oppo A3S not detected - GSM-Forum

nagisa_moe · 06-27-2019, 08:36

i got 1pcs cph1803 and 1pcs cph1853 with this emmc h9tq27adftmcur-kum same error like this
Loading eMMC GEN1 Firmware... IO: 2800 mV
Box S/N: 01FF801925CE6B82, ,FW Ver.: 01.63
CMD Pullup Level:2052 mV
CMD Active Level:2392 mV
Box IO Level:2800 mV
CLK Rate:21000 kHz
Bus Width:1bit,SDR
HiPower mode is off!
Can't init device, Reason: CARD Ready Timeout Error
how to solve this problem

Deni's · 07-01-2019, 09:30

Found 3 serial devices
COM6 USB\VID_0325&PID_0032&REV_0100&MI_00 Easy Jtag Control Port (COM6)
COM1 ACPI\VEN_PNP&DEV_0501 Communications Port (COM1)
COM5 USB\VID_05C6&PID_9008&REV_0000 Qualcomm HS-USB QDLoader 9008 (COM5)
Selected pinout: EasyJTAG GEN1 ISP Pinout
Change EasyJTAG Pinout OK
Z3X EasyJtag Software ver. 3.6.1.4
Loading eMMC GEN1 Firmware... IO: 2800 mV
Box S/N: 0F01300C22E581EB, ,FW Ver.: 01.63
CMD Pullup Level:1990 mV
CMD Active Level:2557 mV
Box IO Level:2800 mV
CLK Rate:21000 kHz
Bus Width:1bit,SDR
HiPower mode is ON!
Can't init device, Reason: CMD Timeout Error
Done.

Z3X EasyJtag Software ver. 3.6.1.4
Loading eMMC GEN1 Firmware... IO: 2800 mV
Box S/N: 0F01300C22E581EB, ,FW Ver.: 01.63
CMD Pullup Level:1980 mV
CMD Active Level:2547 mV
Box IO Level:2800 mV
CLK Rate:21000 kHz
Bus Width:1bit,SDR
HiPower mode is ON!
Can't init device, Reason: CMD Timeout Error
Done.

gsm50238301 · 07-01-2019, 09:53

just check cmd donly and use usb to power handset sold only cmd clk d0

Reason gurung · 07-01-2019, 10:15

check cmd do clk. use usb cable dont use battery.

Deni's · 07-01-2019, 10:17

Quote:

Originally Posted by gsm50238301

just check cmd donly and use usb to power handset sold only cmd clk d0

sold wire is good..yes i just sold cmd-clk and do.

Deni's · 07-02-2019, 05:59

and now..device stuck on qualcomm 8009.

Deni's · 07-02-2019, 07:35

any solution a3s stuck on 9008???

rico_deep · 07-02-2019, 08:13

check clk,cmd resistor, maybe damage

.:AMINUS:. · 07-02-2019, 08:39

i have same problem .

d'starter · 07-02-2019, 08:45

on CLK rATE select ---1mhz OI voltage select isp

Deni's · 07-02-2019, 13:51

Quote:

Originally Posted by rico_deep

check clk,cmd resistor, maybe damage

if damage..what should i do..?

layder · 07-02-2019, 16:45

Quote:

Originally Posted by Deni's

if damage..what should i do..?

You need replace it to some.

Deni's · 07-03-2019, 04:46

Quote:

Originally Posted by layder

You need replace it to some.

problem solved after make jumper..

Bhagat20 · 07-03-2019, 04:52

Quote:

Originally Posted by Deni's

problem solved after make jumper..

Please explain in details, where did you make jumper? And also tell if after jumper are you able to connect with easy jtag?

desai123 · 07-03-2019, 06:30

remove register & make jumper i have same problem
help me thanks

06-27-2019, 08:36	#1 (permalink)
nagisa_moe Junior Member Join Date: Feb 2015 Posts: 8 Member: 2353294 Status: Offline Thanks Meter: 4	oppo a3s cant detect i got 1pcs cph1803 and 1pcs cph1853 with this emmc h9tq27adftmcur-kum same error like this Loading eMMC GEN1 Firmware... IO: 2800 mV Box S/N: 01FF801925CE6B82, ,FW Ver.: 01.63 CMD Pullup Level:2052 mV CMD Active Level:2392 mV Box IO Level:2800 mV CLK Rate:21000 kHz Bus Width:1bit,SDR HiPower mode is off! Can't init device, Reason: CARD Ready Timeout Error how to solve this problem

07-01-2019, 09:30	#2 (permalink)
Deni's No Life Poster Join Date: Aug 2012 Location: Bali-Indonesia Posts: 2,908 Member: 1800628 Status: Offline Thanks Meter: 940	oppo A3S not detected Found 3 serial devices COM6 USB\VID_0325&PID_0032&REV_0100&MI_00 Easy Jtag Control Port (COM6) COM1 ACPI\VEN_PNP&DEV_0501 Communications Port (COM1) COM5 USB\VID_05C6&PID_9008&REV_0000 Qualcomm HS-USB QDLoader 9008 (COM5) Selected pinout: EasyJTAG GEN1 ISP Pinout Change EasyJTAG Pinout OK Z3X EasyJtag Software ver. 3.6.1.4 Loading eMMC GEN1 Firmware... IO: 2800 mV Box S/N: 0F01300C22E581EB, ,FW Ver.: 01.63 CMD Pullup Level:1990 mV CMD Active Level:2557 mV Box IO Level:2800 mV CLK Rate:21000 kHz Bus Width:1bit,SDR HiPower mode is ON! Can't init device, Reason: CMD Timeout Error Done. Z3X EasyJtag Software ver. 3.6.1.4 Loading eMMC GEN1 Firmware... IO: 2800 mV Box S/N: 0F01300C22E581EB, ,FW Ver.: 01.63 CMD Pullup Level:1980 mV CMD Active Level:2547 mV Box IO Level:2800 mV CLK Rate:21000 kHz Bus Width:1bit,SDR HiPower mode is ON! Can't init device, Reason: CMD Timeout Error Done.

07-01-2019, 09:53	#3 (permalink)
gsm50238301 Freak Poster Join Date: Nov 2014 Posts: 145 Member: 2288140 Status: Offline Thanks Meter: 46	just check cmd donly and use usb to power handset sold only cmd clk d0

07-01-2019, 10:15	#4 (permalink)
Reason gurung Freak Poster Join Date: Oct 2010 Posts: 334 Member: 1429499 Status: Offline Thanks Meter: 28	check cmd do clk. use usb cable dont use battery.

07-02-2019, 05:59	#6 (permalink)
Deni's No Life Poster Join Date: Aug 2012 Location: Bali-Indonesia Posts: 2,908 Member: 1800628 Status: Offline Thanks Meter: 940	and now..device stuck on qualcomm 8009.

07-02-2019, 07:35	#7 (permalink)
Deni's No Life Poster Join Date: Aug 2012 Location: Bali-Indonesia Posts: 2,908 Member: 1800628 Status: Offline Thanks Meter: 940	any solution a3s stuck on 9008???

07-02-2019, 08:13	#8 (permalink)
rico_deep No Life Poster Join Date: Jul 2005 Location: philippine Posts: 1,113 Member: 159757 Status: Offline Thanks Meter: 461	check clk,cmd resistor, maybe damage

07-02-2019, 08:39	#9 (permalink)
.:AMINUS:. Junior Member Join Date: Jun 2019 Location: in my pc Posts: 5 Member: 2914785 Status: Offline Thanks Meter: 1	i have same problem .

07-02-2019, 08:45	#10 (permalink)
d'starter Crazy Poster Join Date: Jun 2010 Location: cold place Posts: 57 Member: 1316900 Status: Offline Sonork: none Thanks Meter: 30	on CLK rATE select ---1mhz OI voltage select isp

07-03-2019, 06:30	#15 (permalink)
desai123 Junior Member Join Date: Oct 2015 Posts: 23 Member: 2471614 Status: Offline Thanks Meter: 3	remove register & make jumper i have same problem help me thanks