| No Life Poster
Join Date: Oct 2010 Location: Abidjan Age: 38
Posts: 2,478
Member: 1418143
Status: Offline Thanks Meter: 353 | till getting error , Quote:
Setting frequence to 14 MHz
CMD Pullup Level: 247 mV
CMD Active Level: 2547 mV
EMMC Device Information :
EMMC CID: 150100514536334D42035050063755B2
EMMC CSD: D02701320F5903FFF6DBFFEF8E40400C
EMMC Manufacture : SAMSUNG , EMMC NAME: QE63MB , HEX: 514536334D42 , S/N: 50500637 , rev. 0x03
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 5/2018
EMMC ROM 1 (Main User Data) Capacity: 14910 MB (0003A3E00000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 22908 , Response: Not Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x38 , Boot from: ROM1 (Main User Area)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: QE63MB_50500637_20191124_223519.extcsd
EMMC Init completed.
Scanning soft partitions
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #1
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #2
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #3
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #4
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #5
Too many errors. Reading has been stopped
| can't use universal format Quote:
Setting frequence to 14 MHz
CMD Pullup Level: 2010 mV
CMD Active Level: 2536 mV
EMMC Device Information :
EMMC CID: 150100514536334D42035050063755B2
EMMC CSD: D02701320F5903FFF6DBFFEF8E40400C
EMMC Manufacture : SAMSUNG , EMMC NAME: QE63MB , HEX: 514536334D42 , S/N: 50500637 , rev. 0x03
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 5/2018
EMMC ROM 1 (Main User Data) Capacity: 14910 MB (0003A3E00000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 22908 , Response: Not Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x38 , Boot from: ROM1 (Main User Area)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: QE63MB_50500637_20191124_223736.extcsd
EMMC Init completed.
Operation: Universal Factory Format
Please, wait ...
Error: 21 Verification error
| cn't read too
Operation: Reading from eMMC... Quote:
Reading from: ROM2 , start: 0x000000000000 , size: 0x000000400000
Output file: C:\Users\Amin\Desktop\OPPO MODEM\read\EMMC_QE63MB_ROM2_000000000000_000000400 000.bin
eMMC switching to ROM2
Reading partition...
Error reading at address: 000000018000 , error: -4, DATA RCV CRC Error ... Retry #1
Error reading at address: 000000018000 , error: -4, DATA RCV CRC Error ... Retry #2
Error reading at address: 000000020000 , error: -206, PORT Read Error ... Retry #1
Error reading at address: 000000020000 , error: -1, CMD Timeout Error ... Retry #2
Error reading at address: 000000020000 , error: -1, CMD Timeout Error ... Retry #3
Too many errors. Reading has been stopped
Try the "Skip unreadable blocks" option
|
Last edited by layder; 11-25-2019 at 07:58.
Reason: merge posts
|