(3410) Cant detect com port - GSM-Forum

sikH · 01-07-2004, 17:50

ok, well i ordered a Data Kabel this time for nokia 3410 and 7110, i start with that i put the sim card in the mobile (3410) then i put in the "thing" alongside the battery, try to turn it on and it works, so far so good, the madness starts when im on my way to program, ive used two programs so far NokTool18 kNok-Pheonix it says com2 is not detected, com3 not detected etc then it says phone not found, i dont know what im doing wrong but please someone help me .. and please read my post about the dead 7110 ( my 7110 dead )

THX!

drpavlov · 01-08-2004, 01:57

dead 7110 done

the next problem:
To unlock, You need an MBUS cable. you can recognize it by on the connector there is a little switch, but you can test it with logomanager too. connect the cable to phone, turn on phone, wait a few sec, plug the cable into the PC, wait a few sec, and in noktool 1.8Rolis from setup menu choose auto setup.

if the phone cannot be found, clean the connector pads on the phone, but if you want to operate with Mbus, the phone ALWAYS has to be SWITCHED ON.
regards,
Pavlov

ejvital · 01-09-2004, 11:17

you must change ur port in ur config its either com2 or com1 or not clean the contact of ur cable and in ur phone...

i hope it works

alex-andro · 01-09-2004, 11:42

check cable !

tical · 01-14-2004, 10:12

Rolis 1.8 does not detect my 3310, after i connected it, it seaches through the ports and says Phone not found. it there any special tips to connect the cable.

tical · 01-15-2004, 09:00

I discovered my problem. be sure to remove foam/sponge from around contacts on cable. It then worked

01-07-2004, 17:50	#1 (permalink)
sikH Junior Member Join Date: Dec 2003 Age: 34 Posts: 5 Member: 47891 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	(3410) Cant detect com port ok, well i ordered a Data Kabel this time for nokia 3410 and 7110, i start with that i put the sim card in the mobile (3410) then i put in the "thing" alongside the battery, try to turn it on and it works, so far so good, the madness starts when im on my way to program, ive used two programs so far NokTool18 kNok-Pheonix it says com2 is not detected, com3 not detected etc then it says phone not found, i dont know what im doing wrong but please someone help me .. and please read my post about the dead 7110 ( my 7110 dead ) THX!

01-14-2004, 10:12	#5 (permalink)
tical No Life Poster Join Date: Nov 2003 Location: Americas Age: 33 Posts: 2,101 Member: 43802 Status: Offline Thanks: 3 Thanked 30 Times in 23 Posts	Must a Sim card be in the phone when unlocking ? Rolis 1.8 does not detect my 3310, after i connected it, it seaches through the ports and says Phone not found. it there any special tips to connect the cable.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
thread	Thread Starter	Forum	Replies	Last Post
philips module cant detect com port	denisirias	Multi-Box	3	03-04-2010 08:55
cannot detect com port when using SECBOX	preshaust	Cruiser Suite	10	09-11-2007 20:04
computer turn bluescreen when auto detect com ports	mccm	Cruiser Suite	11	01-18-2007 11:16
nsbox , cant open com port	TRABEL	NSPRO	9	02-08-2006 20:19
Unlocking Gx25 Cant Open Com Port	tubby67	Sharp	6	05-02-2005 22:37

01-08-2004, 01:57	#2 (permalink)
drpavlov Freak Poster Join Date: Apr 2001 Location: Hungary Posts: 193 Member: 3969 Status: Offline Thanks: 0 Thanked 9 Times in 9 Posts	dead 7110 done the next problem: To unlock, You need an MBUS cable. you can recognize it by on the connector there is a little switch, but you can test it with logomanager too. connect the cable to phone, turn on phone, wait a few sec, plug the cable into the PC, wait a few sec, and in noktool 1.8Rolis from setup menu choose auto setup. if the phone cannot be found, clean the connector pads on the phone, but if you want to operate with Mbus, the phone ALWAYS has to be SWITCHED ON. regards, Pavlov

01-09-2004, 11:17	#3 (permalink)
ejvital Junior Member Join Date: Jan 2004 Age: 36 Posts: 39 Member: 48489 Status: Offline Thanks: 0 Thanked 2 Times in 1 Post	you must change ur port in ur config its either com2 or com1 or not clean the contact of ur cable and in ur phone... i hope it works

01-09-2004, 11:42	#4 (permalink)
alex-andro Freak Poster Join Date: Sep 2003 Location: bulgaria Posts: 256 Member: 40390 Status: Offline Thanks: 0 Thanked 0 Times in 0 Posts	check cable !

01-15-2004, 09:00	#6 (permalink)
tical No Life Poster Join Date: Nov 2003 Location: Americas Age: 33 Posts: 2,101 Member: 43802 Status: Offline Thanks: 3 Thanked 30 Times in 23 Posts	I discovered my problem. be sure to remove foam/sponge from around contacts on cable. It then worked