Lumia 800 dead before operation, dead after operation

[unlock.mk]

Receved handset in dead condition. Only vibrates.
After boot repair went well without error on the first try, then SP unlock OK too.

But phone after all this is in the same conditiion as i have receved. (Only vibrate)

On PC is recognised like (qualcomm cdma technologies msm )

I am saw THIS, and i just want ask is there a solution ?

Lumia 800 boot write

13:05:37 : ================================================== ====
13:05:37 : ================================================== ====
13:05:37 : eMMC Test Point Connection Module
13:05:37 : ================================================== ====
13:05:37 : ================================================== ====
13:05:37 :
13:05:37 : 1. DO NOT USE THE PHONE"S BATTERY
13:05:37 : 2. Connect the Soldered TP Connections to ATF Box
13:05:37 : 3. Disconnect the USB Cable and Wait until the
13:05:37 : the ATF Software will tell you to Connect the USB.
13:05:37 :
13:05:37 : MMC_TP_SEND_CMD: 0200000000A9FF
13:05:37 : MMC_TP_SEND_CMD: 8202FF010191
13:05:37 : REPLY CMD1: 3F40FF8080FFFF
13:05:37 : MMC_TP_SEND_CMD: 8202FF010191
13:05:37 : REPLY CMD1: 3FC0FF8080FFFF
13:05:37 :
13:05:37 : Interface Reset OK!
13:05:37 : eMMC Supported Voltage Range:
13:05:37 : 3.5-3.6V, 3.4-3.5V, 2.7-2.8V, 2.6-2.7V, 2.5-2.6V
2.4-2.5V, 2.3-2.4V, 2.2-2.3V, 2.1-2.2V, 2.0-2.1V
1.9-2.0V
13:05:37 : MMC_TP_SEND_CMD: 4200000000B2
13:05:37 : REPLY CMD2: 3F90014A48594E4958205C000F23C3AE39FF
13:05:37 :
13:05:37 : CID : 90014A48594E4958205C000F23C3
13:05:37 : MMC_TP_SEND_CMD: C200800000FE
13:05:37 : REPLY CMD3: 0300000500FBFF
13:05:37 : MMC_TP_SEND_CMD: 92008000008F
13:05:37 : REPLY CMD9: 3FD04F01320F5903FFFFFFFFFF8A400001FF
13:05:37 : CSD : D04F01320F5903FFFFFFFFFF8A400001
13:05:37 : MMC_TP_SEND_CMD: E200800000BB
13:05:37 : REPLY CMD7: 070000070075FF
13:05:37 :
13:05:37 : MMC_TP_SEND_CMD: 0A00004000A8
13:05:37 : REPLY CMD16: 10000009000BFF
13:05:37 : MMC_TP_SEND_CMD: 1200000000C3
13:05:37 : REPLY CMD8: 0800000900F1FF
13:05:37 : eMMC Boot Information
13:05:37 : BOOT PARTITION : USER AREA
13:05:37 : PARTITION ACCESS : R/W USER PARTITION
13:05:37 : PERM_BOOT_CFG_PROT: DISABLED
13:05:37 : PWR_BOOT_CFG_PROT : DISABLED
13:05:37 : eMMC FirmW UPDATE : DISABLED
13:05:37 :
13:05:37 : MMC_TP_SEND_CMD: 62C09D8000F4
13:05:37 : REPLY CMD6: 0600000800CBFF
13:05:37 : MMC_TP_SEND_CMD: 1200000000C3
13:05:37 : REPLY CMD8: 0800000900F1FF
13:05:37 : MMC_TP_SEND_CMD: 8A00000000AA
13:05:37 : REPLY CMD17: 110000090067FF
13:05:37 : Lumia 800/800C Detected
13:05:37 :
13:05:37 : eMMC Device Information
13:05:37 : Manufacturer ID: HYNIX
13:05:37 : Device Type : Embedded BGA
13:05:37 : Application ID : 4A
13:05:37 : Product Name : HYNIX
13:05:37 : Product Rev : 5.12
13:05:37 : Product SN : 000F23C3
13:05:37 : Manufactured : January 2011
13:05:37 :
13:05:37 : Card Specific Data
13:05:37 : CSD_STRUCTURE : Extended
13:05:37 : SPEC_VERS : Version 4.1/4.2/4.3
13:05:37 : TAAC : 300 ns
13:05:37 : TRANS_SPEED : 4000000 KHz
13:05:37 : READ_BL_LEN : 512 Bytes
13:05:37 : C_SIZE : HIGH CAPACITY
13:05:37 : WP_GRP_ENABLE : YES
13:05:37 : WRITE_BL_LEN : 512 Bytes
13:05:37 : CONTENT_PROT_APP : NO
13:05:37 : PERM_WRITE_PROTECT: NO
13:05:37 : TMP_WRITE_PROTECT : NO
13:05:37 : MMC_TP_SEND_CMD: B200800000CA
13:05:37 : REPLY CMD13: 0D000009003FFF
13:05:37 :
13:05:37 : Writing MBR...
13:05:37 : MMC_TP_SEND_CMD: 1A00000000F6
13:05:37 : REPLY CMD24: 18000009005DFF
13:05:37 : Write Success!
13:05:37 : Writing DBL...
13:05:37 : MMC_TP_SEND_CMD: 1A00000080BE .....................................

[el-polaco]

that bad, apparently no solution. -
would be good to know to prevent this situation.
The interesting thing would be how to tell if this will happen or not. before breaking the Cellular and unusable. -

P0lac0

[..::Angel::..]

@unlock.mk

How to repair WP7.x boot with ATF
After you repair the boot, phone will ask for OSBL DLOAD drivers
and not QUALCOMM... You will need to flash it once phone is on
OSBL DLOAD.

BR