AutoIgnition Cable for CXnn - GSM-Forum

ednacell · 08-22-2005, 18:52

AutoIgnition Cable for All CXNN that can be used with Papua`s software.

systemworm · 08-24-2005, 12:10

Quote:

Originally Posted by ********

AutoIgnition Cable for All CXNN that can be used with Papua`s software.

10x for the cable schema.I will make it and afterwards test it.
Regards

cartuchobahia · 09-02-2005, 16:53

Can you give me more information? Is it made with the charger? It got's any conection to ground? Any resistence? Do we have to make something with the power on contacts indicated on the picture?
thanks

fofesz · 09-03-2005, 09:51

there is red power on jumper, this is NOT autoignition cable
just testpoint connected to GND

fontelense · 09-03-2005, 10:29

Yes, this is not autoignition, only one way of making the testpoint. Using this you still have to short the keypad pins in red line to make the ignition.
There is a scheme going around that works, it uses a PL2303 USB to COM cable and a MAX232 with inverted signal to make the ignition.

Best regards

ednacell · 09-03-2005, 14:56

True True Blue, Here It Is For You..........

Chris02 · 09-03-2005, 17:02

Quote:

Originally Posted by ********

True True Blue, Here It Is For You..........

Very bad to add the own pic/brand to a stolen pic!

Yasumi · 09-03-2005, 18:13

Quote:

Originally Posted by ********

True True Blue, Here It Is For You..........

Thanks !
But What's the Diot from DTR ??
Should be 1N4148 or ...............???

ednacell · 09-03-2005, 18:25

Quote:

Originally Posted by Chris02

Very bad to add the own pic/brand to a stolen pic!

Then I should have put circuit modified by ********. Can you post the so-called stolen pic (with same Circuit layout with same pin-out). Easy to say stolen with no prove. I did not think you can provide link to see the same pinout for a C5x serial com port AutoIgnition Cable.

With all do respect, the only AutoIgnition Cable RS232, I found was for Older Seimens phones like A40, A50 etc..

Chris02 · 09-04-2005, 01:21

My respect you changed the PinOuts!

I think I haven't to say more....

Keni · 10-01-2005, 22:19

Quote:

Originally Posted by fontelense

Yes, this is not autoignition, only one way of making the testpoint. Using this you still have to short the keypad pins in red line to make the ignition.
There is a scheme going around that works, it uses a PL2303 USB to COM cable and a MAX232 with inverted signal to make the ignition.

Best regards

hi,

Yes it's correct!
I hade the manual drowed picture from russia , but I lost it.
Please sombody to attach it!

Thanks in advance

Keni

rango · 10-22-2006, 15:44

Here it is, siemens autoignition cable shematic
tester and working 100%

You can use any data cable with pl2303 chip and add one max232, and voila!

Best regards...

topman52373 · 11-08-2006, 19:56

what are auto-ignition for?

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
SST Autoignition cable	SST-GSM	SST-Dongle	50	10-11-2006 22:23
..SST Autoignition Cable Schematic...	bayram	SST-Dongle	1	12-07-2005 13:58
Data cable for BOSCH 607/738 and Data cable for BOSCH 909	lion108h	Various	3	10-27-2005 13:55
is cable for c2200 same as cable for lg 7050 orl g81xx	ashvin	Redbox	0	07-13-2005 08:03
I neeD urgently of cable shematics for external power supply 9v for cable for OTE 3X	doky	Alcatel & TCL Old Models	0	02-15-2002 07:39

09-02-2005, 16:53	#3 (permalink)
cartuchobahia No Life Poster Join Date: Aug 2005 Location: Salvador - Bahia - Brazil Age: 48 Posts: 840 Member: 172567 Status: Offline Thanks Meter: 90	Can you give me more information? Is it made with the charger? It got's any conection to ground? Any resistence? Do we have to make something with the power on contacts indicated on the picture? thanks

09-03-2005, 09:51	#4 (permalink)
fofesz No Life Poster Join Date: Feb 2003 Location: Hungary Age: 40 Posts: 524 Member: 22869 Status: Offline Thanks Meter: 132	there is red power on jumper, this is NOT autoignition cable just testpoint connected to GND

09-03-2005, 10:29	#5 (permalink)
fontelense No Life Poster Join Date: Sep 2001 Location: Portugal Age: 50 Posts: 618 Member: 6358 Status: Offline Thanks Meter: 10	Yes, this is not autoignition, only one way of making the testpoint. Using this you still have to short the keypad pins in red line to make the ignition. There is a scheme going around that works, it uses a PL2303 USB to COM cable and a MAX232 with inverted signal to make the ignition. Best regards

09-04-2005, 01:21	#10 (permalink)
Chris02 No Life Poster Join Date: Oct 2003 Location: Germany Age: 37 Posts: 5,196 Member: 41076 Status: Offline Thanks Meter: 53	My respect you changed the PinOuts! I think I haven't to say more....

11-08-2006, 19:56	#13 (permalink)
topman52373 Junior Member Join Date: Jun 2005 Age: 50 Posts: 25 Member: 150899 Status: Offline Thanks Meter: 3	what are auto-ignition for?