GSM Shop GSM Shop
GSM-Forum  

Welcome to the GSM-Forum forums.

You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features.
Only registered members may post questions, contact other members or search our database of over 8 million posts.

Registration is fast, simple and absolutely free so please - Click to REGISTER!

If you have any problems with the registration process or your account login, please contact contact us .

Go Back   GSM-Forum > Product Support Sections > No More Supported Solutions (Dead Products) > No More Supported H/W Products > xtc2cliP

Closed Thread
 
LinkBack Thread Tools Display Modes
Old 12-08-2015, 11:26   #1 (permalink)
No Life Poster
 
Join Date: Jun 2015
Posts: 6,556
Member: 2416253
Status: Offline
Thanks Meter: 4,163
GUIDE: Direct mode (S-OFF/IMEI/etc) phones with download mode (A9/M9/626/etc)


Dear customers,

Here is an information about how to work with new phones which have "Download mode".

1. What is a "Download mode"?

Download mode is a new service mode introduced since HTC M9. You can flash and service your phone in this mode.

2. How do I get into this mode?

2 ways:

a) While phone is powered OFF, hold VOLUME DOWN and POWER.
b) Connect your phone to PC. Run XTC 2 Tool and press "Download" button in mode selection.

How do I use XTC 2 Clip with these phones?

First, you must connect your XTC 2 Clip to the phone, a connection example can be found here:

http://forum.gsmhosting.com/vbb/f961...ample-1967566/

NOTE! Clip must be connected BEFORE phone is powered ON. If the clip was connected AFTER, then you need to reboot download mode.

M9 in download mode, "SD NOT MOUNTED" = No SD card / XTC 2 Clip connected



M9 in download mode, "GT_CONNECT_FAIL" = XTC 2 Clip connected, but probably you need to repair it



M9 in download mode, no error = XTC 2 Clip connected and everything is ready for operation. You will also see additional options (Factory reset and Check smart SD (note - if the phone is S-OFF you'll see these options even without the clip)



Now, when everything is ready - you can run XTC 2 Tool and open "Direct mode commands" tab:

You can use the buttons from highlighted area (IMEI1/IMEI2/CID/MEID/S-OFF)



Possible errors:

NOT_FIND_SMART_IO - Your clip is not attached.
VERIFY_GET_PATERN_FAIL - Make sure your clip is upgraded and activated. You can also try to repair clip.
DECREASE_CYCLE_FAIL - Please contact us via PM or on skype: xtc2clip

SIM UNLOCK

Unfortunately you cannot unlock phones from direct mode. To remove sim lock, please use "Sprint" tab for Sprint phones and "Special unlock" tab for all other phones.

This guide will be updated!

Last edited by xtc2clip; 12-08-2015 at 16:19.
 
The Following 16 Users Say Thank You to xtc2clip For This Useful Post:
Show/Hide list of the thanked
Old 12-18-2015, 17:49   #2 (permalink)
No Life Poster
 
Join Date: May 2002
Location: TX
Age: 49
Posts: 641
Member: 12427
Status: Offline
Thanks Meter: 78
Could you add some info about error SELECT_APPLET_FAIL?
At first i got GT_CONNECT_FAIL, after repaired, now i get error "SELECT_APPLET_FAIL" (I inserted SD in phone then press download in tool)
 
The Following User Says Thank You to abcchoier For This Useful Post:
Old 12-18-2015, 20:19   #3 (permalink)
No Life Poster
 
Join Date: Jun 2015
Posts: 6,556
Member: 2416253
Status: Offline
Thanks Meter: 4,163
Quote:
Originally Posted by abcchoier View Post
Could you add some info about error SELECT_APPLET_FAIL?
At first i got GT_CONNECT_FAIL, after repaired, now i get error "SELECT_APPLET_FAIL" (I inserted SD in phone then press download in tool)
It's a rare case. Your clip is damaged, contact support with your clip ID please.
 
The Following 3 Users Say Thank You to xtc2clip For This Useful Post:
Show/Hide list of the thanked
Old 02-24-2016, 03:03   #4 (permalink)
Junior Member
 
Join Date: Oct 2015
Posts: 21
Member: 2468157
Status: Offline
Thanks Meter: 6
Hi,

Sending oem clearsimlocktype
... (bootloader) [ERR] Command error !!!
Execution time is 0(ms)
OKAY
Operation finished

Always appear this error, help
 
The Following User Says Thank You to norato001 For This Useful Post:
Old 02-24-2016, 18:17   #5 (permalink)
No Life Poster
 
Join Date: Jun 2015
Posts: 6,556
Member: 2416253
Status: Offline
Thanks Meter: 4,163
Quote:
Originally Posted by norato001 View Post
Hi,

Sending oem clearsimlocktype
... (bootloader) [ERR] Command error !!!
Execution time is 0(ms)
OKAY
Operation finished

Always appear this error, help
Please read button name, and then this manual again, thank you.
 
The Following 2 Users Say Thank You to xtc2clip For This Useful Post:
Closed Thread

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are On
Pingbacks are On
Refbacks are On


 



All times are GMT +1. The time now is 01:40.



Powered by Searchlight © 2024 Axivo Inc.
vBulletin Optimisation provided by vB Optimise (Pro) - vBulletin Mods & Addons Copyright © 2024 DragonByte Technologies Ltd.
- GSM Hosting Ltd. - 1999-2023 -
Page generated in 0.16044 seconds with 8 queries

SEO by vBSEO