GSM-Forum - View Single Post - Successful test report by dereje staring U.M.T. [SUCCESS REPORTS]

dereje · 04-21-2018, 18:34

world first only umt QcFire v2.1 can do it
ZTE Grand X3 Z959 counter 0 blocked reset done

after long time waiting thanks to umt team specially U.M.T for suport it is done

Operation : Partial Reset EFS
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM130)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.1.2
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1009600 [8909] 00000400
OPK_DATA : D64F31F1F574B2C3A0A679CA104A03C0F20B4833F5E2F96A2B 56AA09B374C8A6
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Firehose Loader...Done
Sending Loader [8909_044.ufl]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8909, eMMC, 16 GB
LU Count : 1 [0x01D1F000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : ZTE Z959 [msm8909]
Software : Z959V1.5.16, 20170313.101044 [Mon Mar 13 10:12:10 CST 2017]
Android Ver. : 5.1.1
Patch Level : 2017-03-01
Saving EFS Backup.......OK
EFS Backup : EFS_ZTE_Z959_Z959V1.5.16_2017-03-01_180421_101418.ueb
Reset EFS (Partial).....Done
Operation Finished.

Operation : Backup QCN
Searching for Device in FTM Mode...Found
Port : ZTE Handset Diagnostic Interface (COM57)
Hardware ID : usb\vid_19d2&pid_0500&rev_0310&mi_00
Compile : Mar 13 2017 09:40:34
Release : Sep 03 2015 20:00:00
Hw. Ver. : 8909.gen
Software : P890A57V1.0.0B16
IMEI : 868504022531620 / 000000000000000
Reading QCN Data...Done
Saved As : C:\UMTool\QcFire\QCN_Backup\8909.gen_P890A57V1.0.0 B16_868504022531620_180421_101133.qcn
Operation Finished.

Operation : Backup EFS
Checking for existing devices...Found
Port : Qualcomm HS-USB QDLoader 9008 (COM130)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.1.2
Opening Port...OK
Init Handshake Sequence...OK
Hardware ID : E1009600 [8909] 00000400
OPK_DATA : D64F31F1F574B2C3A0A679CA104A03C0F20B4833F5E2F96A2B 56AA09B374C8A6
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Firehose Loader...Done
Sending Loader [8909_044.ufl]...Done
Executing Loader...OK
Detecting Chip Type...OK
Hardware : 8909, eMMC, 16 GB
LU Count : 1 [0x01D1F000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : ZTE Z959 [msm8909]
Software : Z959V1.5.16, 20170313.101044 [Mon Mar 13 10:12:10 CST 2017]
Android Ver. : 5.1.1
Patch Level : 2017-03-01
Saving EFS Backup.......OK
EFS Backup : EFS_ZTE_Z959_Z959V1.5.16_2017-03-01_180421_100933.ueb
Operation Finished.

04-21-2018, 18:34	#72 (permalink)
dereje No Life Poster Join Date: Feb 2007 Location: Ethiopia Posts: 1,518 Member: 449991 Status: Offline Thanks Meter: 933	ZTE Grand X3 Z959 counter 0 blocked reset done world first only umt QcFire v2.1 can do it ZTE Grand X3 Z959 counter 0 blocked reset done after long time waiting thanks to umt team specially U.M.T for suport it is done Operation : Partial Reset EFS Checking for existing devices...Found Port : Qualcomm HS-USB QDLoader 9008 (COM130) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.1.2 Opening Port...OK Init Handshake Sequence...OK Hardware ID : E1009600 [8909] 00000400 OPK_DATA : D64F31F1F574B2C3A0A679CA104A03C0F20B4833F5E2F96A2B 56AA09B374C8A6 Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Firehose Loader...Done Sending Loader [8909_044.ufl]...Done Executing Loader...OK Detecting Chip Type...OK Hardware : 8909, eMMC, 16 GB LU Count : 1 [0x01D1F000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table...OK Reading Device Information...OK Device : ZTE Z959 [msm8909] Software : Z959V1.5.16, 20170313.101044 [Mon Mar 13 10:12:10 CST 2017] Android Ver. : 5.1.1 Patch Level : 2017-03-01 Saving EFS Backup.......OK EFS Backup : EFS_ZTE_Z959_Z959V1.5.16_2017-03-01_180421_101418.ueb Reset EFS (Partial).....Done Operation Finished. Operation : Backup QCN Searching for Device in FTM Mode...Found Port : ZTE Handset Diagnostic Interface (COM57) Hardware ID : usb\vid_19d2&pid_0500&rev_0310&mi_00 Compile : Mar 13 2017 09:40:34 Release : Sep 03 2015 20:00:00 Hw. Ver. : 8909.gen Software : P890A57V1.0.0B16 IMEI : 868504022531620 / 000000000000000 Reading QCN Data...Done Saved As : C:\UMTool\QcFire\QCN_Backup\8909.gen_P890A57V1.0.0 B16_868504022531620_180421_101133.qcn Operation Finished. Operation : Backup EFS Checking for existing devices...Found Port : Qualcomm HS-USB QDLoader 9008 (COM130) Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.1.2 Opening Port...OK Init Handshake Sequence...OK Hardware ID : E1009600 [8909] 00000400 OPK_DATA : D64F31F1F574B2C3A0A679CA104A03C0F20B4833F5E2F96A2B 56AA09B374C8A6 Initializing Protocol...OK Using Auto Loader Selection [1] Preparing Firehose Loader...Done Sending Loader [8909_044.ufl]...Done Executing Loader...OK Detecting Chip Type...OK Hardware : 8909, eMMC, 16 GB LU Count : 1 [0x01D1F000] WARNING! High Speed Driver is not installed. Please install driver from QcFire\Drivers folder using Device Manager. Payload Info : In: 65536 [4096], Out: 1048576, Sector Size: 512 Reading Partition Table...OK Reading Device Information...OK Device : ZTE Z959 [msm8909] Software : Z959V1.5.16, 20170313.101044 [Mon Mar 13 10:12:10 CST 2017] Android Ver. : 5.1.1 Patch Level : 2017-03-01 Saving EFS Backup.......OK EFS Backup : EFS_ZTE_Z959_Z959V1.5.16_2017-03-01_180421_100933.ueb Operation Finished.