Hello. Have some problems with p5100 emmc KLMAG2GE4A-A002. Here is log:
Code:
======================================================
======================================================
eMMC Test Point Connection Module
======================================================
======================================================
1. DO NOT USE THE PHONE"S BATTERY
2. Connect the Soldered TP Connections to ATF Box
3. Disconnect the USB Cable and Wait until the
the ATF Software will tell you to Connect the USB.
Interface Reset OK!
eMMC Access Type: SECTOR MODE
eMMC Supported Voltage Range:
3.5-3.6V, 3.4-3.5V, 3.3-3.4V, 3.2-3.3V, 3.1-3.2V
3.0-3.1V, 2.9-3.0V, 2.8-2.9V, 2.7-2.8V, 1.9-2.0V
CID : 1501003030303030305620110726589D
CSD : 902701320F5903FFF6DBFFEF8A404023
eMMC Boot Information
Revision 1.0 (for MMC v4.0)
BOOT PARTITION : NOT BOOT ENABLED
PARTITION ACCESS : R/W USER PARTITION
PERM_BOOT_CFG_PROT : DISABLED
PWR_BOOT_CFG_PROT : DISABLED
BOOT MODE : x1 SINGLE DATA RATE + LOW SPEED
RESET BUS WIDTH : ENABLED
eMMC FirmW UPDATE : DISABLED
EMMC CACHE SIZE : 67108864 KB
SUPER PAGE SIZE : 0 KB
HC ERASE GROUP SIZE: 0 KB
USER AREA SIZE : 0 BYTES
BOOT PARTITION SIZE: 0 KB
RPMB PARTITION SIZE: 0 KB
eMMC Device Information
Manufacturer ID: SAMSUNG
Device Type : Embedded BGA
Application ID : 00
Product Name : 000000
Product Rev : 5.6
Product SN : 20110726
Manufactured : January 2005
Card Specific Data
CSD_STRUCTURE : Version 1.2
SPEC_VERS : Version 4.1/4.2/4.3
TAAC : 13 ns
TRAN_SPEED : 4000000 KHz
READ_BL_LEN : 512 Bytes
C_SIZE : HIGH CAPACITY
WP_GRP_ENABLE : YES
WRITE_BL_LEN : 512 Bytes
CONTENT_PROT_APP : NO
PERM_WRITE_PROTECT: NO
TMP_WRITE_PROTECT : NO
Extended CSD Saved:
1501003030303030305620110726589D.ext_csd
Backup Directory:
H:\atf\AdvanceBox Turbo Flasher\eMMC\EXT_CSD\
Task Selected: Samsung eMMC Firmware Update
======================================================
--> This will ERASE USER AREA, BOOT1, BOOT2, and RPMB
--> This will RESET EXT_CSD Programming Such as BOOT
Options, Bus Characteristics and Partition Sizes..
======================================================
Please Manually Select the Correct
Part Number of your eMMC Device.
======================================================
If you select a WRONG PART NUMBER, then
YOU WILL PROBABLY KILL THE EMMC !!!
======================================================
======================================================
Loading ATF eMMC Firmware File... (Please Wait)
======================================================
File Author: ATF Team @ X-Shadow
Date Created: 16/04/2015 (dd/mm/yyyy)
Description: Samsung eMMC Firmware
eMMC Part Number: KLMAG2GE4A-A001
eMMC Product Name: MAG2GA
eMMC Product Rev: 0.6
Preparing eMMC for Firmware Update...
Sending eMMC Firmware Blocks...
All Blocks Sent!
NAND Write Delay: 1 Second (Please Wait)
Verifying eMMC Firmware...
eMMC Firmware Verify OK!
Applying eMMC Firmware Update...
Waiting for Device Re-Initialization...
Firmware Write Protect Delay: 1 Second (Please Wait)
Checking eMMC Firmware Update Status...
ERROR: eMMC Firmware Programming Failed 0x02
Total Elapsed Time 00:01:00 Emmc is no detected until I apply the testpoint. Afterwards firmware loads ok and then I've got error eMMC Firmware Programming Failed 0x02. I've used the firmware KLMAG2GE4A-A001.emmc_fw.
Any Idea?
Thanks in advance