GT-I9300 Unbrick SD Card cloned..! hi to all.. nowadays.. we can find a bin called "GT_I9300_unbrick_sdcard_head.bin" that can be cloned via linux. but.. unfortunately can't find a windows based cloning method. but have found a cloning prog called HDDRAW Copy . i appreciate if anyone can create a compressed image of his I9300 unbrick sdcard from this tool. so..we all can repair dead boot of i9300 without a working phone. thanks nd regards.. |
Finally.. have managed to create an Unbrick SD image.. here's a full dump of 4GB card, first completely cleaned, and then flashed with unbricking S-Boot. * download this tiny i9300.7z file.. (883kb). * extract using 7zip.. (beware, file inside archive is 4GB big). * use HDDRawCopy from previous post to burn i9300.img (3.72GB) to a 4gb SD. regards.. |
is this work by any one..................... |
19.4.2013. 18:18:12 19.4.2013. 18:18:12 HDD Raw Copy Tool 1.02; HDDGURU: Laptop and Desktop Hard Disk Drives, Tests, Software, Firmware, Tools, Data Recovery, HDD Repair 19.4.2013. 18:18:12 19.4.2013. 18:18:12 * * * * * IMPORTANT: DURING THE DUPLICATION PROCESS 19.4.2013. 18:18:12 ALL DATA ON TARGET WILL BE IRREVERSIBLY OVERWRITTEN! 19.4.2013. 18:18:12 19.4.2013. 18:18:12 Source: [0] RAW i9300.img [3995,07 MB] 19.4.2013. 18:18:12 Target: [2] Generic STORAGE DEVICE 0272 [3965,19 MB] 19.4.2013. 18:18:17 Locking device... 19.4.2013. 18:18:17 Copying... 19.4.2013. 18:35:59 Write Error occurred at offset 3,964,600,320 (23) 19.4.2013. 18:35:59 Cannot write to target, aborting... 19.4.2013. 18:35:59 Average speed: 3,7 MB/s 19.4.2013. 18:35:59 Operation terminated at offset 3,964,600,320 LBA 7,743,360 |
Quote:
|
I found the problem with card cloning, this img file is larger than 4gb sd card:) P.S. thanks anyway |
viper gsm how u solve it thanks |
i used 8gb sd card ( or 16gb ) but didn't managed to revive my i9300, nothing happens when i press power on and disconnect shortenning after 3-6 seconds... LCD remains black |
Quote:
|
for me,screen comes on,but sd card download fail |
5/23/2013 7:17:07 PM ALL DATA ON TARGET WILL BE IRREVERSIBLY OVERWRITTEN! 5/23/2013 7:17:07 PM 5/23/2013 7:17:07 PM Source: [0] RAW i9300.img [3995.07 MB] 5/23/2013 7:17:07 PM Target: [2] ChipsBnk Flash Disk 4082 [7948.2 MB] 5/23/2013 7:17:11 PM Locking device... 5/23/2013 7:17:12 PM Copying... 5/23/2013 7:27:46 PM Average speed: 6.3 MB/s 5/23/2013 7:27:46 PM Task complete. not working |
anyone successful unbrick i9300 with this sd card clone method ? |
Quote:
Best special thinks at iqballk for previous post and solution.... so..we all can repair dead boot of i9300 without a working phone. |
How to recover S3 I9300 dead boot I tested and it work fine for me The things you will need: First , to make GT-I9300 Unbrick SD Card cloned i used the method of iqballk ; * download this tiny i9300.7z file.. (883kb). * extract using 7zip... * use HDDRAW Copy to burn i9300.img (3.72GB) to a 4gb SD card. For me;i used 4GB SD card completely cleaned After successful burn sd card clone ; Disassemble the S3 I9300 Dead http://i175.photobucket.com/albums/w...ps0188b085.png Insert SD card cloned to PBAhttp://i175.photobucket.com/albums/w...psbc15c750.png Connect the PBA with rj45 c3300K (C3303K UART Auto Ignition! it's use to repair I9300 imei) and connect rj45 to the box (for me i connected to riff box rj45) insert battery Short R313 resistance.(HQ uses tweezers to short the resistance) http://i175.photobucket.com/albums/w...ps1f552596.png http://i175.photobucket.com/albums/w...pse6da1112.png Turn on the PBA, and REMOVE THE SHORT between 3 to 6 seconds from turning on the PBA. After approximately 5 seconds, you can see message on the LCD boot recovery was succeeded http://i175.photobucket.com/albums/w...ps53b66405.png Turn off the pba, and remove SD Card. Assemble the phone, and enter download mode.Download Full S/W including PIT, PDA, CSC and PHONE with ODIN. Here is how i repaired my S3 I9300 without normal I9300 |
will it work with other box's Will this work with any other box like ns pro or z3x with rj45 cable uart connected to box ? Thanks |
All times are GMT +1. The time now is 10:48. |
vBulletin Optimisation provided by
vB Optimise (Pro) -
vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
- GSM Hosting Ltd. - 1999-2023 -