Repairing SC6531 With Volcano is So Easy That I Wish All Faulty Mobiles have This CPU - GSM-Forum

Moiz Khan · 03-15-2015, 07:40

Repairing SC6531/SC6531D/SC6531DA With Volcano is So Easy That I Wish All Incoming Faulty Mobiles Were SC6531

Till Date I have Repaired More Than 5000 SC6531 Handsets, Only 2-3 of them I had returned to Customer Just Because Of Bad Flash Files, Otherwise All Handsets were revived Successfully.

Only Following Below Given Universal Method (Most Of You Know This Very Well) :

* READ FLASH FILE
* LOAD/SELECT YOUR READED FLASH FILE
* DO FORMAT
(Check Now if phone got ok)

If Not Got Ok, then
* WRITE FLASH FILE
* AGAIN DO FORMAT
(Check Now phone got ok)

NOTE : Best Way to check Phone is On Volcano Eagle Eye.

OR Insert Full Charged Battery & Press Power Button for atleast 1minute

I'll Post Many Logs Here To Show You All People That Volcano is Not A Useless Device As Many Of You People Always Blame. Please Check & Observe All Logs Carefully.

If You Want Flash Files, You can Find It in Volcano Flash Files Section Or On My Support.

bR. Moiz Khan
(Volcano Team)

Moiz Khan · 03-15-2015, 07:45

Code:

Detection initiated...
  Vcc: null
  Gnd: 5
  Analyzing D+ and D-...
  D+ = 3, D- = 2
  Detection D+/D- with 1.34 seconds.
  Continue to detect BOOT pin...
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
  UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
  Setting...
  Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
  Pinouts setting complete!
    
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310000]
  FLASH ID: 00C8006000160000
  Flash Type:[GD]  25LG32bWL
  Size:0x400000(4MB)
  Reading completed.
  The data has been saved in D:\FLASH FILES\SC6531\ZEN X13 {SC6531 [GD] 25LG32bWL} Cable - 05b.bin, size: 4 M.
  Detection initiated...
  Vcc: null
  Gnd: 5
  Analyzing D+ and D-...
  D+ = 3, D- = 2
  Detection D+/D- with 1.31 seconds.
  Continue to detect BOOT pin...
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
  UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
  Setting...
  Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
  Pinouts setting complete!
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310000]
  FLASH ID: 00C8006000160000
  Flash Type:[GD]  25LG32bWL
  Size:0x400000(4MB)
>>Set to Factory successfully.

Moiz Khan · 03-15-2015, 07:46

Code:

  Detection initiated...
  Vcc: null
  Gnd: 5
  Analyzing D+ and D-...
  D+ = 3, D- = 2
  Detection D+/D- with 1.30 seconds.
  Continue to detect BOOT pin...
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
  UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
  Setting...
  Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
  Pinouts setting complete!
    
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310001]
  FLASH ID: 00C8006000160000
  Flash Type: SF_GD25LQ32                
  Size:0x400000(4MB)
  Reading completed.
  The data has been saved in D:\FLASH FILES\SC6531\ZEN X13 (V1) {SC6531 [SF_GD25LQ32]} Cable - 05b Press LSK.bin, size: 4 M.
  Detection initiated...
  Vcc: null
  Gnd: 5
  Analyzing D+ and D-...
  D+ = 3, D- = 2
  Detection D+/D- with 1.33 seconds.
  Continue to detect BOOT pin...
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
  UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
  Setting...
  Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
  Pinouts setting complete!
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310001]
  FLASH ID: 00C8006000160000
  Flash Type: SF_GD25LQ32                
  Size:0x400000(4MB)
>>Set to Factory successfully.

Moiz Khan · 03-15-2015, 07:47

Code:

  Detection initiated...
  Vcc: null
  Gnd: 5
  Analyzing D+ and D-...
  D+ = 3, D- = 2
  Detection D+/D- with 1.28 seconds.
  Continue to detect BOOT pin...
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
  UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
  Setting...
  Find USB device:SCI USB2Serial (COM165), (VID_1782&PID_4D00)
  Pinouts setting complete!
    
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310000]
  FLASH ID: 00EF004000160000
  Flash Type:[WinBond]  W25Q32BV
  Size:0x400000(4MB)
  Reading completed.
  The data has been saved in C:\Documents and Settings\Shanu\Desktop\_20141128_143541_FullFlash zen x12.bin, size: 4 M.
  Detection initiated...
  Vcc: null
  Gnd: 5
  Analyzing D+ and D-...
  D+ = 3, D- = 2
  Detection D+/D- with 1.20 seconds.
  Continue to detect BOOT pin...
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
  UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
  Setting...
  Find USB device:SCI USB2Serial (COM165), (VID_1782&PID_4D00)
  Pinouts setting complete!
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310000]
  FLASH ID: 00EF004000160000
  Flash Type:[WinBond]  W25Q32BV
  Size:0x400000(4MB)

Moiz Khan · 03-15-2015, 07:48

Code:

  For many phones, charge pins need to be set in order to identify USB devices.
  Detecting D+ and D-...
  Vcc: null
  Gnd: 5
  Detection initiated...
  D+ = 3, D- = 2
  Detection D+/D- with 1.73 seconds.
  Continue to detect BOOT pin...
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
  UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
  Detection completed.
  Available Ports:COM1 COM3 COM4 
  Detection initiated...
  Vcc: null
  Gnd: 5
  Analyzing D+ and D-...
  D+ = 3, D- = 2
  Detection D+/D- with 1.31 seconds.
  Continue to detect BOOT pin...
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
  UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
  Setting...
  Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
  Pinouts setting complete!
    
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310001]
  FLASH ID: 00C8006000160000
  Flash Type: SF_GD25LQ32                
  Size:0x400000(4MB)
  Reading completed.
  The data has been saved in D:\FLASH FILES\SC6531\ZEN X9i {SC6531 [SF_GD25LQ32]} Cable - 05b.bin, size: 4 M.
  Detection initiated...
  Vcc: null
  Gnd: 5
  Analyzing D+ and D-...
  D+ = 3, D- = 2
  Detection D+/D- with 1.31 seconds.
  Continue to detect BOOT pin...
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
  UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
  Setting...
  Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
  Pinouts setting complete!
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310001]
  FLASH ID: 00C8006000160000
  Flash Type: SF_GD25LQ32                
  Size:0x400000(4MB)
>>Set to Factory successfully.

Moiz Khan · 03-15-2015, 07:49

Code:

  For many phones, charge pins need to be set in order to identify USB devices.
  Detecting D+ and D-...
  Vcc: null
  Gnd: 5
  Detection initiated...
  D+ = 3, D- = 2
  Detection D+/D- with 1.50 seconds.
  Continue to detect BOOT pin...
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
  UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
  Detection completed.
  Available Ports:COM1 COM3 COM4 
  Detection initiated...
  Vcc: null
  Gnd: 5
  Analyzing D+ and D-...
  D+ = 3, D- = 2
  Detection D+/D- with 1.28 seconds.
  Continue to detect BOOT pin...
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
  UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
  Setting...
  Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
  Pinouts setting complete!
    
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310001]
  FLASH ID: 00C8006000160000
  Flash Type: SF_GD25LQ32                
  Size:0x400000(4MB)
  Reading completed.
  The data has been saved in D:\FLASH FILES\SC6531\ZEN X4i {SC6531 [SF_GD25LQ32]} Cable - 05b.bin, size: 4 M.

Moiz Khan · 03-15-2015, 07:50

Code:

  Detection initiated...
  Vcc: 10
  Gnd: 1 4
  Analyzing D+ and D-...
  D+ = 9, D- = 8
  Detection D+/D- with 1.74 seconds.
  Continue to detect BOOT pin...
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
  BOOT(Pull Down) = 6
  Setting...
  Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
  Pinouts setting complete!
    
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310000]
  FLASH ID: 00EF004000160000
  Flash Type:[WinBond]  W25Q32BV
  Size:0x400000(4MB)
  Reading completed.
  The data has been saved in D:\FLASH FILES\SC6531\ZEN X4 {SC6531 [WinBond] W25Q32BV} Cable - 12c by Moiz Khan.bin, size: 4 M.
  Detection initiated...
  Vcc: 10
  Gnd: 1 4
  Analyzing D+ and D-...
  D+ = 9, D- = 8
  Detection D+/D- with 1.30 seconds.
  Continue to detect BOOT pin...
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
  BOOT(Pull Down) = 6
  Setting...
  Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
  Pinouts setting complete!
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310000]
  FLASH ID: 00EF004000160000
  Flash Type:[WinBond]  W25Q32BV
  Size:0x400000(4MB)
>>Set to Factory successfully.

Moiz Khan · 03-15-2015, 07:51

Code:

  Available Ports:COM1 COM4 COM112 
  Detection initiated...
  Vcc: null
  Gnd: 5
  Analyzing D+ and D-...
  D+ = 3, D- = 2
  Detection D+/D- with 1.38 seconds.
  Continue to detect BOOT pin...
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
  UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
  Setting...
  Find USB device:SCI USB2Serial (COM113), (VID_1782&PID_4D00)
  Pinouts setting complete!
    
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310000]
  FLASH ID: 00C8006000180000
  Flash Type:[GD]  25LQ128YIG
  Size:0x1000000(16MB)
  Reading completed.
  The data has been saved in C:\Documents and Settings\Shanu\Desktop\_20141115_190307_FullFlash Zen P37.bin, size: 16 M.
  Detection initiated...
  Vcc: null
  Gnd: 5
  Analyzing D+ and D-...
  D+ = 3, D- = 2
  Detection D+/D- with 1.20 seconds.
  Continue to detect BOOT pin...
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
  UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
  Setting...
  Find USB device:SCI USB2Serial (COM113), (VID_1782&PID_4D00)
  Pinouts setting complete!
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310000]
  FLASH ID: 00C8006000180000
  Flash Type:[GD]  25LQ128YIG
  Size:0x1000000(16MB)
>>Set to Factory successfully.

Moiz Khan · 03-15-2015, 07:52

Code:

  Detection initiated...
  Vcc: null
  Gnd: 5
  Analyzing D+ and D-...
  D+ = 3, D- = 2
  Detection D+/D- with 1.08 seconds.
  Continue to detect BOOT pin...
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
  UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
  Setting...
  Find USB device:SCI USB2Serial (COM165), (VID_1782&PID_4D00)
  Pinouts setting complete!
    
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310001]
  FLASH ID: 00C8006000160000
  Flash Type: SF_GD25LQ32                
  Size:0x400000(4MB)
  Reading completed.
  The data has been saved in C:\Documents and Settings\Shanu\Desktop\_20141122_142201_FullFlash ZEN M14.bin, size: 4 M.
  Detection initiated...
  Vcc: null
  Gnd: 5
  Analyzing D+ and D-...
  D+ = 3, D- = 2
  Detection D+/D- with 1.09 seconds.
  Continue to detect BOOT pin...
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
  UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
  Setting...
  Find USB device:SCI USB2Serial (COM165), (VID_1782&PID_4D00)
  Pinouts setting complete!
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310001]
  FLASH ID: 00C8006000160000
  Flash Type: SF_GD25LQ32                
  Size:0x400000(4MB)
>>Set to Factory successfully.

Moiz Khan · 03-15-2015, 07:53

Code:

  Detection initiated...
  Vcc: null
  Gnd: 5
  Analyzing D+ and D-...
  D+ = 3, D- = 2
  Detection D+/D- with 1.31 seconds.
  Continue to detect BOOT pin...
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
  UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
  Setting...
  Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
  Pinouts setting complete!
    
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310000]
  FLASH ID: 00C8006000160000
  Flash Type:[GD]  25LG32bWL
  Size:0x400000(4MB)
  Reading completed.
  The data has been saved in D:\FLASH FILES\SC6531\ZEN M7 {SC6531 [GD] 25LG32bWL} Cable - 05b press star button.bin, size: 4 M.
  Detection initiated...
  Vcc: null
  Gnd: 5
  Analyzing D+ and D-...
  D+ = 3, D- = 2
  Detection D+/D- with 1.67 seconds.
  Continue to detect BOOT pin...
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
  UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
  Setting...
  Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
  Pinouts setting complete!
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310000]
  FLASH ID: 00C8006000160000
  Flash Type:[GD]  25LG32bWL
  Size:0x400000(4MB)
>>Set to Factory successfully.

Moiz Khan · 03-15-2015, 07:53

Code:

  Available Ports:COM1 COM3 COM4 COM5 COM33 COM34 COM35 
    
  Waiting for phone's response, press the Power on the phone.. 
  Ready to read/write again, please remove the power supply clip or battery and then re-loaded it.
  Reset USB device and search it...
  Find USB device:SPRD U2S Diag (COM5), (VID_1782&PID_4D00)
    
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310000]
  FLASH ID: 002C00CB00180000
  Flash Type: SF_N25W128                 
  Size:0x1000000(16MB)
  Reading completed.
  The data has been saved in K:\MOCOR_12B_6531.W13.11_Release_20141219_151451_FullFlash YXTEL C801 05b vol down.bin, size: 16 M.
  Reset USB device and search it...
  Find USB device:SPRD U2S Diag (COM5), (VID_1782&PID_4D00)
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310000]
  FLASH ID: 002C00CB00180000
  Flash Type: SF_N25W128                 
  Size:0x1000000(16MB)
>>Set to Factory successfully.

Moiz Khan · 03-15-2015, 07:54

Code:

  Detection initiated...
  Vcc: 10
  Gnd: 1 4
  Analyzing D+ and D-...
  D+ = 9, D- = 8
  Detection D+/D- with 1.75 seconds.
  Continue to detect BOOT pin...
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
  BOOT(Pull Down) = 6
  Setting...
  Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
  Pinouts setting complete!
    
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310000]
  FLASH ID: 00C8006000160000
  Flash Type:[GD]  25LG32bWL
  Size:0x400000(4MB)
  Reading completed.
  The data has been saved in D:\FLASH FILES\SC6531\MOCOR_12C.W13.04.05_Release_20150224_194813_FullFlash Videocon V1417 {SC6531 [GD] 25LG32bWL} Cable - 12c.bin, size: 4 M.
  Detection initiated...
  Vcc: 10
  Gnd: 1 4
  Analyzing D+ and D-...
  D+ = 9, D- = 8
  Detection D+/D- with 1.30 seconds.
  Continue to detect BOOT pin...
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
  BOOT(Pull Down) = 6
  Setting...
  Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
  Pinouts setting complete!
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310000]
  FLASH ID: 00C8006000160000
  Flash Type:[GD]  25LG32bWL
  Size:0x400000(4MB)
  Set to Factory successfully.

Moiz Khan · 03-15-2015, 07:55

Code:

  Detection initiated...
  Vcc: null
  Gnd: 5
  Analyzing D+ and D-...
  D+ = 3, D- = 2
  Detection D+/D- with 1.33 seconds.
  Continue to detect BOOT pin...
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
  UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
  Setting...
  Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
  Pinouts setting complete!
    
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310001]
  FLASH ID: 00C8006000160000
  Flash Type: SF_GD25LQ32                
  Size:0x400000(4MB)
  Reading completed.
  The data has been saved in D:\FLASH FILES\SC6531\Videocon V1398 {SC6531 [SF_GD25LQ32]} Cable - 05b press 0 button.bin, size: 4 M.
  Screen Lock input order:
    ¢Ù ¢Ú ¢Û
    ¢Ü ¢Ý ¢Þ
    ¢ß ¢à ¢á
   
  Software has two ways to find password, it may have different results to click button again.
  Looking for passwords,please wait...
  [Phone Lock]  0000
  [Phone Lock]  725482
  [Phone Lock]  1234
>>Looking for passwords complete.

Moiz Khan · 03-15-2015, 07:56

Code:

  Detection initiated...
  Vcc: null
  Gnd: 5
  Analyzing D+ and D-...
  D+ = 3, D- = 2
  Analyzing USB device, please wait...
  Find USB device:SCI USB2Serial (COM165), (VID_1782&PID_4D00)
    
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310001]
  FLASH ID: 00C8006000180000
  Size:0x1000000(16MB)
  Reading completed.
  The data has been saved in C:\Documents and Settings\Shanu\Desktop\Spice_M5918_IND_Ver9.0_Build INfo140613_1553     _20141130_185146_FullFlash.bin, size: 16 M.
  Detection initiated...
  Vcc: null
  Gnd: 5
  Analyzing D+ and D-...
  D+ = 3, D- = 2
  Analyzing USB device, please wait...
  Find USB device:SCI USB2Serial (COM165), (VID_1782&PID_4D00)
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310001]
  FLASH ID: 00C8006000180000
  Size:0x1000000(16MB)
>>Set to Factory successfully.

Moiz Khan · 03-15-2015, 07:58

Code:

  Detection initiated...
  Vcc: null
  Gnd: 5
  Analyzing D+ and D-...
  D+ = 3, D- = 2
  Detection D+/D- with 1.56 seconds.
  Continue to detect BOOT pin...
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
  UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
  Setting...
  Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
  Pinouts setting complete!
    
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310000]
  FLASH ID: 00EF004000160000
  Flash Type:[WinBond]  W25Q32BV
  Size:0x400000(4MB)
  Reading completed.
  The data has been saved in C:\Documents and Settings\Mkhan\Desktop\_20141231_145516_FullFlash.bin, size: 4 M.
  Detection initiated...
  Vcc: null
  Gnd: 5
  Analyzing D+ and D-...
  D+ = 3, D- = 2
  Detection D+/D- with 1.80 seconds.
  Continue to detect BOOT pin...
  Found [SPD] USB device: SCI USB2Serial,(VID_1782&PID_4D00)
  UsbVcc(VCC) = 1 10, BOOT(Pull Down) = 4
  Setting...
  Find USB device:SCI USB2Serial (COM56), (VID_1782&PID_4D00)
  Pinouts setting complete!
    
  Internal version: SPRD3
  Boot downloaded.
  Start boot please wait a moment....
  Spreadtrum Boot Block version 1.2
  CPU TYPE:SC6531 [65310000]
  FLASH ID: 00EF004000160000
  Flash Type:[WinBond]  W25Q32BV
  Size:0x400000(4MB)
>>Set to Factory successfully.

03-15-2015, 07:40	#1 (permalink)
Moiz Khan No Life Poster Join Date: Jul 2007 Location: India Posts: 2,683 Member: 557473 Status: Offline Sonork: 100.1627500 Thanks Meter: 2,284	Repairing SC6531 With Volcano is So Easy That I Wish All Faulty Mobiles have This CPU Repairing SC6531/SC6531D/SC6531DA With Volcano is So Easy That I Wish All Incoming Faulty Mobiles Were SC6531 Till Date I have Repaired More Than 5000 SC6531 Handsets, Only 2-3 of them I had returned to Customer Just Because Of Bad Flash Files, Otherwise All Handsets were revived Successfully. Only Following Below Given Universal Method (Most Of You Know This Very Well) : * READ FLASH FILE * LOAD/SELECT YOUR READED FLASH FILE * DO FORMAT (Check Now if phone got ok) If Not Got Ok, then * WRITE FLASH FILE * AGAIN DO FORMAT (Check Now phone got ok) NOTE : Best Way to check Phone is On Volcano Eagle Eye. OR Insert Full Charged Battery & Press Power Button for atleast 1minute I'll Post Many Logs Here To Show You All People That Volcano is Not A Useless Device As Many Of You People Always Blame. Please Check & Observe All Logs Carefully. If You Want Flash Files, You can Find It in Volcano Flash Files Section Or On My Support. bR. Moiz Khan (Volcano Team)