Xiaomi Redmi S2 - GSM-Forum

aydin.gsm1 · 05-12-2019, 08:35

hi guys,
I need full EMMC dump for xiaomi redmi S2/Y2 emergency.
please share your backups.
thanks in advance.

layder · 05-20-2019, 10:13

Quote:

Originally Posted by aydin.gsm1

hi guys,
I need full EMMC dump for xiaomi redmi S2/Y2 emergency.
please share your backups.
thanks in advance.

https://mega.nz/#!TVxiHS6B!uQVe3gfn_...gFnSq5CSNzvMqs

Redmi S2 backup by vendor w/o system & userdata

aydin.gsm1 · 05-22-2019, 15:07

hey bro! the device turned alive!
thank you so much...

aydin.gsm1 · 05-23-2019, 17:15

Quote:

Originally Posted by layder

https://mega.nz/#!TVxiHS6B!uQVe3gfn_...gFnSq5CSNzvMqs

Redmi S2 backup by vendor w/o system & userdata

can you please give me redmi s2 service manual sir?

aydin.gsm1 · 05-24-2019, 12:54

battery connector ways need please.

raisalina · 05-25-2019, 12:34

Quote:

Originally Posted by aydin.gsm1

battery connector ways need please.

aydin.gsm1 · 05-28-2019, 08:20

Quote:

Originally Posted by raisalina

sir, maybe one way is wrong
the device powered once at ten times (only with charger)
your solution not working.

aydin.gsm1 · 05-31-2019, 12:55

Quote:

Originally Posted by aydin.gsm1

sir, maybe one way is wrong
the device powered once at ten times (only with charger)
your solution not working.

isn't there any schematic for redmi s2/y2?

Jane1 · 06-26-2019, 17:04

Xiaomi Redmi S2, when connected to a computer, shows QLoader 9008 error.
I desolder eMMC and checked with EasyJtag :

Setting frequence to 21 Mhz
CMD Pullup Level: 3217 mV
CMD Active Level: 3310 mV
EMMC Device Information :
EMMC CID: 0600003136FFFFFFFFFF195C493934EA
EMMC CSD: 8C4F012A0F598000F6D801E08A400076
EMMC Manufacture : , EMMC NAME: 16 , HEX: 313600000000 , S/N: 195C4939 , rev. 0xFF
EMMC Manufacture ID: 0x06 , OEM ID: 0x00 , Device Type: Device (removable) , Date: 3/2017
EMMC ROM 1 (Main User Data) Capacity: 31596 MB (0007B6C80000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 0 KB (000000000000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 0 KB (000000000000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: Yes
Extended CSD Information :
Extended CSD rev: 1.7 (MMC 5.0, MMC 5.01)
Boot configuration [PARTITION_CONFIG]: 0x00 , Boot from: no boot
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: 16_195C4939_20190626_161702.extcsd
EMMC Init completed.

Error: EMMC Password Locked

Setting frequence to 21 Mhz
CMD Pullup Level: 3217 mV
CMD Active Level: 3310 mV
EMMC Device Information :
EMMC CID: 0600003136FFFFFFFFFF195C493934EA
EMMC CSD: 8C4F012A0F598000F6D801E08A400076
EMMC Manufacture : , EMMC NAME: 16 , HEX: 313600000000 , S/N: 195C4939 , rev. 0xFF
EMMC Manufacture ID: 0x06 , OEM ID: 0x00 , Device Type: Device (removable) , Date: 3/2017
EMMC ROM 1 (Main User Data) Capacity: 31596 MB (0007B6C80000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 0 KB (000000000000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 0 KB (000000000000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: Yes
Extended CSD Information :
Extended CSD rev: 1.7 (MMC 5.0, MMC 5.01)
Boot configuration [PARTITION_CONFIG]: 0x00 , Boot from: no boot
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: 16_195C4939_20190626_161722.extcsd
EMMC Init completed.

Operation: File Explorer...

Scan from: 16
Error reading at address: 000000000000 , error: -206, PORT Read Error ... Retry #1
Error reading at address: 000000000000 , error: -206, PORT Read Error ... Retry #2
Error reading at address: 000000000000 , error: -206, PORT Read Error ... Retry #3
Too many errors. Reading has been stopped

Error reading at address: 0007B6C7C000 , error: -206, PORT Read Error ... Retry #1
Error reading at address: 0007B6C7C000 , error: -206, PORT Read Error ... Retry #2
Error reading at address: 0007B6C7C000 , error: -206, PORT Read Error ... Retry #3
Too many errors. Reading has been stopped

Vendor: Qualcomm
Searching GPT ...
Error reading at address: 000000000000 , error: -206, PORT Read Error ... Retry #1
Error reading at address: 000000000000 , error: -206, PORT Read Error ... Retry #2
Error reading at address: 000000000000 , error: -206, PORT Read Error ... Retry #3
Too many errors. Reading has been stopped

GPT header is not found
Searching MBR ...
Error reading at address: 000000000000 , error: -206, PORT Read Error ... Retry #1
Error reading at address: 000000000000 , error: -206, PORT Read Error ... Retry #2
Error reading at address: 000000000000 , error: -206, PORT Read Error ... Retry #3
Too many errors. Reading has been stopped

MBR header is not found
Partition table not found

Is it enough to test that eMMC is OK and the QLoader 9008 error is caused by something else?
Thanks for reply

umar342 · 06-28-2019, 17:20

partion is currupt resize partion or flash with dump

Jane1 · 06-28-2019, 21:22

Thanks for the reply. Do you mean that eMMC itself ( hardware) is good?
But if I flash with dump will it work? It is Xiaomi and eMMC is linked with CPU.
Or can you let me know how to resize the partition?

ishant · 06-29-2019, 06:31

EMMC Password Locked: Yes
Extended CSD Information :
Extended CSD rev: 1.7 (MMC 5.0, MMC 5.01)

layder · 06-29-2019, 08:09

Quote:

Originally Posted by ishant

EMMC Password Locked: Yes
Extended CSD Information :
Extended CSD rev: 1.7 (MMC 5.0, MMC 5.01)

Try to use "Erase e(MMC) password" and "Universal Format Repair" function at EasyJTAG classic software

umar342 · 06-29-2019, 18:47

Quote:

Originally Posted by Jane1

Thanks for the reply. Do you mean that eMMC itself ( hardware) is good?
But if I flash with dump will it work? It is Xiaomi and eMMC is linked with CPU.
Or can you let me know how to resize the partition?

just farmat factry reset and wright full dump no need to resise partion

Jane1 · 07-01-2019, 10:39

Thank you for your replies.
@layder: But when using the latest EasyJtag version, it does not reports Password protected

Setting frequence to 21 MHz
CMD Pullup Level: 3021 mV
CMD Active Level: 1815 mV
EMMC Device Information :
EMMC CID: 0600003136FFFFFFFFFF195C493934EA
EMMC CSD: 8C4F012A0F598000F6D801E08A400076
EMMC Manufacture : , EMMC NAME: 16 , HEX: 313600000000 , S/N: 195C4939 , rev. 0xFF
EMMC Manufacture ID: 0x06 , OEM ID: 0x00 , Device Type: Device (removable) , Date: 3/2001
EMMC ROM 1 (Main User Data) Capacity: 31596 MB (0007B6C80000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 0 KB (000000000000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 0 KB (000000000000) Counter: 0 , Response: Maybe not clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.0 (MMC 4.0)
Boot configuration [PARTITION_CONFIG]: 0x00 , Boot from: no boot
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x00
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: 16_195C4939_20190627_095207.extcsd
EMMC Init completed.

Do you have any explanation?

I can try to format eMMC and write dump, but isn't eMMC linked with CPU in Xiaomi?
And eMMC can not be replaced but only together with CPU from the same mainboard?
Can EasyJtag help?
Any advice?
Thank you for help

05-12-2019, 08:35	#1 (permalink)
aydin.gsm1 Freak Poster Join Date: Jun 2010 Location: South Azerbaycan Age: 40 Posts: 372 Member: 1333047 Status: Offline Sonork: 100.1618775 Thanks Meter: 278	need redmi s2/y2 full dump hi guys, I need full EMMC dump for xiaomi redmi S2/Y2 emergency. please share your backups. thanks in advance.

06-26-2019, 17:04	#9 (permalink)
Jane1 No Life Poster Join Date: Jan 2010 Posts: 755 Member: 1212133 Status: Offline Thanks Meter: 58	Xiaomi Redmi S2 - eMMC - good or bad? Xiaomi Redmi S2, when connected to a computer, shows QLoader 9008 error. I desolder eMMC and checked with EasyJtag : Setting frequence to 21 Mhz CMD Pullup Level: 3217 mV CMD Active Level: 3310 mV EMMC Device Information : EMMC CID: 0600003136FFFFFFFFFF195C493934EA EMMC CSD: 8C4F012A0F598000F6D801E08A400076 EMMC Manufacture : , EMMC NAME: 16 , HEX: 313600000000 , S/N: 195C4939 , rev. 0xFF EMMC Manufacture ID: 0x06 , OEM ID: 0x00 , Device Type: Device (removable) , Date: 3/2017 EMMC ROM 1 (Main User Data) Capacity: 31596 MB (0007B6C80000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 0 KB (000000000000) EMMC RPMB (Replay Protected Memory Block) Capacity: 0 KB (000000000000) EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No EMMC Password Locked: Yes Extended CSD Information : Extended CSD rev: 1.7 (MMC 5.0, MMC 5.01) Boot configuration [PARTITION_CONFIG]: 0x00 , Boot from: no boot Boot Bus Config: 0x00 , width 1bit H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled Supported partition features [PARTITIONING_SUPPORT]: 0x07 Device supports partitioning features Device can have enhanced technological features in partitions and user data area Device can have extended partitions attribute Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00 Backup saved: 16_195C4939_20190626_161702.extcsd EMMC Init completed. Error: EMMC Password Locked Setting frequence to 21 Mhz CMD Pullup Level: 3217 mV CMD Active Level: 3310 mV EMMC Device Information : EMMC CID: 0600003136FFFFFFFFFF195C493934EA EMMC CSD: 8C4F012A0F598000F6D801E08A400076 EMMC Manufacture : , EMMC NAME: 16 , HEX: 313600000000 , S/N: 195C4939 , rev. 0xFF EMMC Manufacture ID: 0x06 , OEM ID: 0x00 , Device Type: Device (removable) , Date: 3/2017 EMMC ROM 1 (Main User Data) Capacity: 31596 MB (0007B6C80000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 0 KB (000000000000) EMMC RPMB (Replay Protected Memory Block) Capacity: 0 KB (000000000000) EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No EMMC Password Locked: Yes Extended CSD Information : Extended CSD rev: 1.7 (MMC 5.0, MMC 5.01) Boot configuration [PARTITION_CONFIG]: 0x00 , Boot from: no boot Boot Bus Config: 0x00 , width 1bit H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled Supported partition features [PARTITIONING_SUPPORT]: 0x07 Device supports partitioning features Device can have enhanced technological features in partitions and user data area Device can have extended partitions attribute Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00 Backup saved: 16_195C4939_20190626_161722.extcsd EMMC Init completed. Operation: File Explorer... Scan from: 16 Error reading at address: 000000000000 , error: -206, PORT Read Error ... Retry #1 Error reading at address: 000000000000 , error: -206, PORT Read Error ... Retry #2 Error reading at address: 000000000000 , error: -206, PORT Read Error ... Retry #3 Too many errors. Reading has been stopped Error reading at address: 0007B6C7C000 , error: -206, PORT Read Error ... Retry #1 Error reading at address: 0007B6C7C000 , error: -206, PORT Read Error ... Retry #2 Error reading at address: 0007B6C7C000 , error: -206, PORT Read Error ... Retry #3 Too many errors. Reading has been stopped Vendor: Qualcomm Searching GPT ... Error reading at address: 000000000000 , error: -206, PORT Read Error ... Retry #1 Error reading at address: 000000000000 , error: -206, PORT Read Error ... Retry #2 Error reading at address: 000000000000 , error: -206, PORT Read Error ... Retry #3 Too many errors. Reading has been stopped GPT header is not found Searching MBR ... Error reading at address: 000000000000 , error: -206, PORT Read Error ... Retry #1 Error reading at address: 000000000000 , error: -206, PORT Read Error ... Retry #2 Error reading at address: 000000000000 , error: -206, PORT Read Error ... Retry #3 Too many errors. Reading has been stopped MBR header is not found Partition table not found Is it enough to test that eMMC is OK and the QLoader 9008 error is caused by something else? Thanks for reply

05-22-2019, 15:07	#3 (permalink)
aydin.gsm1 Freak Poster Join Date: Jun 2010 Location: South Azerbaycan Age: 40 Posts: 372 Member: 1333047 Status: Offline Sonork: 100.1618775 Thanks Meter: 278	hey bro! the device turned alive! thank you so much...

05-24-2019, 12:54	#5 (permalink)
aydin.gsm1 Freak Poster Join Date: Jun 2010 Location: South Azerbaycan Age: 40 Posts: 372 Member: 1333047 Status: Offline Sonork: 100.1618775 Thanks Meter: 278	battery connector ways need please.

06-28-2019, 17:20	#10 (permalink)
umar342 No Life Poster Join Date: Feb 2010 Location: india Posts: 1,085 Member: 1246696 Status: Offline Sonork: 100.1681950 Thanks Meter: 650	partion is currupt resize partion or flash with dump

06-28-2019, 21:22	#11 (permalink)
Jane1 No Life Poster Join Date: Jan 2010 Posts: 755 Member: 1212133 Status: Offline Thanks Meter: 58	Thanks for the reply. Do you mean that eMMC itself ( hardware) is good? But if I flash with dump will it work? It is Xiaomi and eMMC is linked with CPU. Or can you let me know how to resize the partition?

06-29-2019, 06:31	#12 (permalink)
ishant No Life Poster Join Date: May 2012 Location: InfinityBox CM2 Posts: 615 Member: 1763238 Status: Offline Thanks Meter: 370	EMMC Password Locked: Yes Extended CSD Information : Extended CSD rev: 1.7 (MMC 5.0, MMC 5.01)

07-01-2019, 10:39	#15 (permalink)
Jane1 No Life Poster Join Date: Jan 2010 Posts: 755 Member: 1212133 Status: Offline Thanks Meter: 58	Thank you for your replies. @layder: But when using the latest EasyJtag version, it does not reports Password protected Setting frequence to 21 MHz CMD Pullup Level: 3021 mV CMD Active Level: 1815 mV EMMC Device Information : EMMC CID: 0600003136FFFFFFFFFF195C493934EA EMMC CSD: 8C4F012A0F598000F6D801E08A400076 EMMC Manufacture : , EMMC NAME: 16 , HEX: 313600000000 , S/N: 195C4939 , rev. 0xFF EMMC Manufacture ID: 0x06 , OEM ID: 0x00 , Device Type: Device (removable) , Date: 3/2001 EMMC ROM 1 (Main User Data) Capacity: 31596 MB (0007B6C80000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 0 KB (000000000000) EMMC RPMB (Replay Protected Memory Block) Capacity: 0 KB (000000000000) Counter: 0 , Response: Maybe not clean EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD Information : Extended CSD rev: 1.0 (MMC 4.0) Boot configuration [PARTITION_CONFIG]: 0x00 , Boot from: no boot Boot Bus Config: 0x00 , width 1bit H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled Supported partition features [PARTITIONING_SUPPORT]: 0x00 Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00 Backup saved: 16_195C4939_20190627_095207.extcsd EMMC Init completed. Do you have any explanation? I can try to format eMMC and write dump, but isn't eMMC linked with CPU in Xiaomi? And eMMC can not be replaced but only together with CPU from the same mainboard? Can EasyJtag help? Any advice? Thank you for help