Programming Greencard2 ERRORS - GSM-Forum

hanglider_62 · 04-02-2004, 08:55

Hi,
i tried to write on Green2 Galaxy card Pic 877 - 256EEPROM with SmartMouse/Phoenix programmer configured as Phoenix 3.57Mhz but impossible to do it:
"error address 000h" ???
so perhaps my programmer is not good??

With Dejan simscan2.01 and Cardinal all is ok!..I'm able to read and write any simcard, but with IcProg1.05A and IcProg1.05C nothing to do! Always.."error address 000h" !!
Otherwise where can i found a good but cheap programmer for Sim cloning ....?
Any suggestions?..
Thanx
Hg_62

vrba · 04-02-2004, 09:28

In ICprog select PIC16F877A. Prefer OS Win98.

hanglider_62 · 04-02-2004, 10:00

Thank!
Yesterday initially setted SmartMouse/Phoenix osc.freq. to 6.00MHz, and this can damage the waferchip? Then I tried others setting but always..
"error address 000h" !!!
I hope You are rigth..otherwise I'm afraid, peraphs, my 2 greencard are broken!
Anymode is ok..it works fine with simscan2.01 and Cardinal but not with IcProg1.05A and IcProg1.05C!
P.S. Is ok set programmer as JDM? SmartMouse/Phoenix is not present in IcProg1.05C list!
Thanx again!

hg_62

hanglider_62 · 04-02-2004, 10:08

Sorry at all..I hope not annoying..
My O.S. is Windows98SE, SmartMouse/Phoenix programmer configured as Phoenix 3.57Mhz on COM2. Is necessary some particular setting in IcProg1.05C for it? I tried much different possible setting adviced in HelpFile..

Thanx again...again!

hg_62

jsompis · 04-02-2004, 14:32

Quote:

Originally Posted by hanglider_62

Sorry at all..I hope not annoying..
My O.S. is Windows98SE, SmartMouse/Phoenix programmer configured as Phoenix 3.57Mhz on COM2. Is necessary some particular setting in IcProg1.05C for it? I tried much different possible setting adviced in HelpFile..

Thanx again...again!

hg_62

don't forget to set : Setting-->Smartcard(Phoenix) , coz u much use though pic programming method to programe eeprom on pic.

simemu · 04-02-2004, 17:39

You must first to write the flash file with a TE-20 programmer (JDM device in ICProg).
Then you must to write the external EEPROM file with a Phoenix and to make this, I recommend the new SIM-EMU configurator.

Regards

hanglider_62 · 04-02-2004, 18:58

To simemu:
Thank

A question: my SmartMouse/Phoenix programmer isn't good to write the flash? Is right?! Then I have to buy a TE-20 programmer?
Thank again

hg_62

simemu · 04-02-2004, 19:15

Your SmartMouse/Phoenix programmer is only for writing external EEPROM.
For the flash programming, you must to have a TE-20 programmer.

Regards

Nighty · 04-03-2004, 00:38

@SIMEMU

Dear Daniel, first of all your built-in loader is exellent feature! Thank you so much for everything!

Could you please answer one qwestion?

You use the same "loader-code" for both 8/16/32 KB cards? I mean during configuring the PIC/EEPROM for different cards the code of the loader remains the same?

Thank you!

simemu · 04-03-2004, 15:51

Of course, the loader is the same. Look at my new SIM-EMU Configurator program (EEPROM tabsheet) that detects the EEPROM type and it allows to read/write the EEPROM.

Regards

hanglider_62 · 04-03-2004, 16:26

@SIMEMU

You have written me
"SmartMouse/Phoenix programmer is only for writing external EEPROM.
For the flash programming, you must to have a TE-20 programmer."

Ok! i've to buy this programmer.. I was locking for this programmer but..nothing!
Instead I've found a Multiprogrammer 2001 XL or MAESTRO Card Programmer..are they equivalent/usable instead of TE-20 programmer? Any other suggestion..?
Thanx

Regard

hg_62

simemu · 04-03-2004, 16:56

They are multiprogrammer and works as Phoenix and JDM (TE-20).
They are more expensive that a simple TE-20, but they are fine to your needs.
I don't know which of them is better, ask in this forum for a recommendation.

Regards

Tina_sk9 · 04-08-2004, 14:37

Quote:

Originally Posted by hanglider_62

@SIMEMU

You have written me
"SmartMouse/Phoenix programmer is only for writing external EEPROM.
For the flash programming, you must to have a TE-20 programmer."

Ok! i've to buy this programmer.. I was locking for this programmer but..nothing!
Instead I've found a Multiprogrammer 2001 XL or MAESTRO Card Programmer..are they equivalent/usable instead of TE-20 programmer? Any other suggestion..?
Thanx

Regard

hg_62

Hi,
There is not needed another programmer if you have jdm and phoenix programmer.
At first you need write flash hex with JDM programmer ,and then eeprom hex with phoenix programmer.I have Win Me ,ICprog 1.5C ,Winphoenix, and all works fine.(did you try increase I/O delay timming values?)
Yesterday I got 6 greencards ,4 I have done and two does not responding and says error 000f.All card are from malaysia and are in iso format.
I think that fault sometime becomes during cutting to plug-in format,because some cards have too soft cover, and chip is mechanically destoyed.Maybe...
Tina
sorry my bad english....

aldi1 · 04-08-2004, 15:50

hi can someone tell me where can i buy some cards in internet.

04-02-2004, 08:55	#1 (permalink)
hanglider_62 Junior Member Join Date: Dec 2002 Location: Italy, near Rome Age: 62 Posts: 33 Member: 19340 Status: Offline Thanks Meter: 0	Programming Greencard2 ERRORS Hi, i tried to write on Green2 Galaxy card Pic 877 - 256EEPROM with SmartMouse/Phoenix programmer configured as Phoenix 3.57Mhz but impossible to do it: "error address 000h" ??? so perhaps my programmer is not good?? With Dejan simscan2.01 and Cardinal all is ok!..I'm able to read and write any simcard, but with IcProg1.05A and IcProg1.05C nothing to do! Always.."error address 000h" !! Otherwise where can i found a good but cheap programmer for Sim cloning ....? Any suggestions?.. Thanx Hg_62

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
* Failed to write CMT cert data (3), Programming Status Error *	karwos	Cyclonebox	62	05-23-2013 20:20
Genie all program get error after update firmware [ANSWERED]	tgcommss	Genie Universal	15	05-26-2010 09:53
Error programing Greencard2. Help!	Dobbie	Sim Cloning and Scaning	3	10-01-2004 14:15
Programing Sim Error -help	hcivil	Sim Cloning and Scaning	3	01-15-2003 17:33

04-02-2004, 09:28	#2 (permalink)
vrba Freak Poster Join Date: Mar 2001 Location: srbija Posts: 159 Member: 3538 Status: Offline Thanks Meter: 1	In ICprog select PIC16F877A. Prefer OS Win98.

04-02-2004, 10:00	#3 (permalink)
hanglider_62 Junior Member Join Date: Dec 2002 Location: Italy, near Rome Age: 62 Posts: 33 Member: 19340 Status: Offline Thanks Meter: 0	Thank! Yesterday initially setted SmartMouse/Phoenix osc.freq. to 6.00MHz, and this can damage the waferchip? Then I tried others setting but always.. "error address 000h" !!! I hope You are rigth..otherwise I'm afraid, peraphs, my 2 greencard are broken! Anymode is ok..it works fine with simscan2.01 and Cardinal but not with IcProg1.05A and IcProg1.05C! P.S. Is ok set programmer as JDM? SmartMouse/Phoenix is not present in IcProg1.05C list! Thanx again! hg_62

04-02-2004, 10:08	#4 (permalink)
hanglider_62 Junior Member Join Date: Dec 2002 Location: Italy, near Rome Age: 62 Posts: 33 Member: 19340 Status: Offline Thanks Meter: 0	Sorry at all..I hope not annoying.. My O.S. is Windows98SE, SmartMouse/Phoenix programmer configured as Phoenix 3.57Mhz on COM2. Is necessary some particular setting in IcProg1.05C for it? I tried much different possible setting adviced in HelpFile.. Thanx again...again! hg_62

04-02-2004, 17:39	#6 (permalink)
simemu No Life Poster Join Date: Apr 2002 Location: Spain Age: 62 Posts: 855 Member: 10582 Status: Offline Thanks Meter: 99	You must first to write the flash file with a TE-20 programmer (JDM device in ICProg). Then you must to write the external EEPROM file with a Phoenix and to make this, I recommend the new SIM-EMU configurator. Regards

04-02-2004, 18:58	#7 (permalink)
hanglider_62 Junior Member Join Date: Dec 2002 Location: Italy, near Rome Age: 62 Posts: 33 Member: 19340 Status: Offline Thanks Meter: 0	To simemu: Thank A question: my SmartMouse/Phoenix programmer isn't good to write the flash? Is right?! Then I have to buy a TE-20 programmer? Thank again hg_62

04-02-2004, 19:15	#8 (permalink)
simemu No Life Poster Join Date: Apr 2002 Location: Spain Age: 62 Posts: 855 Member: 10582 Status: Offline Thanks Meter: 99	Your SmartMouse/Phoenix programmer is only for writing external EEPROM. For the flash programming, you must to have a TE-20 programmer. Regards

04-03-2004, 00:38	#9 (permalink)
Nighty Junior Member Join Date: Mar 2003 Posts: 23 Member: 24144 Status: Offline Thanks Meter: 0	@SIMEMU Dear Daniel, first of all your built-in loader is exellent feature! Thank you so much for everything! Could you please answer one qwestion? You use the same "loader-code" for both 8/16/32 KB cards? I mean during configuring the PIC/EEPROM for different cards the code of the loader remains the same? Thank you!

04-03-2004, 15:51	#10 (permalink)
simemu No Life Poster Join Date: Apr 2002 Location: Spain Age: 62 Posts: 855 Member: 10582 Status: Offline Thanks Meter: 99	Of course, the loader is the same. Look at my new SIM-EMU Configurator program (EEPROM tabsheet) that detects the EEPROM type and it allows to read/write the EEPROM. Regards

04-03-2004, 16:26	#11 (permalink)
hanglider_62 Junior Member Join Date: Dec 2002 Location: Italy, near Rome Age: 62 Posts: 33 Member: 19340 Status: Offline Thanks Meter: 0	@SIMEMU You have written me "SmartMouse/Phoenix programmer is only for writing external EEPROM. For the flash programming, you must to have a TE-20 programmer." Ok! i've to buy this programmer.. I was locking for this programmer but..nothing! Instead I've found a Multiprogrammer 2001 XL or MAESTRO Card Programmer..are they equivalent/usable instead of TE-20 programmer? Any other suggestion..? Thanx Regard hg_62

04-03-2004, 16:56	#12 (permalink)
simemu No Life Poster Join Date: Apr 2002 Location: Spain Age: 62 Posts: 855 Member: 10582 Status: Offline Thanks Meter: 99	They are multiprogrammer and works as Phoenix and JDM (TE-20). They are more expensive that a simple TE-20, but they are fine to your needs. I don't know which of them is better, ask in this forum for a recommendation. Regards

04-08-2004, 15:50	#14 (permalink)
aldi1 Junior Member Join Date: Mar 2004 Age: 39 Posts: 5 Member: 60343 Status: Offline Thanks Meter: 0	hi can someone tell me where can i buy some cards in internet.