-21 11:14:22 AM> EMMC Permanent Write Protection: No
30-Apr-21 11:14:22 AM> EMMC Temporary Write Protection: No
30-Apr-21 11:14:22 AM> Extended CSD Information :
30-Apr-21 11:14:22 AM> Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
30-Apr-21 11:14:22 AM> Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
30-Apr-21 11:14:22 AM> Boot Bus Config: 0x00 , width 1bit
30-Apr-21 11:14:22 AM> H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
30-Apr-21 11:14:22 AM> Supported partition features [PARTITIONING_SUPPORT]: 0x07
30-Apr-21 11:14:22 AM> Device supports partitioning features
30-Apr-21 11:14:22 AM> Device can have enhanced technological features in partitions and user data area
30-Apr-21 11:14:22 AM> Device can have extended partitions attribute
30-Apr-21 11:14:22 AM> Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
30-Apr-21 11:14:22 AM> Backup saved: MMC04G_E3F1B92D_20210430_111422.extcsd
30-Apr-21 11:14:22 AM> EMMC Init completed.
30-Apr-21 11:14:22 AM> 
30-Apr-21 11:14:22 AM> This operation is performed only for Samsung eMMC, Sandisk eMMC or EMMC 5.0 and higher
30-Apr-21 11:14:22 AM> 
30-Apr-21 11:15:00 AM> Looking for EasyJTAG box...
30-Apr-21 11:15:00 AM> EasyJTAG API ver. 3403
30-Apr-21 11:15:00 AM> Setting IO Levels to 1.8V
30-Apr-21 11:15:00 AM> Setting frequence to 36 MHz
30-Apr-21 11:15:00 AM> EasyJTAG Box Serial = 0014D520AAB084B4
30-Apr-21 11:15:00 AM> EasyJTAG Box Firmware = 2.5301
30-Apr-21 11:15:02 AM> Setting interface to EasyJtag2/ISP_HiPower
30-Apr-21 11:15:02 AM> Setting bus width to 1 Bit
30-Apr-21 11:15:02 AM> HiPower mode is ON
30-Apr-21 11:15:02 AM> Setting frequence to 36 MHz
30-Apr-21 11:15:02 AM> CMD Pullup Level: 1831 mV
30-Apr-21 11:15:02 AM> CMD Active Level: 1882 mV
30-Apr-21 11:15:02 AM> eMMC Init returned = 0
30-Apr-21 11:15:02 AM> EMMC Device Information :
30-Apr-21 11:15:02 AM> EMMC CID: 7001004D4D4330344758E3F1B92D9195
30-Apr-21 11:15:02 AM> EMMC CSD: D04F01320F5903FFFFFFFFE78A400051
30-Apr-21 11:15:02 AM> EMMC Manufacture : KINGSTONE , EMMC NAME: MMC04G , HEX: 4D4D43303447 , S/N: E3F1B92D , rev. 0x58
30-Apr-21 11:15:02 AM> EMMC Manufacture ID: 0x70 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 9/2014
30-Apr-21 11:15:02 AM>    EMMC ROM 1 (Main User Data) Capacity: 3688 MB (0000E6800000)
30-Apr-21 11:15:02 AM>    EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 2048 KB (000000200000)
30-Apr-21 11:15:02 AM>    EMMC RPMB (Replay Protected Memory Block) Capacity: 128 KB (000000020000) Counter: 0 , Response: Clean
30-Apr-21 11:15:02 AM> EMMC Permanent Write Protection: No
30-Apr-21 11:15:02 AM> EMMC Temporary Write Protection: No
30-Apr-21 11:15:02 AM> Extended CSD Information :
30-Apr-21 11:15:02 AM> Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
30-Apr-21 11:15:02 AM> Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
30-Apr-21 11:15:02 AM> Boot Bus Config: 0x00 , width 1bit
30-Apr-21 11:15:02 AM> H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
30-Apr-21 11:15:02 AM> Supported partition features [PARTITIONING_SUPPORT]: 0x07
30-Apr-21 11:15:02 AM> Device supports partitioning features
30-Apr-21 11:15:02 AM> Device can have enhanced technological features in partitions and user data area
30-Apr-21 11:15:02 AM> Device can have extended partitions attribute
30-Apr-21 11:15:02 AM> Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
30-Apr-21 11:15:02 AM> Backup saved: MMC04G_E3F1B92D_20210430_111502.extcsd
30-Apr-21 11:15:02 AM> EMMC Init completed.
30-Apr-21 11:15:02 AM> 
30-Apr-21 11:15:03 AM> Operation: Find table from emmc
30-Apr-21 11:15:03 AM> 
30-Apr-21 11:15:03 AM> Vendor: Mediatek
30-Apr-21 11:15:03 AM> Platform: MT6572
30-Apr-21 11:15:03 AM> Searching GPT ...
30-Apr-21 11:15:03 AM> GPT header is not found
30-Apr-21 11:15:03 AM> Searching PMT (MediaTek) ...
30-Apr-21 11:15:16 AM> PMT found at address 0x0000E6701000
30-Apr-21 11:15:16 AM> Searching MBR ...
30-Apr-21 11:15:16 AM> MBR found
30-Apr-21 11:15:16 AM> PMT successfully parsed
30-Apr-21 11:15:16 AM> 
30-Apr-21 11:15:46 AM> Looking for EasyJTAG box...
30-Apr-21 11:15:46 AM> EasyJTAG API ver. 3403
30-Apr-21 11:15:46 AM> Setting IO Levels to 1.8V
30-Apr-21 11:15:46 AM> Setting frequence to 36 MHz
30-Apr-21 11:15:46 AM> EasyJTAG Box Serial = 0014D520AAB084B4
30-Apr-21 11:15:46 AM> EasyJTAG Box Firmware = 2.5301
30-Apr-21 11:15:47 AM> Setting interface to EasyJtag2/ISP_HiPower
30-Apr-21 11:15:48 AM> Setting bus width to 1 Bit
30-Apr-21 11:15:48 AM> HiPower mode is ON
30-Apr-21 11:15:48 AM> Setting frequence to 36 MHz
30-Apr-21 11:15:48 AM> CMD Pullup Level: 1831 mV
30-Apr-21 11:15:48 AM> CMD Active Level: 1881 mV
30-Apr-21 11:15:48 AM> eMMC Init returned = 0
30-Apr-21 11:15:48 AM> EMMC Device Information :
30-Apr-21 11:15:48 AM> EMMC CID: 7001004D4D4330344758E3F1B92D9195
30-Apr-21 11:15:48 AM> EMMC CSD: D04F01320F5903FFFFFFFFE78A400051
30-Apr-21 11:15:48 AM> EMMC Manufacture : KINGSTONE , EMMC NAME: MMC04G , HEX: 4D4D43303447 , S/N: E3F1B92D , rev. 0x58
30-Apr-21 11:15:48 AM> EMMC Manufacture ID: 0x70 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 9/2014
30-Apr-21 11:15:48 AM>    EMMC ROM 1 (Main User Data) Capacity: 3688 MB (0000E6800000)
30-Apr-21 11:15:48 AM>    EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 2048 KB (000000200000)
30-Apr-21 11:15:48 AM>    EMMC RPMB (Replay Protected Memory Block) Capacity: 128 KB (000000020000) Counter: 0 , Response: Clean
30-Apr-21 11:15:48 AM> EMMC Permanent Write Protection: No
30-Apr-21 11:15:48 AM> EMMC Temporary Write Protection: No
30-Apr-21 11:15:48 AM> Extended CSD Information :
30-Apr-21 11:15:48 AM> Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
30-Apr-21 11:15:48 AM> Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
30-Apr-21 11:15:48 AM> Boot Bus Config: 0x00 , width 1bit
30-Apr-21 11:15:48 AM> H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
30-Apr-21 11:15:48 AM> Supported partition features [PARTITIONING_SUPPORT]: 0x07
30-Apr-21 11:15:48 AM> Device supports partitioning features
30-Apr-21 11:15:48 AM> Device can have enhanced technological features in partitions and user data area
30-Apr-21 11:15:48 AM> Device can have extended partitions attribute
30-Apr-21 11:15:48 AM> Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
30-Apr-21 11:15:48 AM> Backup saved: MMC04G_E3F1B92D_20210430_111548.extcsd
30-Apr-21 11:15:48 AM> EMMC Init completed.
30-Apr-21 11:15:48 AM> 
30-Apr-21 11:15:48 AM> Operation: Reading from eMMC...
30-Apr-21 11:15:48 AM> 
30-Apr-21 11:16:20 AM> Reading from: ROM1 , start: 0x000000000000 , size: 0x000003D40000
30-Apr-21 11:16:20 AM> Output file: P:\Mobile\Jtag\Acer\EMMC_MMC04G_ROM1_000000000000_000003D40000.bin
30-Apr-21 11:16:20 AM> eMMC switching to ROM1
30-Apr-21 11:16:21 AM> Reading partition...
30-Apr-21 11:16:39 AM> Done reading partition. Read speed: 3456.91 Kb/s
30-Apr-21 11:16:50 AM> 
30-Apr-21 11:17:01 AM> 
30-Apr-21 11:17:01 AM> All done   time: [00:00:41:071]
30-Apr-21 11:17:01 AM> 
30-Apr-21 11:17:20 AM> Looking for EasyJTAG box...
30-Apr-21 11:17:20 AM> EasyJTAG API ver. 3403
30-Apr-21 11:17:20 AM> Setting IO Levels to 1.8V
30-Apr-21 11:17:20 AM> Setting frequence to 36 MHz
30-Apr-21 11:17:20 AM> EasyJTAG Box Serial = 0014D520AAB084B4
30-Apr-21 11:17:20 AM> EasyJTAG Box Firmware = 2.5301
30-Apr-21 11:17:21 AM> Setting interface to EasyJtag2/ISP_HiPower
30-Apr-21 11:17:21 AM> Setting bus width to 1 Bit
30-Apr-21 11:17:21 AM> HiPower mode is ON
30-Apr-21 11:17:21 AM> Setting frequence to 36 MHz
30-Apr-21 11:17:21 AM> CMD Pullup Level: 1829 mV
30-Apr-21 11:17:21 AM> CMD Active Level: 1881 mV
30-Apr-21 11:17:22 AM> eMMC Init returned = 0
30-Apr-21 11:17:22 AM> EMMC Device Information :
30-Apr-21 11:17:22 AM> EMMC CID: 7001004D4D4330344758E3F1B92D9195
30-Apr-21 11:17:22 AM> EMMC CSD: D04F01320F5903FFFFFFFFE78A400051
30-Apr-21 11:17:22 AM> EMMC Manufacture : KINGSTONE , EMMC NAME: MMC04G , HEX: 4D4D43303447 , S/N: E3F1B92D , rev. 0x58
30-Apr-21 11:17:22 AM> EMMC Manufacture ID: 0x70 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 9/2014
30-Apr-21 11:17:22 AM>    EMMC ROM 1 (Main User Data) Capacity: 3688 MB (0000E6800000)
30-Apr-21 11:17:22 AM>    EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 2048 KB (000000200000)
30-Apr-21 11:17:22 AM>    EMMC RPMB (Replay Protected Memory Block) Capacity: 128 KB (000000020000) Counter: 0 , Response: Clean
30-Apr-21 11:17:22 AM> EMMC Permanent Write Protection: No
30-Apr-21 11:17:22 AM> EMMC Temporary Write Protection: No
30-Apr-21 11:17:22 AM> Extended CSD Information :
30-Apr-21 11:17:22 AM> Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
30-Apr-21 11:17:22 AM> Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
30-Apr-21 11:17:22 AM> Boot Bus Config: 0x00 , width 1bit
30-Apr-21 11:17:22 AM> H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
30-Apr-21 11:17:22 AM> Supported partition features [PARTITIONING_SUPPORT]: 0x07
30-Apr-21 11:17:22 AM> Device supports partitioning features
30-Apr-21 11:17:22 AM> Device can have enhanced technological features in partitions and user data area
30-Apr-21 11:17:22 AM> Device can have extended partitions attribute
30-Apr-21 11:17:22 AM> Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
30-Apr-21 11:17:22 AM> Backup saved: MMC04G_E3F1B92D_20210430_111722.extcsd
30-Apr-21 11:17:22 AM> EMMC Init completed.
30-Apr-21 11:17:22 AM> 
30-Apr-21 11:17:22 AM> Operation: Reading from eMMC...
30-Apr-21 11:17:22 AM> 
30-Apr-21 11:17:26 AM> Reading from: ROM2 , start: 0x000000000000 , size: 0x000000200000
30-Apr-21 11:17:26 AM> Output file: P:\Mobile\Jtag\Acer\EMMC_MMC04G_ROM2_000000000000_000000200000.bin
30-Apr-21 11:17:26 AM> eMMC switching to ROM2
30-Apr-21 11:17:26 AM> Reading partition...
30-Apr-21 11:17:27 AM> Done reading partition. Read speed: 2562.47 Kb/s
30-Apr-21 11:17:38 AM> 
30-Apr-21 11:17:49 AM> 
30-Apr-21 11:17:49 AM> All done   time: [00:00:23:611]
30-Apr-21 11:17:49 AM> 
30-Apr-21 11:17:57 AM> Looking for EasyJTAG box...
30-Apr-21 11:17:57 AM> EasyJTAG API ver. 3403
30-Apr-21 11:17:57 AM> Setting IO Levels to 1.8V
30-Apr-21 11:17:57 AM> Setting frequence to 36 MHz
30-Apr-21 11:17:57 AM> EasyJTAG Box Serial = 0014D520AAB084B4
30-Apr-21 11:17:57 AM> EasyJTAG Box Firmware = 2.5301
30-Apr-21 11:17:59 AM> Setting interface to EasyJtag2/ISP_HiPower
30-Apr-21 11:17:59 AM> Setting bus width to 1 Bit
30-Apr-21 11:17:59 AM> HiPower mode is ON
30-Apr-21 11:17:59 AM> Setting frequence to 36 MHz
30-Apr-21 11:17:59 AM> CMD Pullup Level: 1828 mV
30-Apr-21 11:17:59 AM> CMD Active Level: 1881 mV
30-Apr-21 11:17:59 AM> eMMC Init returned = 0
30-Apr-21 11:17:59 AM> EMMC Device Information :
30-Apr-21 11:17:59 AM> EMMC CID: 7001004D4D4330344758E3F1B92D9195
30-Apr-21 11:17:59 AM> EMMC CSD: D04F01320F5903FFFFFFFFE78A400051
30-Apr-21 11:17:59 AM> EMMC Manufacture : KINGSTONE , EMMC NAME: MMC04G , HEX: 4D4D43303447 , S/N: E3F1B92D , rev. 0x58
30-Apr-21 11:17:59 AM> EMMC Manufacture ID: 0x70 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 9/2014
30-Apr-21 11:18:00 AM>    EMMC ROM 1 (Main User Data) Capacity: 3688 MB (0000E6800000)
30-Apr-21 11:18:00 AM>    EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 2048 KB (000000200000)
30-Apr-21 11:18:00 AM>    EMMC RPMB (Replay Protected Memory Block) Capacity: 128 KB (000000020000) Counter: 0 , Response: Clean
30-Apr-21 11:18:00 AM> EMMC Permanent Write Protection: No
30-Apr-21 11:18:00 AM> EMMC Temporary Write Protection: No
30-Apr-21 11:18:00 AM> Extended CSD Information :
30-Apr-21 11:18:00 AM> Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
30-Apr-21 11:18:00 AM> Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
30-Apr-21 11:18:00 AM> Boot Bus Config: 0x00 , width 1bit
30-Apr-21 11:18:00 AM> H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
30-Apr-21 11:18:00 AM> Supported partition features [PARTITIONING_SUPPORT]: 0x07
30-Apr-21 11:18:00 AM> Device supports partitioning features
30-Apr-21 11:18:00 AM> Device can have enhanced technological features in partitions and user data area
30-Apr-21 11:18:00 AM> Device can have extended partitions attribute
30-Apr-21 11:18:00 AM> Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
30-Apr-21 11:18:00 AM> Backup saved: MMC04G_E3F1B92D_20210430_111800.extcsd
30-Apr-21 11:18:00 AM> EMMC Init completed.
30-Apr-21 11:18:00 AM> 
30-Apr-21 11:18:00 AM> Operation: Reading from eMMC...
30-Apr-21 11:18:00 AM> 
30-Apr-21 11:18:02 AM> Reading from: ROM3 , start: 0x000000000000 , size: 0x000000200000
30-Apr-21 11:18:02 AM> Output file: P:\Mobile\Jtag\Acer\EMMC_MMC04G_ROM3_000000000000_000000200000.bin
30-Apr-21 11:18:02 AM> eMMC switching to ROM3
30-Apr-21 11:18:03 AM> Reading partition...
30-Apr-21 11:18:03 AM> Done reading partition. Read speed: 2617.92 Kb/s
30-Apr-21 11:18:15 AM> 
30-Apr-21 11:18:26 AM> 
30-Apr-21 11:18:26 AM> All done   time: [00:00:23:730]
30-Apr-21 11:18:26 AM> 
30-Apr-21 11:18:36 AM> Looking for EasyJTAG box...
30-Apr-21 11:18:36 AM> EasyJTAG API ver. 3403
30-Apr-21 11:18:36 AM> Setting IO Levels to 1.8V
30-Apr-21 11:18:36 AM> Setting frequence to 36 MHz
30-Apr-21 11:18:36 AM> EasyJTAG Box Serial = 0014D520AAB084B4
30-Apr-21 11:18:36 AM> EasyJTAG Box Firmware = 2.5301
30-Apr-21 11:18:38 AM> Setting interface to EasyJtag2/ISP_HiPower
30-Apr-21 11:18:38 AM> Setting bus width to 1 Bit
30-Apr-21 11:18:38 AM> HiPower mode is ON
30-Apr-21 11:18:38 AM> Setting frequence to 36 MHz
30-Apr-21 11:18:38 AM> CMD Pullup Level: 1828 mV
30-Apr-21 11:18:38 AM> CMD Active Level: 1881 mV
30-Apr-21 11:18:38 AM> eMMC Init returned = 0
30-Apr-21 11:18:38 AM> EMMC Device Information :
30-Apr-21 11:18:38 AM> EMMC CID: 7001004D4D4330344758E3F1B92D9195
30-Apr-21 11:18:38 AM> EMMC CSD: D04F01320F5903FFFFFFFFE78A400051
30-Apr-21 11:18:38 AM> EMMC Manufacture : KINGSTONE , EMMC NAME: MMC04G , HEX: 4D4D43303447 , S/N: E3F1B92D , rev. 0x58
30-Apr-21 11:18:38 AM> EMMC Manufacture ID: 0x70 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 9/2014
30-Apr-21 11:18:38 AM>    EMMC ROM 1 (Main User Data) Capacity: 3688 MB (0000E6800000)
30-Apr-21 11:18:38 AM>    EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 2048 KB (000000200000)
30-Apr-21 11:18:38 AM>    EMMC RPMB (Replay Protected Memory Block) Capacity: 128 KB (000000020000) Counter: 0 , Response: Clean
30-Apr-21 11:18:38 AM> EMMC Permanent Write Protection: No
30-Apr-21 11:18:38 AM> EMMC Temporary Write Protection: No
30-Apr-21 11:18:38 AM> Extended CSD Information :
30-Apr-21 11:18:38 AM> Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
30-Apr-21 11:18:38 AM> Boot configuration [PARTITION_CONFIG]: 0x48 , Boot from: ROM2 (Boot partition 1)
30-Apr-21 11:18:38 AM> Boot Bus Config: 0x00 , width 1bit
30-Apr-21 11:18:38 AM> H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
30-Apr-21 11:18:38 AM> Supported partition features [PARTITIONING_SUPPORT]: 0x07
30-Apr-21 11:18:38 AM> Device supports partitioning features
30-Apr-21 11:18:38 AM> Device can have enhanced technological features in partitions and user data area
30-Apr-21 11:18:38 AM> Device can have extended partitions attribute
30-Apr-21 11:18:38 AM> Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
30-Apr-21 11:18:39 AM> Backup saved: MMC04G_E3F1B92D_20210430_111839.extcsd
30-Apr-21 11:18:39 AM> EMMC Init completed.
30-Apr-21 11:18:39 AM> 
30-Apr-21 11:18:39 AM> Operation: File Explorer...
30-Apr-21 11:18:39 AM> 
30-Apr-21 11:18:39 AM> Scan from: MMC04G
30-Apr-21 11:18:39 AM> 
30-Apr-21 11:18:39 AM> Vendor: Mediatek
30-Apr-21 11:18:39 AM> Searching GPT ...
30-Apr-21 11:18:39 AM> GPT header is not found
30-Apr-21 11:18:39 AM> Searching PMT (MediaTek) ...
30-Apr-21 11:18:52 AM> PMT found at address 0x0000E6701000
30-Apr-21 11:18:52 AM> Searching MBR ...
30-Apr-21 11:18:52 AM> MBR found
30-Apr-21 11:18:52 AM> 
30-Apr-21 11:18:53 AM> Scan done
30-Apr-21 11:18:53 AM> 
30-Apr-21 11:18:53 AM> Mount [PROTECT_F] successfully   PartType: LINUX
30-Apr-21 11:18:53 AM> Mount [PROTECT_S] successfully   PartType: LINUX
30-Apr-21 11:18:53 AM> Mount [system] successfully   PartType: LINUX
30-Apr-21 11:18:53 AM> Mount [cache] successfully   PartType: LINUX
30-Apr-21 11:18:53 AM> Mount [data] successfully   PartType: LINUX
30-Apr-21 11:18:53 AM> 
30-Apr-21 11:18:53 AM> Get firmware version
30-Apr-21 11:18:53 AM> Brand = acer
30-Apr-21 11:18:53 AM> Manufacturer = Acer
30-Apr-21 11:18:53 AM> Device = acer_z205p
30-Apr-21 11:18:53 AM> Model = Z205
30-Apr-21 11:18:53 AM> CPU Abi = armeabi-v7a
30-Apr-21 11:18:53 AM> Mediatek platform = MT6572
30-Apr-21 11:18:53 AM> Android release = 4.4.2
30-Apr-21 11:18:53 AM> Firmware version = Acer_AV0K0_Z205P_1.003.00_AAP_DIGIHID
30-Apr-21 11:18:53 AM> Firmware date = 2014? 09? 24? ??? 09:32:33 CST

Here log Infinity its says

Operation : HW Test [ v1.58 ]

1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
Phone found! [ 8 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer   : 0x0005
BLVersion : 0x00FE
PreLoader : NOT Active [ Erased ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 7001004D4D4330344758E3F1B92D9195
Initialize Memory ... 

[DA_ERROR] : DRAM Configure failed!
ErroCode : 0xBE0B0000
EMICFG_RET_FAILED
CodeDefine : DA_DRAMC_RANK0_CALIBRATION_FAILED
Boot Error!

Operation Failed
Elapsed: 00:00:36
Reconnect Power/Cable!

[layder]

Not dead - it's checks and read