GSM-Forum - View Single Post - Oppo A3s [CPH1803][EDL MODE][DEAD RECOVERED][DONE] by Easy JTAG_H.R Palash

GSMSHOP1 · 06-10-2020, 17:47

Hello Mr

any help for slove this problm im step by step if you possible

THANKS MAN

HiPower mode is ON
Setting frequence to 14 MHz
CMD Pullup Level: 2010 mV
CMD Active Level: 2619 mV
EMMC Device Information :
EMMC CID: 90014A484147346132A5C3375C748594
EMMC CSD: D02701328F5903FFFFFFFFE78A400016
EMMC Manufacture : SKHYNIX , EMMC NAME: HAG4a2 , HEX: 484147346132 , S/N: C3375C74 , rev. 0xA5
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 8/2018
EMMC ROM 1 (Main User Data) Capacity: 15028 MB (0003AB400000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 1237 , Response: Not Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x38 , Boot from: ROM1 (Main User Area)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: HAG4a2_C3375C74_20200610_163554.extcsd
EMMC Init completed.

Get firmware version
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #1
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #2
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #3
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #4
Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #5
Too many errors. Reading has been stopped

.................................................. .................................................. ........................
ERASER EMMC

HiPower mode is ON
Setting frequence to 14 MHz
CMD Pullup Level: 2000 mV
CMD Active Level: 2619 mV
EMMC Device Information :
EMMC CID: 90014A484147346132A5C3375C748594
EMMC CSD: D02701328F5903FFFFFFFFE78A400016
EMMC Manufacture : SKHYNIX , EMMC NAME: HAG4a2 , HEX: 484147346132 , S/N: C3375C74 , rev. 0xA5
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 8/2018
EMMC ROM 1 (Main User Data) Capacity: 15028 MB (0003AB400000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 1237 , Response: Not Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x38 , Boot from: ROM1 (Main User Area)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: HAG4a2_C3375C74_20200610_165209.extcsd
EMMC Init completed.

Operation: Erasing eMMC...

Erasing for: ROM1 , start: 0x000000000000 , size: 0x000000020000
eMMC switching to ROM1
Erasing partition...
Error erasing at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #1
Error erasing at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #2
Error erasing at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #3
Too many errors. Erasing has been stopped

06-10-2020, 17:47	#15 (permalink)
GSMSHOP1 Banned Join Date: Jan 2007 Location: morroco rabat massira n67 sect Age: 51 Posts: 430 Member: 443140 Status: Offline Thanks Meter: 45	Hello Mr any help for slove this problm im step by step if you possible THANKS MAN HiPower mode is ON Setting frequence to 14 MHz CMD Pullup Level: 2010 mV CMD Active Level: 2619 mV EMMC Device Information : EMMC CID: 90014A484147346132A5C3375C748594 EMMC CSD: D02701328F5903FFFFFFFFE78A400016 EMMC Manufacture : SKHYNIX , EMMC NAME: HAG4a2 , HEX: 484147346132 , S/N: C3375C74 , rev. 0xA5 EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 8/2018 EMMC ROM 1 (Main User Data) Capacity: 15028 MB (0003AB400000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 1237 , Response: Not Clean EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD Information : Extended CSD rev: 1.8 (MMC 5.1) Boot configuration [PARTITION_CONFIG]: 0x38 , Boot from: ROM1 (Main User Area) Boot Bus Config: 0x00 , width 1bit H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled Supported partition features [PARTITIONING_SUPPORT]: 0x07 Device supports partitioning features Device can have enhanced technological features in partitions and user data area Device can have extended partitions attribute Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00 Backup saved: HAG4a2_C3375C74_20200610_163554.extcsd EMMC Init completed. Get firmware version Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #1 Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #2 Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #3 Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #4 Error reading at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #5 Too many errors. Reading has been stopped .................................................. .................................................. ........................ ERASER EMMC HiPower mode is ON Setting frequence to 14 MHz CMD Pullup Level: 2000 mV CMD Active Level: 2619 mV EMMC Device Information : EMMC CID: 90014A484147346132A5C3375C748594 EMMC CSD: D02701328F5903FFFFFFFFE78A400016 EMMC Manufacture : SKHYNIX , EMMC NAME: HAG4a2 , HEX: 484147346132 , S/N: C3375C74 , rev. 0xA5 EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 8/2018 EMMC ROM 1 (Main User Data) Capacity: 15028 MB (0003AB400000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000) EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000) Counter: 1237 , Response: Not Clean EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD Information : Extended CSD rev: 1.8 (MMC 5.1) Boot configuration [PARTITION_CONFIG]: 0x38 , Boot from: ROM1 (Main User Area) Boot Bus Config: 0x00 , width 1bit H/W Reset Function [RST_N_FUNCTION]: 0x01, RST_n signal is permanently enabled Supported partition features [PARTITIONING_SUPPORT]: 0x07 Device supports partitioning features Device can have enhanced technological features in partitions and user data area Device can have extended partitions attribute Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00 Backup saved: HAG4a2_C3375C74_20200610_165209.extcsd EMMC Init completed. Operation: Erasing eMMC... Erasing for: ROM1 , start: 0x000000000000 , size: 0x000000020000 eMMC switching to ROM1 Erasing partition... Error erasing at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #1 Error erasing at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #2 Error erasing at address: 000000000000 , error: -1, CMD Timeout Error ... Retry #3 Too many errors. Erasing has been stopped Last edited by GSMSHOP1; 06-10-2020 at 17:53.