New version 2.1 of the SIM-EMU 6.01 configurator program - Page 6 - GSM-Forum

satzone · 03-16-2005, 15:27

Dear SimEmu
I have your last SIM_EMU_6.01_CFG_v2.1.msi, but with some problems. Because in Nokia and Samsung X100 when i am selecting phone number from Sel.phone# then it is switching very well but in other sets is not switching to other number then i am going on other number after switch off/on, enter pin for other number and then number does work.
You are requested to please give me your nice opinion on this problem that how i can solve this problem i.e. how i can switched an other number through Sel.phone# instead of switch off/on.
An early attention is requested.

SATZONE

simemu · 03-16-2005, 19:54

That is a problem of some mobile models. The "Sel Phone#" does not work because they don't implement the Refresh command the way as GSM rules dictate.
The only way to change is, as you say, resetting and entering a PIN of another position.

Regards

bad_signal · 03-20-2005, 01:25

under testing
but i wanna to no that if there is some tool for that prog
and i have some tool for that prog called dr.sim
it can explore the sim card
but it can't read the bad sim and damage card
can i have some sort of prog can read that bad or damage card

natasha2005 · 03-22-2005, 12:04

Hi Simemu,
I have downloaded Sim-emu 6.01 v2.1.
I am using 'Infinity Usb Phoenix' with Silver Card.
I have already extracted the Ki with simscan.

But Im having some difficulty when using SimEmu software:
1. When I used my silver card in 'Infinity Usb Phoenix', SimEmu cannot detect my card "No Card Inserted"
2. I have inserted my ki & imsi in 'Configure' and 'write to card' but could not write "Inserted a GSM or SIM-EMU card"
3. When I try to 'write to disk' the msg popup "Load the Sim Emu flash & Eeprom file first"
4. Where should I load the flash & Eeprom?

Please help me. Im really confused. I have gone through all your forum. I have also read your 'help' but without success.
Regards,
Natasha.

simemu · 03-22-2005, 18:22

If the Infinity USB Phoenix cannot be configured using a COMx port, the SIM-EMU Configurator cannot be used with this type of Phoenix (The Phoenix PlugIn requires a valid COMx port to communicate with the Phoenix). Read the Infinity USB Phoenix manual.

In this case, I recommend you to use the "First time configuration over an empty GreenCard2 / GreenCard /SilverCard" described in the "Help" tabsheet of SIM-EMU Configurator, but you will need to write EEPROM with the programmer software included with your Phoenix.

Regards

natasha2005 · 03-23-2005, 04:35

Hi Simemu,
Thanks for your help.
Well, I have been able to copy my silver card using Simemu 6.01 v2.1 with 'Infinity usb Phoenix'.

Thanks for you and your team for the super software 'Simemu6.01 v2.1'

Regards,
Natasha

samehabdelaziz · 05-23-2005, 13:37

Dear all,
Thank you all for the good knowledge i can find here!
Actually i am new here .. but i need to extract Ki and IMSI from my SIM Card i have.
I want to know the exact requirement needed for that and from where i can get it.
Per example, what is the Reader needed? Is there any special specification? There is a lot of softwares, Which one is more effective? I will be waiting for your reply on my mail: [email protected]
Thanx a lot ... Please i need your help!
Bregards, Sameh

ducksat · 05-25-2005, 00:30

HI all!
Simemu, i have problem after programing simemu card. When I switch phone on I must enter pin. I tried x combination: 0000, 1111, 2222, 9999, 1234 and is not. Can you help me? What I doo wrong?

PN.ItalyGirl · 05-26-2005, 08:24

Use PUK 12345678 and then change your PIN...

ducksat · 05-27-2005, 09:27

ThnX, I will try later.

ducksat · 05-28-2005, 08:36

Wrong, PUK is not 12345678 and is not usual.
CAN SOMEBODY SEND ME FILES (Sim_emu_6.01_Fl.hex & Sim_emu_6.01_ep.hex) WITH PREPROGRAMED PIN & PUK, OR PUK only.
Thanks

simemu · 05-28-2005, 16:05

In my page www.simemu.cjb.net you will find the original SIM-EMU files with the default PIN's/PUK's as I describe in the page.

Regards

ducksat · 05-31-2005, 16:56

Thnx simemu for all.
But I'm still without pin for sim_emu card. I programming FL and EP files with card writer 2.0. Should i program with IC Prog or else. I use mastera IV on 6 mhz. I fill the silver card without IMSI and KI's for my cards. I put on the card only files you tell me. Sholud I first put my IMSI and KI's and then program card. Your Sim_emu configurator 6.01 detect my sim_emu card as card 6.01, but i can't write on it because ask mee for pin1. How can i change im or enter the right pin. Your files comes with programed pin. If you can send me files on PM with PIN's please.
Thank you again

CH@IN · 05-31-2005, 20:04

Quote:

Originally Posted by ducksat

Should i program with IC Prog or else.

Try it with icprog, maybe you didn't store anything into the Eprom section yet. Follow EXACTLY the instructions as given in the pages of SIM-EMU.

aasifnasim · 06-02-2005, 15:58

can someone give me idea wat i have to do for sim cloning;
hardware/software both
i have nokia phone and i have to carry two cell phone but i don want that
i want to make clone my two sim.... and use in a single cell phone to plz do help me out from this problem
i m capable to write down some programs in number of languages

03-23-2005, 04:35	#81 (permalink)
natasha2005 Junior Member Join Date: Feb 2005 Age: 48 Posts: 7 Member: 118366 Status: Offline Thanks Meter: 0	Hi Simemu, Thanks for your help. Well, I have been able to copy my silver card using Simemu 6.01 v2.1 with 'Infinity usb Phoenix'. Thanks for you and your team for the super software 'Simemu6.01 v2.1' Regards, Natasha Last edited by natasha2005; 03-23-2005 at 13:29.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Sim-Emu 6.01 Configurator v2.1	sonojee	Nokia Multimedia	0	03-26-2009 19:32
problem Sim-Emu 6.01 Configurator v2.1	شاكر	Sim Cloning and Scaning	3	05-16-2008 21:34
what shematic for Sim-Emu 6.01 Configurator v2.1	clinic*mobile	Sim Cloning and Scaning	9	08-22-2005 06:38
New SIM-EMU 6.01 with Arabic menu language	simemu	Sim Cloning and Scaning	17	09-03-2003 22:08
New SIM-EMU 6.01 with Slovak menu language	simemu	Sim Cloning and Scaning	0	08-20-2003 17:15

03-16-2005, 15:27	#76 (permalink)
satzone Banned Join Date: Jan 2005 Location: On The Earth Posts: 189 Member: 107545 Status: Offline Thanks Meter: 44	Dear SimEmu I have your last SIM_EMU_6.01_CFG_v2.1.msi, but with some problems. Because in Nokia and Samsung X100 when i am selecting phone number from Sel.phone# then it is switching very well but in other sets is not switching to other number then i am going on other number after switch off/on, enter pin for other number and then number does work. You are requested to please give me your nice opinion on this problem that how i can solve this problem i.e. how i can switched an other number through Sel.phone# instead of switch off/on. An early attention is requested. SATZONE

03-16-2005, 19:54	#77 (permalink)
simemu No Life Poster Join Date: Apr 2002 Location: Spain Age: 62 Posts: 855 Member: 10582 Status: Offline Thanks Meter: 99	That is a problem of some mobile models. The "Sel Phone#" does not work because they don't implement the Refresh command the way as GSM rules dictate. The only way to change is, as you say, resetting and entering a PIN of another position. Regards

03-20-2005, 01:25	#78 (permalink)
bad_signal Freak Poster Join Date: Jan 2005 Location: With My !!!? Posts: 456 Member: 107069 Status: Offline Thanks Meter: 31	under testing but i wanna to no that if there is some tool for that prog and i have some tool for that prog called dr.sim it can explore the sim card but it can't read the bad sim and damage card can i have some sort of prog can read that bad or damage card

03-22-2005, 12:04	#79 (permalink)
natasha2005 Junior Member Join Date: Feb 2005 Age: 48 Posts: 7 Member: 118366 Status: Offline Thanks Meter: 0	Hi Simemu, I have downloaded Sim-emu 6.01 v2.1. I am using 'Infinity Usb Phoenix' with Silver Card. I have already extracted the Ki with simscan. But Im having some difficulty when using SimEmu software: 1. When I used my silver card in 'Infinity Usb Phoenix', SimEmu cannot detect my card "No Card Inserted" 2. I have inserted my ki & imsi in 'Configure' and 'write to card' but could not write "Inserted a GSM or SIM-EMU card" 3. When I try to 'write to disk' the msg popup "Load the Sim Emu flash & Eeprom file first" 4. Where should I load the flash & Eeprom? Please help me. Im really confused. I have gone through all your forum. I have also read your 'help' but without success. Regards, Natasha.

03-22-2005, 18:22	#80 (permalink)
simemu No Life Poster Join Date: Apr 2002 Location: Spain Age: 62 Posts: 855 Member: 10582 Status: Offline Thanks Meter: 99	If the Infinity USB Phoenix cannot be configured using a COMx port, the SIM-EMU Configurator cannot be used with this type of Phoenix (The Phoenix PlugIn requires a valid COMx port to communicate with the Phoenix). Read the Infinity USB Phoenix manual. In this case, I recommend you to use the "First time configuration over an empty GreenCard2 / GreenCard /SilverCard" described in the "Help" tabsheet of SIM-EMU Configurator, but you will need to write EEPROM with the programmer software included with your Phoenix. Regards

05-23-2005, 13:37	#82 (permalink)
samehabdelaziz Junior Member Join Date: May 2005 Age: 44 Posts: 2 Member: 147414 Status: Offline Thanks Meter: 0	Dear all, Thank you all for the good knowledge i can find here! Actually i am new here .. but i need to extract Ki and IMSI from my SIM Card i have. I want to know the exact requirement needed for that and from where i can get it. Per example, what is the Reader needed? Is there any special specification? There is a lot of softwares, Which one is more effective? I will be waiting for your reply on my mail: [email protected] Thanx a lot ... Please i need your help! Bregards, Sameh

05-25-2005, 00:30	#83 (permalink)
ducksat Junior Member Join Date: May 2005 Age: 50 Posts: 6 Member: 146373 Status: Offline Thanks Meter: 0	HI all! Simemu, i have problem after programing simemu card. When I switch phone on I must enter pin. I tried x combination: 0000, 1111, 2222, 9999, 1234 and is not. Can you help me? What I doo wrong?

05-26-2005, 08:24	#84 (permalink)
PN.ItalyGirl Insane Poster Join Date: Apr 2005 Posts: 80 Member: 137168 Status: Offline Thanks Meter: 3	Use PUK 12345678 and then change your PIN...

05-27-2005, 09:27	#85 (permalink)
ducksat Junior Member Join Date: May 2005 Age: 50 Posts: 6 Member: 146373 Status: Offline Thanks Meter: 0	ThnX, I will try later.

05-28-2005, 08:36	#86 (permalink)
ducksat Junior Member Join Date: May 2005 Age: 50 Posts: 6 Member: 146373 Status: Offline Thanks Meter: 0	Wrong, PUK is not 12345678 and is not usual. CAN SOMEBODY SEND ME FILES (Sim_emu_6.01_Fl.hex & Sim_emu_6.01_ep.hex) WITH PREPROGRAMED PIN & PUK, OR PUK only. Thanks

05-28-2005, 16:05	#87 (permalink)
simemu No Life Poster Join Date: Apr 2002 Location: Spain Age: 62 Posts: 855 Member: 10582 Status: Offline Thanks Meter: 99	In my page www.simemu.cjb.net you will find the original SIM-EMU files with the default PIN's/PUK's as I describe in the page. Regards

05-31-2005, 16:56	#88 (permalink)
ducksat Junior Member Join Date: May 2005 Age: 50 Posts: 6 Member: 146373 Status: Offline Thanks Meter: 0	Thnx simemu for all. But I'm still without pin for sim_emu card. I programming FL and EP files with card writer 2.0. Should i program with IC Prog or else. I use mastera IV on 6 mhz. I fill the silver card without IMSI and KI's for my cards. I put on the card only files you tell me. Sholud I first put my IMSI and KI's and then program card. Your Sim_emu configurator 6.01 detect my sim_emu card as card 6.01, but i can't write on it because ask mee for pin1. How can i change im or enter the right pin. Your files comes with programed pin. If you can send me files on PM with PIN's please. Thank you again

06-02-2005, 15:58	#90 (permalink)
aasifnasim Freak Poster Join Date: May 2005 Location: India Posts: 369 Member: 148720 Status: Offline Thanks Meter: 16	can someone give me idea wat i have to do for sim cloning; hardware/software both i have nokia phone and i have to carry two cell phone but i don want that i want to make clone my two sim.... and use in a single cell phone to plz do help me out from this problem i m capable to write down some programs in number of languages