GSM-Forum - View Single Post - Write Block Failed, Reason: DATA SND CRC Error-I9300

simcityreal · 05-06-2014, 07:06

Try ed last version (EasyJtag_Release_v1.3.2.0).......BUT Same Rsult..

EasyJtag Suite ver.: 1.3.2.0 / wxWidgets 3.1.0-W-U started.
Operating system ver.: Windows 7 (build 7601, Service Pack 1), 64-bit edition.
Successefuly connected to box on COM83
Box S/N: 16Fxxxxxxxxxxx, ,FW Ver.: 01.50
Box Working Mode: JTAG Box.
Box Drivers version: 3.0.0.0, are OK
Z3X Card Serial : Axxxxxxxx , ver: 22
Z3X EasyJtag Software ver. 1.3.2.0
Loading eMMC Addon Firmware... IO: 1850 mV
Box S/N: 16Fxxxxxxxxxxxxxx, ,FW Ver.: 01.50
Warning: CMD Pullup Level (1082 mV) too low , check cables etc.!!!
CMD Active Level:1392 mV
eMMC Device Information
EMMC CID : 15010056545530304DF11C9627B75FD4
EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 05/2012 Rev.0xf1
EMMC NAME: VTU00M , S/N: 479602615
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
Backup saved: VTU00M_ 479602615_20140402_1108.extcsd
Done.
Writing file...E:\Z3X download\i9300\EMMC_ROM2_2Mb_BOOT\EMMC_ROM2_000000 00_00200000.bin
Z3X EasyJtag Software ver. 1.3.2.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1082 mV
CMD Active Level:1392 mV
Writing 000000200000 bytes to 00000000 ...ROM2
Retry writing adress 0x00000000 (Attempt #1)...
Retry Fail !!!
Retry writing adress 0x00000000 (Attempt #2)...
Retry Fail !!!
Retry writing adress 0x00000000 (Attempt #3)...
Retry Fail !!!
Write Block Failed, Reason: DATA SND CRC Error .........

05-06-2014, 07:06	#2 (permalink)
simcityreal Freak Poster Join Date: Jan 2009 Location: india,kerala..in NAJMU Posts: 393 Member: 955971 Status: Offline Sonork: 100.1638835 Thanks Meter: 115	Tryed last version (EasyJtag_Release_v1.3.2.0) Try ed last version (EasyJtag_Release_v1.3.2.0).......BUT Same Rsult.. EasyJtag Suite ver.: 1.3.2.0 / wxWidgets 3.1.0-W-U started. Operating system ver.: Windows 7 (build 7601, Service Pack 1), 64-bit edition. Successefuly connected to box on COM83 Box S/N: 16Fxxxxxxxxxxx, ,FW Ver.: 01.50 Box Working Mode: JTAG Box. Box Drivers version: 3.0.0.0, are OK Z3X Card Serial : Axxxxxxxx , ver: 22 Z3X EasyJtag Software ver. 1.3.2.0 Loading eMMC Addon Firmware... IO: 1850 mV Box S/N: 16Fxxxxxxxxxxxxxx, ,FW Ver.: 01.50 Warning: CMD Pullup Level (1082 mV) too low , check cables etc.!!! CMD Active Level:1392 mV eMMC Device Information EMMC CID : 15010056545530304DF11C9627B75FD4 EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C EMMC Manufacturer ID: 0015 , OEM ID: 0100 EMMC Date: 05/2012 Rev.0xf1 EMMC NAME: VTU00M , S/N: 479602615 EMMC ROM1 (Main User Data) Capacity: 15028 MB EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB Extended CSD rev 1.6 (MMC 4.5) Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1) Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48. Backup saved: VTU00M_ 479602615_20140402_1108.extcsd Done. Writing file...E:\Z3X download\i9300\EMMC_ROM2_2Mb_BOOT\EMMC_ROM2_000000 00_00200000.bin Z3X EasyJtag Software ver. 1.3.2.0 Skip loading eMMC Addon Firmware CMD Pullup Level:1082 mV CMD Active Level:1392 mV Writing 000000200000 bytes to 00000000 ...ROM2 Retry writing adress 0x00000000 (Attempt #1)... Retry Fail !!! Retry writing adress 0x00000000 (Attempt #2)... Retry Fail !!! Retry writing adress 0x00000000 (Attempt #3)... Retry Fail !!! Write Block Failed, Reason: DATA SND CRC Error .........