[gsaara]

HiPower mode is ON
Setting frequence to 21 Mhz
CMD Pullup Level: 1897 mV
CMD Active Level: 2103 mV
EMMC Device Information :
EMMC CID: 90014A4834473262110124C6DE94424A
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DA
EMMC Manufacture : SKHYNIX , EMMC NAME: H4G2b , HEX: 483447326200 , S/N: 24C6DE94 , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 4/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G2b_24C6DE94_20190501_200116.extcsd
EMMC Init completed.

Opening file: J13G.pit

Pit: J13G.pit
Entry count: 29

The size of the last section has been updated

AP_J100HXXU0AOF2_CL620457_QB5194506_REV01_user_low _ship.tar.md5
The list of files in the firmware:
boot.img
recovery.img
system.img

BL_J100HXXU0AOF2_CL620457_QB5194506_REV01_user_low _ship.tar.md5
The list of files in the firmware:
spl.img
sboot.bin
sboot2.bin
param.lfs

CP_J100HXXU0AOF2_CL620457_QB5194506_REV01_user_low _ship.tar.md5
The list of files in the firmware:
sprdcp.img
sprddsp.img
nvitem.bin

CSC_OJV_J100HOJV0AOF2_CL444269_QB5215362_REV01_use r_low_ship.tar.md5
The list of files in the firmware:
j13g.pit
cache.img
hidden.img

HiPower mode is ON
Setting frequence to 21 Mhz
CMD Pullup Level: 1876 mV
CMD Active Level: 2103 mV
EMMC Device Information :
EMMC CID: 90014A4834473262110124C6DE94424A
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DA
EMMC Manufacture : SKHYNIX , EMMC NAME: H4G2b , HEX: 483447326200 , S/N: 24C6DE94 , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 4/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G2b_24C6DE94_20190501_200126.extcsd
EMMC Init completed.

Operation: Write by vendor (Samsung)

Creating GPT-partitioninig
Writing PrimaryGPT at address: 000000000000
Error writing at address: 000000000000 , error: -1 , CMD Timeout Error ... Retry #1
Error writing at address: 000000000000 , error: 34 , 34 Unknown error ... Retry #2
Error writing at address: 000000000000 , error: -1 , CMD Timeout Error ... Retry #3
Too many errors. Writing has been stopped