GSM-Forum - View Single Post - Post here succesfull JTAG and eMMC operations with Easy-Jtag:

waiaw · 07-20-2015, 22:33

CMD Pullup Level:2660 mV
CMD Active Level:2743 mV
eMMC Device Information
EMMC CID : 1501003030584D56300001490116BF36
EMMC CSD : D02701320F5903FFF6DBFFEF8E40400C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 11/2012 Rev.0x0
EMMC NAME: 00XMV0 , S/N: 21561622
EMMC NAME (HEX): 3030584D563000
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 512 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.7 (MMC Unknown)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
Backup saved: 00XMV0_ 21561622_20150602_0430.extcsd
Done.

Running:SAMSUNG: eMMC firmware update...
EMMC NAME: 00XMV0
Confirmed eMMC Part Number: KMV3W000LM-B310
Z3X EasyJtag Software ver. 2.0.3.0
Loading eMMC Addon Firmware... IO: 2800 mV
Box S/N: 0DFFF01B28F9FA7F, ,FW Ver.: 01.52
CMD Pullup Level:2670 mV
CMD Active Level:2722 mV
Setup firmware update mode, wait 2..30 sec...
Success!
Sending eMMC firmware...
Success!
Flashing eMMC firmware...
Success!
Repairing eMMC CID...
Now Reconnect all eMMC Lines [POWER, CMD, CLK, DAT0]!
Do it until progress bar is moving (20 sec timeout)!
Can't init device, Reason: OCR Ready Timeout Error [Check VCC or eMMC DEAD]
Done.

can we modify hw box with a little touch from upgrade in next future to make the power lines to be dynamic??

07-20-2015, 22:33	#428 (permalink)
waiaw Insane Poster Join Date: Aug 2006 Location: under sky Posts: 87 Member: 324879 Status: Offline Thanks Meter: 89	CMD Pullup Level:2660 mV CMD Active Level:2743 mV eMMC Device Information EMMC CID : 1501003030584D56300001490116BF36 EMMC CSD : D02701320F5903FFF6DBFFEF8E40400C EMMC Manufacturer ID: 0015 , OEM ID: 0100 EMMC Date: 11/2012 Rev.0x0 EMMC NAME: 00XMV0 , S/N: 21561622 EMMC NAME (HEX): 3030584D563000 EMMC ROM1 (Main User Data) Capacity: 15028 MB EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB EMMC RPMB (Replay Protected Memory Block) Capacity: 512 kB EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD rev 1.7 (MMC Unknown) Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured. Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00. Backup saved: 00XMV0_ 21561622_20150602_0430.extcsd Done. Running:SAMSUNG: eMMC firmware update... EMMC NAME: 00XMV0 Confirmed eMMC Part Number: KMV3W000LM-B310 Z3X EasyJtag Software ver. 2.0.3.0 Loading eMMC Addon Firmware... IO: 2800 mV Box S/N: 0DFFF01B28F9FA7F, ,FW Ver.: 01.52 CMD Pullup Level:2670 mV CMD Active Level:2722 mV Setup firmware update mode, wait 2..30 sec... Success! Sending eMMC firmware... Success! Flashing eMMC firmware... Success! Repairing eMMC CID... Now Reconnect all eMMC Lines [POWER, CMD, CLK, DAT0]! Do it until progress bar is moving (20 sec timeout)! Can't init device, Reason: OCR Ready Timeout Error [Check VCC or eMMC DEAD] Done. can we modify hw box with a little touch from upgrade in next future to make the power lines to be dynamic??