GSM-Forum - View Single Post

harold6x · 08-15-2014, 07:24

help with n7100 dead i repaier boot but when i write dump file iget this erorr
Z3X EasyJtag Software ver. 1.6.1.1
Loading eMMC Addon Firmware... IO: 2850 mV
Box S/N: ,FW Ver.: 01.50
Warning: CMD Pullup Level (825 mV) too low , check cables etc.!!!
CMD Active Level:2248 mV
eMMC Device Information
EMMC CID : 15010056545530304DF1C01A144B7F64
EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 07/2012 Rev.0xf1
EMMC NAME: VTU00M , S/N: 3222934603
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
Backup saved: VTU00M_3222934603_20140705_0921.extcsd
Done.
Running:Change BOOT CONFIG...

Z3X EasyJtag Software ver. 1.6.1.1
Skip loading eMMC Addon Firmware
CMD Pullup Level:825 mV
CMD Active Level:2248 mV
Writing eMMC Register...
Written: REG : 179 VAL :48
Done.
Running:Change BOOT WIDTH...

Z3X EasyJtag Software ver. 1.6.1.1
Skip loading eMMC Addon Firmware
CMD Pullup Level:825 mV
CMD Active Level:2248 mV
Writing eMMC Register...
Written: REG : 177 VAL :1
Done.
log write dump
Z3X EasyJtag Software ver. 1.6.1.1
Skip loading eMMC Addon Firmware
CMD Pullup Level:825 mV
CMD Active Level:2248 mV
Writing eMMC Register...
Written: REG : 179 VAL :48
Done.
Running:Change BOOT WIDTH...

Z3X EasyJtag Software ver. 1.6.1.1
Skip loading eMMC Addon Firmware
CMD Pullup Level:825 mV
CMD Active Level:2248 mV
Writing eMMC Register...
Written: REG : 177 VAL :1
Done.

Z3X EasyJtag Software ver. 1.6.1.1
Skip loading eMMC Addon Firmware
CMD Pullup Level:825 mV
CMD Active Level:2248 mV
Input file : D:\s6312\n7100\N7100_Rom1_Alive_Dump_BN.bin
Writing 000020000000 bytes to 00000000 ...ROM2 (BOOT1 ROM)
Write Length has been corrected to 0x000000200000 bytes...
Retry writing adress 0x00000000 (Attempt #1)...
Retry Fail !!!
Retry writing adress 0x00000000 (Attempt #2)...
Retry Fail !!!
Retry writing adress 0x00000000 (Attempt #3)...
Retry Fail !!!
Write Block Failed, Reason: DATA SND CRC Error

08-15-2014, 07:24	#1 (permalink)
harold6x No Life Poster Join Date: Apr 2006 Location: syria Age: 46 Posts: 909 Member: 257716 Status: Offline Sonork: 1650684 Thanks Meter: 57	help with n7100 dead help with n7100 dead i repaier boot but when i write dump file iget this erorr Z3X EasyJtag Software ver. 1.6.1.1 Loading eMMC Addon Firmware... IO: 2850 mV Box S/N: ,FW Ver.: 01.50 Warning: CMD Pullup Level (825 mV) too low , check cables etc.!!! CMD Active Level:2248 mV eMMC Device Information EMMC CID : 15010056545530304DF1C01A144B7F64 EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C EMMC Manufacturer ID: 0015 , OEM ID: 0100 EMMC Date: 07/2012 Rev.0xf1 EMMC NAME: VTU00M , S/N: 3222934603 EMMC ROM1 (Main User Data) Capacity: 15028 MB EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB Extended CSD rev 1.6 (MMC 4.5) Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1) Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48. Backup saved: VTU00M_3222934603_20140705_0921.extcsd Done. Running:Change BOOT CONFIG... Z3X EasyJtag Software ver. 1.6.1.1 Skip loading eMMC Addon Firmware CMD Pullup Level:825 mV CMD Active Level:2248 mV Writing eMMC Register... Written: REG : 179 VAL :48 Done. Running:Change BOOT WIDTH... Z3X EasyJtag Software ver. 1.6.1.1 Skip loading eMMC Addon Firmware CMD Pullup Level:825 mV CMD Active Level:2248 mV Writing eMMC Register... Written: REG : 177 VAL :1 Done. log write dump Z3X EasyJtag Software ver. 1.6.1.1 Skip loading eMMC Addon Firmware CMD Pullup Level:825 mV CMD Active Level:2248 mV Writing eMMC Register... Written: REG : 179 VAL :48 Done. Running:Change BOOT WIDTH... Z3X EasyJtag Software ver. 1.6.1.1 Skip loading eMMC Addon Firmware CMD Pullup Level:825 mV CMD Active Level:2248 mV Writing eMMC Register... Written: REG : 177 VAL :1 Done. Z3X EasyJtag Software ver. 1.6.1.1 Skip loading eMMC Addon Firmware CMD Pullup Level:825 mV CMD Active Level:2248 mV Input file : D:\s6312\n7100\N7100_Rom1_Alive_Dump_BN.bin Writing 000020000000 bytes to 00000000 ...ROM2 (BOOT1 ROM) Write Length has been corrected to 0x000000200000 bytes... Retry writing adress 0x00000000 (Attempt #1)... Retry Fail !!! Retry writing adress 0x00000000 (Attempt #2)... Retry Fail !!! Retry writing adress 0x00000000 (Attempt #3)... Retry Fail !!! Write Block Failed, Reason: DATA SND CRC Error