GSM-Forum - View Single Post - lumia 610 unlocking Timeout during operation

bakibaruwa · 02-03-2015, 20:17

Default language ID 0x0409
JTAG Interface Connected, S/N 0xA414EAC9
Resetting and Exploring JTAG chain...No Devices found in Chain!
Loading AFP (Please Wait)...OK
AFP revision 4, compiled 7/8/2014 10:52:00 PM

================================================== ========
Phone Type : Lumia 610 RM-835 - Supported
: Lumia 610 RM-849 - Supported
: Lumia 610C RM-836 - Supported
: Lumia 510 RM-889 - Supported
: Lumia 510 RM-898 - Supported
: Lumia 505 RM-923 - Supported
Unlock Type : Read PIN and PUK Unlock Codes
Other Notes : Power On Phone before Reading Codes
================================================== ========
1. Make sure JTAG Connection is 100% OK
2. DO NOT Connect a USB Cable to the phone
3. Connect RJ-45 JTAG Cable to ATF Box
4. Connect Phone BATTERY and POWER ON the Phone
5. Wait until WP7 OS is FULLY LOADED showing Main Menu
6. Check that Phone IMEI is valid via *#06#
7. If IMEI is valid, Click READ CODES button then wait...
----------------------------------------------------------

Initializing Connection
Timeout During Operation!

Initializing Connection
Connected 1 device(s)!
Halting Core...
Halted Device 0x106210E1
Searching for PIN/PUK Unlock Codes...
Please wait for a while...
Codes Found!

=========================
PIN LEVEL 1: 89713198 - LOCKED
PUK LEVEL 1: 06273338 - LOCKED
PIN LEVEL 2: 73956391
PUK LEVEL 2: 73503104
PIN LEVEL 3: 41153768
PUK LEVEL 3: 67471741
PIN LEVEL 4: 48512886
PUK LEVEL 4: 52313779
PIN LEVEL 5: 76418303
PUK LEVEL 5: 27610594
=========================

Reading Unlock Codes Done!
================================================== ==========================
1. Remove JTAG Connection and Assemble Phone
2. Insert SIM Card from different Provider into the Phone
3. Power ON the Phone
4. Enter 8-digit PIN Code or 8-digit PUK Code when Phone Requires it
5. After Code is accepted, wait 30 seconds until Operator Signal Appears

Write Down 8-digit PIN CODE on a piece of paper and attach
it to the phone under the battery. This will allow the owner
of the phone to unlock this phone again if he will flash the
phone firmware in the future.
================================================== ==========================
All Done!

02-03-2015, 20:17	#2 (permalink)
bakibaruwa Freak Poster Join Date: Jun 2009 Posts: 174 Member: 1049259 Status: Offline Thanks Meter: 14	Default language ID 0x0409 JTAG Interface Connected, S/N 0xA414EAC9 Resetting and Exploring JTAG chain...No Devices found in Chain! Loading AFP (Please Wait)...OK AFP revision 4, compiled 7/8/2014 10:52:00 PM ================================================== ======== Phone Type : Lumia 610 RM-835 - Supported : Lumia 610 RM-849 - Supported : Lumia 610C RM-836 - Supported : Lumia 510 RM-889 - Supported : Lumia 510 RM-898 - Supported : Lumia 505 RM-923 - Supported Unlock Type : Read PIN and PUK Unlock Codes Other Notes : Power On Phone before Reading Codes ================================================== ======== 1. Make sure JTAG Connection is 100% OK 2. DO NOT Connect a USB Cable to the phone 3. Connect RJ-45 JTAG Cable to ATF Box 4. Connect Phone BATTERY and POWER ON the Phone 5. Wait until WP7 OS is FULLY LOADED showing Main Menu 6. Check that Phone IMEI is valid via *#06# 7. If IMEI is valid, Click READ CODES button then wait... ---------------------------------------------------------- Initializing Connection Timeout During Operation! Initializing Connection Connected 1 device(s)! Halting Core... Halted Device 0x106210E1 Searching for PIN/PUK Unlock Codes... Please wait for a while... Codes Found! ========================= PIN LEVEL 1: 89713198 - LOCKED PUK LEVEL 1: 06273338 - LOCKED PIN LEVEL 2: 73956391 PUK LEVEL 2: 73503104 PIN LEVEL 3: 41153768 PUK LEVEL 3: 67471741 PIN LEVEL 4: 48512886 PUK LEVEL 4: 52313779 PIN LEVEL 5: 76418303 PUK LEVEL 5: 27610594 ========================= Reading Unlock Codes Done! ================================================== ========================== 1. Remove JTAG Connection and Assemble Phone 2. Insert SIM Card from different Provider into the Phone 3. Power ON the Phone 4. Enter 8-digit PIN Code or 8-digit PUK Code when Phone Requires it 5. After Code is accepted, wait 30 seconds until Operator Signal Appears Write Down 8-digit PIN CODE on a piece of paper and attach it to the phone under the battery. This will allow the owner of the phone to unlock this phone again if he will flash the phone firmware in the future. ================================================== ========================== All Done!