|
Welcome to the GSM-Forum forums. You are currently viewing our boards as a guest which gives you limited access to view most discussions and access our other features. Only registered members may post questions, contact other members or search our database of over 8 million posts. Registration is fast, simple and absolutely free so please - Click to REGISTER! If you have any problems with the registration process or your account login, please contact contact us . |
|
Register | FAQ | Donate | Forum Rules | Root any Device | ★iPhone Unlock★ | ★ Direct Codes ★ | Direct Unlock Source |
Nokia Hardware & Hardware Repair all what you need for Hardware Repairing for Nokia Phones. Before writing any thread here try to check the Frequently Asked Questions Section. |
| LinkBack | Thread Tools | Display Modes |
08-01-2002, 15:59 | #1 (permalink) |
Freak Poster Join Date: Sep 2001 Location: Europe Age: 48
Posts: 120
Member: 6245 Status: Offline Thanks Meter: 0 | 3210 doesn't show level of signal but works It doesn't show bars of signal's level but works. I changed COBBA but it didn't help I think cause is in ADC, but where is it in 3210 ? Thank you in advance |
08-01-2002, 20:38 | #2 (permalink) |
Freak Poster Join Date: Sep 2001 Location: Europe Age: 48
Posts: 120
Member: 6245 Status: Offline Thanks Meter: 0 | Quatation from Service Manual: – The SUMMA includes: – An AGC amplifier for the receiver – A receiver mixer for the 13 MHz down conversion – PLLs for the UHF and VHF synthesizers – IQ–modulators for the transmitter – A power control circuit for the transmitter The power amplifiers (PAs) are MMIC technology (Monolithic Microwave Integrated Circuit). They include three amplifier stages with input, interstage and output matching. I think cause in that. I'll try to change Summa |
08-03-2002, 00:03 | #3 (permalink) | |
No Life Poster Join Date: Mar 2000 Location: inside NOKIA phone Age: 58
Posts: 1,677
Member: 1060 Status: Offline Thanks Meter: 10 | Re: 3210 doesn't show level of signal but works Roller some time, 3210 have rusty pad at COBBA , try to see some "black pad" in COBBA PCB ! Willy Quote:
| |
08-03-2002, 05:31 | #4 (permalink) |
No Life Poster Join Date: Jul 2002 Location: Bucharest-Romania Age: 51
Posts: 1,160
Member: 14200 Status: Offline Sonork: Sonork id Thanks Meter: 117 | hello roller, 1. verify board circuit from duplexor filter to antenna 2. change the duplexor filter(antena swich) geo Last edited by george gsm; 08-03-2002 at 05:43. |
Bookmarks |
| |
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
U700 - shows full signal, but says "Emergency Calls Only" | Jazz | NSPRO | 11 | 11-20-2009 15:28 |
T429 no signal but work on paktel(zong) | alamgarh | Samsung Hardware Repair | 9 | 05-26-2009 12:44 |
V220 dead_always in flash mode but doesn't show anything... | plruzza | Motorola P2k | 11 | 02-07-2007 19:46 |
3210 with signal but no tx / rx | oel | Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L ) | 7 | 10-27-2004 05:51 |
3210 After charging no power on, but works with other batterie | Squesch | Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L ) | 1 | 05-13-2002 10:58 |
|