3110 ?? - GSM-Forum

YeTi · 08-26-2003, 20:37

Hi,

i have a nokia 3110 that have exceed the 5 atemps to put the code for the 4 lock, i try with koci soft but it cannot open the 4 lock and with dejan program it give an error, so i try with eeprom, i take it out and open the bin with uspu and with lovelas and write it but i still get card not accepted??? how can i clear counter attemp or clear eeprom??

regards

nokiaking · 08-27-2003, 10:20

Quote:

Originally posted by YeTi
Hi,

i have a nokia 3110 that have exceed the 5 atemps to put the code for the 4 lock, i try with koci soft but it cannot open the 4 lock and with dejan program it give an error, so i try with eeprom, i take it out and open the bin with uspu and with lovelas and write it but i still get card not accepted??? how can i clear counter attemp or clear eeprom??

regards

Your 3110 is DCT2, Koci as far as I know never made a program for DCT2 and Dejan has a program that works fine with this phone.

http://users.net.yu/~dejan/download/nk_info.zip

Download this, make Mbus cable and try to use the program to unlock the phone, can be difficult because you have reached 5 attempts.

With USPU or Szamol (old programs) you should be able to modify the E2P.

YeTi · 08-27-2003, 12:01

koci 3.1.2 support dct2 like 3110/8110.. but dont open the 4 lock, i try dejan as you said but i always got packet send error, and with koci i can read the phone...

about eeprom i alrady clean it with uspu but i still got phone blocked..

tks

nokiaking · 08-27-2003, 16:05

Quote:

Originally posted by YeTi
koci 3.1.2 support dct2 like 3110/8110.. but dont open the 4 lock, i try dejan as you said but i always got packet send error, and with koci i can read the phone...

about eeprom i alrady clean it with uspu but i still got phone blocked..

tks

You use 100% Mbus cable? That is important. Look at the schematic Dejan included with the SW, and Dejan SW runs without problems only communication to the phone doesn't work?

And cloning the E2P? Not 100% but parts of it.

YeTi · 08-27-2003, 18:18

i use mbus cable, the program ask for power on phone and then press enter and then i get fatal error...

cloning e2p i already try but got CONTACT SERVICE, any solution?

nokiaking · 08-27-2003, 21:13

If I remember well the E2P has one checksum for the E2P content, just like 5110/6110 series (they have 2 checksums).

Via szamol you should be able to find out where. I have done experiments with the E2P and they were succesfull. I even turned the net monitor on for this type.

Unfortunatelly I can't give you any more details, because I have not captured them.

B.R,

Jim.

08-26-2003, 20:37	#1 (permalink)
YeTi Freak Poster Join Date: Dec 2001 Location: Portugal Posts: 134 Member: 7985 Status: Offline Thanks Meter: 0	3110 ?? Hi, i have a nokia 3110 that have exceed the 5 atemps to put the code for the 4 lock, i try with koci soft but it cannot open the 4 lock and with dejan program it give an error, so i try with eeprom, i take it out and open the bin with uspu and with lovelas and write it but i still get card not accepted??? how can i clear counter attemp or clear eeprom?? regards

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
3110,3110,6300 restart pro after flash.......100% ok tested by mr many time	mmmfaruk	Nokia Hardware & Hardware Repair	2	01-26-2010 12:11
HOW UNLOCK 3110 ?	igor_m	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	08-19-2000 17:37
Netmonitor Software for 3110?	Joko	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	06-14-1999 11:57
3110 Lock clear on eeprom ...	sidcho	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	0	06-04-1999 00:35

08-27-2003, 12:01	#3 (permalink)
YeTi Freak Poster Join Date: Dec 2001 Location: Portugal Posts: 134 Member: 7985 Status: Offline Thanks Meter: 0	koci 3.1.2 support dct2 like 3110/8110.. but dont open the 4 lock, i try dejan as you said but i always got packet send error, and with koci i can read the phone... about eeprom i alrady clean it with uspu but i still got phone blocked.. tks

08-27-2003, 18:18	#5 (permalink)
YeTi Freak Poster Join Date: Dec 2001 Location: Portugal Posts: 134 Member: 7985 Status: Offline Thanks Meter: 0	i use mbus cable, the program ask for power on phone and then press enter and then i get fatal error... cloning e2p i already try but got CONTACT SERVICE, any solution?

08-27-2003, 21:13	#6 (permalink)
nokiaking Freak Poster Join Date: Sep 1999 Location: EU Posts: 179 Member: 477 Status: Offline Thanks Meter: 1	If I remember well the E2P has one checksum for the E2P content, just like 5110/6110 series (they have 2 checksums). Via szamol you should be able to find out where. I have done experiments with the E2P and they were succesfull. I even turned the net monitor on for this type. Unfortunatelly I can't give you any more details, because I have not captured them. B.R, Jim.