dead se k800i - GSM-Forum

Arkadius1984 · 06-16-2008, 13:32

Hi, I have a problem with my k800i.

My girlfriend swaped sim cards, and after that, the phone doesn't want to turn on, instead of that only red light comes from where the ir port is located. I've red about this a lot on the web, but all adviced solutions have failed. I was using xs++, setool, with combination of c button, and nothong happens. However when I'm using setool with combination of 2+5 it indicates bootrom mode, and when I'm tryin' to reflash it, whole process stops in particular moment. I want to add, that I know how to do reflash, because in the past I unlocked and debranded obout 30 se, with using xs++ and setool. I would appreciate some good advice. Obviously I want to do this absoultely for free, cause the phone itself is not worth to spend any money an it

below I'm adding complete log from reflashing trials. Arkadius.

Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors

if you like LITE edition - please visit www.setool.net and buy FULL.

ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35731501472036 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok

CID52 BYPASS PROCEDURE STARTED
Processing part1...
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
Processing part2...
Processing part3....
BOOTROM MODE DETECTED
OTP LOCKED:1 CID:51 PAF:1 IMEI:35731501472036 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok

REMOVE CABLE FROM PHONE
REMOVE BATTERY FROM PHONE, THEN INSERT IT BACK
THEN PRESS "READY"

HOLD "C" BUTTON AND ATTACH PHONE

CID52 BYPASS PROCEDURE FINISHED

ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Trying to launch embedded bootloader...
embedded flashloader not responds !
Elapsed:591 secs.

Arkadius1984 · 06-16-2008, 13:46

I tried to repair erom with setool, but i get the fatal error - see log

ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:897E
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:35731501472036 CERT:N/A
FLASH CID:52 COLOR:RED
no ack during gdfs_readvar !
Can't read SCRC unit
Elapsed:84 secs.
ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35731501472036 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
loader startup: executed
CSloader refused to start GDFS services,error is:29
failed, that is fatal
Elapsed:6 secs.

stanner_austin · 06-16-2008, 15:17

@Arkadius1984
hello and welcome to gsmhosting.

first of all as i see on your first post. you used bypass that's wrong .
second you have cid52 in flash and cid51 as otp so you don't need any erom update.
three in case you want to flash normally you just have to use NORMAL FLASH MODE not RECOVERY MODE.
i like to tell you to read one this thread F.A.Q About Sony Ericsson Phones

now for basic if you tell me when you insert battery and press C and insert usb cable
its ask you flash mode driver ?
if not its already installed or even detect at pc?
if not detect even means big problem.
if detected install flash mode driver.
if already installed use setool and press indentify and paste here.

Arkadius1984 · 06-16-2008, 15:50

Than you for fast response

I shall start of that when I'm plugging the phone , (it means, I'm reinserting the battery, plugging usb cable to laptop, and to the phone) when I hold c button, nothing happens, pc doesn't detect flashmode at all. It only detects my k800 in recovery mode, 2+5. And that is the biggest problem. I tried reinstall flash drivers, but effect is the same. So I can't do identyfying with flach mode, with c button pressed, only with recovery mode. Is there any way to bring the normal flash mode back?

stanner_austin · 06-16-2008, 15:56

Quote:

Originally Posted by Arkadius1984

Than you for fast response

I shall start of that when I'm plugging the phone , (it means, I'm reinserting the battery, plugging usb cable to laptop, and to the phone) when I hold c button, nothing happens, pc doesn't detect flashmode at all. It only detects my k800 in recovery mode, 2+5. And that is the biggest problem. I tried reinstall flash drivers, but effect is the same. So I can't do identyfying with flach mode, with c button pressed, only with recovery mode. Is there any way to bring the normal flash mode back?

try this in case if you do wrong.
remove battery from phone.
remove usb cable from phone.
insert battery to phone.
press C at phone.
keep pressed C at phone.
insert DCU60 keep holding C when ur inserting dcu60.
now see if still same
i can't help.

you must visit any repair center to fix this phone.

Arkadius1984 · 06-16-2008, 16:10

Thank U for fast response.

I disabled security bypass mode, but the effect is the same.
When I plug my k800 to the laptop with normal flash mode (c pressed) it does nothing. I reinstalled flash drivers twice, and still nothing. When I plug it in recovery mode (2+5) it detects my phone, but when I press Identyfy i get something like this:

Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors

if you like LITE edition - please visit www.setool.net and buy FULL.

ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:897E
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:35731501472036 CERT:N/A
FLASH CID:52 COLOR:RED
no ack during gdfs_readvar !
Can't read SCRC unit
Elapsed:88 secs.

is there any way to bring normal flash mode back to work????

stanner_austin · 06-16-2008, 16:31

no way
its have some hardware problem 90% i think
or
its have erom damaged in software 10% i think.

best way to solve go to sony ericsson service center or any local repair shop.
sorry but i can't help more no way as i think for free at last.

westgold · 06-16-2008, 16:35

reading the FAQ in the setool support forum will guide you how to repair the problem

Arkadius1984 · 06-16-2008, 16:37

Thank U for fast response.

I disabled security bypass mode, but the effect is the same.
When I plug my k800 to the laptop with normal flash mode (c pressed) it does nothing. I reinstalled flash drivers twice, and still nothing. When I plug it in recovery mode (2+5) it detects my phone, but when I press Identyfy i get something like this:

Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors

if you like LITE edition - please visit www.setool.net and buy FULL.

ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Flash ID check:897E
Flash props sent ok
OTP LOCKED:1 CID:51 PAF:1 IMEI:35731501472036 CERT:N/A
FLASH CID:52 COLOR:RED
no ack during gdfs_readvar !
Can't read SCRC unit
Elapsed:88 secs.

is there any way to bring normal flash mode back to work????

stanner_austin · 06-16-2008, 17:12

Quote:

Originally Posted by westgold

reading The Faq In The Setool Support Forum Will Guide You How To Repair The Problem

do Not Spam If You Don't Know.

Mittons · 06-17-2008, 11:39

try using seus as last resort, but may have to use emergency mode (2+5) before connect..

i have used for w880 with similar issue and fixed. but upgraded to cid53, still available to unlock with new bypass procedure so all good.

Nurettin Duman · 06-17-2008, 11:48

Quote:

Originally Posted by Arkadius1984

Hi, I have a problem with my k800i.

My girlfriend swaped sim cards, and after that, the phone doesn't want to turn on, instead of that only red light comes from where the ir port is located. I've red about this a lot on the web, but all adviced solutions have failed. I was using xs++, setool, with combination of c button, and nothong happens. However when I'm using setool with combination of 2+5 it indicates bootrom mode, and when I'm tryin' to reflash it, whole process stops in particular moment. I want to add, that I know how to do reflash, because in the past I unlocked and debranded obout 30 se, with using xs++ and setool. I would appreciate some good advice. Obviously I want to do this absoultely for free, cause the phone itself is not worth to spend any money an it

below I'm adding complete log from reflashing trials. Arkadius.

Welcome to SEtool2 ( LITE edition ) v 1.11
supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52
Loaded 51 flash descriptors

if you like LITE edition - please visit www.setool.net and buy FULL.

ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
OTP LOCKED:1 CID:51 PAF:1 IMEI:35731501472036 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok

CID52 BYPASS PROCEDURE STARTED
Processing part1...
CSloader version:
070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009
Processing part2...
Processing part3....
BOOTROM MODE DETECTED
OTP LOCKED:1 CID:51 PAF:1 IMEI:35731501472036 CERT:N/A
FLASH CID:52 COLOR:RED
LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005
Flash ID check:897E
Flash props sent ok

REMOVE CABLE FROM PHONE
REMOVE BATTERY FROM PHONE, THEN INSERT IT BACK
THEN PRESS "READY"

HOLD "C" BUTTON AND ATTACH PHONE

CID52 BYPASS PROCEDURE FINISHED

ChipID:9900,EMP protocol:0301
BOOTROM MODE DETECTED
Speed:921600
Trying to launch embedded bootloader...
embedded flashloader not responds !
Elapsed:591 secs.

its have some hardware problem 100% think
http://forum.gsmhosting.com/vbb/showthread.php?t=536413

msnv · 09-15-2008, 21:47

I have a problem with my k800i too and adorn prob at 5 step

Step 1
USE OLD VERSION SeTool for example v0.914020

Step 2
Check Settings:
COMPLETE PHONE AFTER FLASH
UNLOCK AFTER FLASH
USE SERVER FOR CSCA UNLOCK/FLASH
ENABLE ALTERNATIVE SECURITY BYPASS
DO FULL UNLOCK INSTEAD OF USERCODE RESET

Step 3
Add files:
.......
Step 4
....Copy Files to Rest Folder....

... and...

Step 5
Click Flash

Download ...
see...
http://forum.gsmhosting.com/vbb/showthread.php?t=595698

Professional · 09-15-2008, 21:58

Dear bro,
No worry, Use com cable instead of dcu60 and make sure ur battery is fully charged. If unsuccessful please post logs.

Good Luck

06-16-2008, 13:32	#1 (permalink)
Arkadius1984 Junior Member Join Date: Jun 2008 Posts: 15 Member: 792471 Status: Offline Thanks Meter: 1	dead se k800i Hi, I have a problem with my k800i. My girlfriend swaped sim cards, and after that, the phone doesn't want to turn on, instead of that only red light comes from where the ir port is located. I've red about this a lot on the web, but all adviced solutions have failed. I was using xs++, setool, with combination of c button, and nothong happens. However when I'm using setool with combination of 2+5 it indicates bootrom mode, and when I'm tryin' to reflash it, whole process stops in particular moment. I want to add, that I know how to do reflash, because in the past I unlocked and debranded obout 30 se, with using xs++ and setool. I would appreciate some good advice. Obviously I want to do this absoultely for free, cause the phone itself is not worth to spend any money an it below I'm adding complete log from reflashing trials. Arkadius. Welcome to SEtool2 ( LITE edition ) v 1.11 supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52 Loaded 51 flash descriptors if you like LITE edition - please visit www.setool.net and buy FULL. ChipID:9900,EMP protocol:0301 BOOTROM MODE DETECTED Speed:921600 OTP LOCKED:1 CID:51 PAF:1 IMEI:35731501472036 CERT:N/A FLASH CID:52 COLOR:RED LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005 Flash ID check:897E Flash props sent ok CID52 BYPASS PROCEDURE STARTED Processing part1... CSloader version: 070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009 Processing part2... Processing part3.... BOOTROM MODE DETECTED OTP LOCKED:1 CID:51 PAF:1 IMEI:35731501472036 CERT:N/A FLASH CID:52 COLOR:RED LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005 Flash ID check:897E Flash props sent ok REMOVE CABLE FROM PHONE REMOVE BATTERY FROM PHONE, THEN INSERT IT BACK THEN PRESS "READY" HOLD "C" BUTTON AND ATTACH PHONE CID52 BYPASS PROCEDURE FINISHED ChipID:9900,EMP protocol:0301 BOOTROM MODE DETECTED Speed:921600 Trying to launch embedded bootloader... embedded flashloader not responds ! Elapsed:591 secs.

06-17-2008, 11:39	#11 (permalink)
Mittons Insane Poster Join Date: Nov 2004 Location: Sydney, Australia Posts: 62 Member: 93516 Status: Offline Thanks Meter: 7	no gdfs try using seus as last resort, but may have to use emergency mode (2+5) before connect.. i have used for w880 with similar issue and fixed. but upgraded to cid53, still available to unlock with new bypass procedure so all good.

09-15-2008, 21:47	#13 (permalink)
msnv Freak Poster Join Date: Jan 2008 Location: Belgrade - Serbia Age: 45 Posts: 181 Member: 669559 Status: Offline Thanks Meter: 157	Full Flash K800 CID52 with SeTool-by msnv I have a problem with my k800i too and adorn prob at 5 step Step 1 USE OLD VERSION SeTool for example v0.914020 Step 2 Check Settings: COMPLETE PHONE AFTER FLASH UNLOCK AFTER FLASH USE SERVER FOR CSCA UNLOCK/FLASH ENABLE ALTERNATIVE SECURITY BYPASS DO FULL UNLOCK INSTEAD OF USERCODE RESET Step 3 Add files: ....... Step 4 ....Copy Files to Rest Folder.... ... and... Step 5 Click Flash Download ... see... http://forum.gsmhosting.com/vbb/showthread.php?t=595698

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
se k800i dead	lalasdj	KULANKENDI Server	3	07-12-2007 05:03
se k800i dead	ryaz1993.	Universalbox	3	03-05-2007 20:50
SE K800i DEAD AFTER FALLING	fusion007	Sony Ericsson Hardware Repair	0	12-21-2006 23:35
SE K800i dead????	Syri	Sony Ericsson	4	09-25-2006 17:37
se k800i	arturo1976	Universalbox	4	08-02-2006 13:58

06-16-2008, 13:46	#2 (permalink)
Arkadius1984 Junior Member Join Date: Jun 2008 Posts: 15 Member: 792471 Status: Offline Thanks Meter: 1	I tried to repair erom with setool, but i get the fatal error - see log ChipID:9900,EMP protocol:0301 BOOTROM MODE DETECTED Speed:921600 Flash ID check:897E Flash props sent ok OTP LOCKED:1 CID:51 PAF:1 IMEI:35731501472036 CERT:N/A FLASH CID:52 COLOR:RED no ack during gdfs_readvar ! Can't read SCRC unit Elapsed:84 secs. ChipID:9900,EMP protocol:0301 BOOTROM MODE DETECTED Speed:921600 OTP LOCKED:1 CID:51 PAF:1 IMEI:35731501472036 CERT:N/A FLASH CID:52 COLOR:RED LDR:061201 1314 HANCXC1329129_DB2020_FLASHLOADER_R2A005 Flash ID check:897E Flash props sent ok CSloader version: 070410 1557 HANCXC1250562_DB2020_CSLOADER_R3A009 loader startup: executed CSloader refused to start GDFS services,error is:29 failed, that is fatal Elapsed:6 secs.

06-16-2008, 15:17	#3 (permalink)
stanner_austin No Life Poster Join Date: Jan 2004 Location: Unknown Age: 39 Posts: 9,227 Member: 49752 Status: Offline Sonork: QQ:1474246528 Thanks Meter: 6,085	@Arkadius1984 hello and welcome to gsmhosting. first of all as i see on your first post. you used bypass that's wrong . second you have cid52 in flash and cid51 as otp so you don't need any erom update. three in case you want to flash normally you just have to use NORMAL FLASH MODE not RECOVERY MODE. i like to tell you to read one this thread F.A.Q About Sony Ericsson Phones now for basic if you tell me when you insert battery and press C and insert usb cable its ask you flash mode driver ? if not its already installed or even detect at pc? if not detect even means big problem. if detected install flash mode driver. if already installed use setool and press indentify and paste here.

06-16-2008, 15:50	#4 (permalink)
Arkadius1984 Junior Member Join Date: Jun 2008 Posts: 15 Member: 792471 Status: Offline Thanks Meter: 1	Than you for fast response I shall start of that when I'm plugging the phone , (it means, I'm reinserting the battery, plugging usb cable to laptop, and to the phone) when I hold c button, nothing happens, pc doesn't detect flashmode at all. It only detects my k800 in recovery mode, 2+5. And that is the biggest problem. I tried reinstall flash drivers, but effect is the same. So I can't do identyfying with flach mode, with c button pressed, only with recovery mode. Is there any way to bring the normal flash mode back?

06-16-2008, 16:10	#6 (permalink)
Arkadius1984 Junior Member Join Date: Jun 2008 Posts: 15 Member: 792471 Status: Offline Thanks Meter: 1	Thank U for fast response. I disabled security bypass mode, but the effect is the same. When I plug my k800 to the laptop with normal flash mode (c pressed) it does nothing. I reinstalled flash drivers twice, and still nothing. When I plug it in recovery mode (2+5) it detects my phone, but when I press Identyfy i get something like this: Welcome to SEtool2 ( LITE edition ) v 1.11 supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52 Loaded 51 flash descriptors if you like LITE edition - please visit www.setool.net and buy FULL. ChipID:9900,EMP protocol:0301 BOOTROM MODE DETECTED Speed:921600 Flash ID check:897E Flash props sent ok OTP LOCKED:1 CID:51 PAF:1 IMEI:35731501472036 CERT:N/A FLASH CID:52 COLOR:RED no ack during gdfs_readvar ! Can't read SCRC unit Elapsed:88 secs. is there any way to bring normal flash mode back to work????

06-16-2008, 16:31	#7 (permalink)
stanner_austin No Life Poster Join Date: Jan 2004 Location: Unknown Age: 39 Posts: 9,227 Member: 49752 Status: Offline Sonork: QQ:1474246528 Thanks Meter: 6,085	no way its have some hardware problem 90% i think or its have erom damaged in software 10% i think. best way to solve go to sony ericsson service center or any local repair shop. sorry but i can't help more no way as i think for free at last.

06-16-2008, 16:35	#8 (permalink)
westgold No Life Poster Join Date: Mar 2008 Location: west coast PH Posts: 523 Member: 734668 Status: Offline Thanks Meter: 83	reading the FAQ in the setool support forum will guide you how to repair the problem

06-16-2008, 16:37	#9 (permalink)
Arkadius1984 Junior Member Join Date: Jun 2008 Posts: 15 Member: 792471 Status: Offline Thanks Meter: 1	Thank U for fast response. I disabled security bypass mode, but the effect is the same. When I plug my k800 to the laptop with normal flash mode (c pressed) it does nothing. I reinstalled flash drivers twice, and still nothing. When I plug it in recovery mode (2+5) it detects my phone, but when I press Identyfy i get something like this: Welcome to SEtool2 ( LITE edition ) v 1.11 supported DB2010/DB2012 CID49/50/51/52, DB2020 CID49/51/52 Loaded 51 flash descriptors if you like LITE edition - please visit www.setool.net and buy FULL. ChipID:9900,EMP protocol:0301 BOOTROM MODE DETECTED Speed:921600 Flash ID check:897E Flash props sent ok OTP LOCKED:1 CID:51 PAF:1 IMEI:35731501472036 CERT:N/A FLASH CID:52 COLOR:RED no ack during gdfs_readvar ! Can't read SCRC unit Elapsed:88 secs. is there any way to bring normal flash mode back to work????

09-15-2008, 21:58	#14 (permalink)
Professional Freak Poster Join Date: Oct 2006 Location: UK Posts: 235 Member: 362955 Status: Offline Thanks Meter: 61	Dear bro, No worry, Use com cable instead of dcu60 and make sure ur battery is fully charged. If unsuccessful please post logs. Good Luck