| mi note 8 pro hw report test done
Infinity-Box [ Chinese Miracle ] MediaTek Service Module [ MTK ] v2.17
Load IDBase v729152 Ok!
Operation : HW Report [ v2.17 ]
HWreport : Mode : UFS
1. Make sure device is powered off. Power off, if need. Wait 20 seconds after
2. Insert USB cable in phone
Waiting for device connection ...
PTFN : MediaTek USB Port (COM5)
MODE : BOOTROM
PORT : 5
Waiting BOOT ack ...
BROM : Skip ACK verify
BROM : Init BROM
BROM init passed!
CHIP : MT6785 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000
CODE : Krug
TYPE : MODERN RAPHAEL
BROM : MEID : 68BB3BDCCF17B153671F368A07599DE0
BROM : SecLevel : 0x000000E7
BROM : SecMode : SBC+SLA+SDA+EXT
BROM : BROM|BL : 0x05|0xFE
BROM : BOOTROM
MODE : 0_base : BASE_v2028 | Manual : Disabled
BROM : SOCID : 430BCAA83754D252FE28C24A05039D895D70599996EA649714 40BC9A8FE45DC5
BROM : SLA : Local Auth
BROM : SLA : Auth Passed!
BROM : SLA : 0x0000001F
AGENT : Look for suitable BootChain in DA ...
AGENT : MTK_AllInOne_DA.bin
AGENT : Found MT6785
AGENT : MTK_DOWNLOAD_AGENT
BROM : Sending 1st DA ...
BROM : DA sent
BROM :Transfer control to DA ...
DA : AGENT started!
DA : SYNC
DA : MODE : BROM
DA : EXT_RAM NOT initialized!
EMI : DEV : INFINITY
EMI : SRC : PRELOADER_INFINITY_0
EMI : CNT : 0001
EMI : Init EMI from INTERNAL DB
EMI : EXT_RAM CFG Passed!
DA : BOOT to 2nd DA ...
DA : 2ND stage confirmed!
DA : SYNC with DA passed!
DA : Receiving HW info
SRAM: 0x00080000 [ 512.00 KB ]
DRAM: 0x180000000 [ 6.00 GB ]
UFS: CE014B4D324837303031434D2D423531
UFS:
VEN : 0x01CE
VID : KM2H7001CM-B51
IFW : 0600
LU0 : 0x00400000 [ 4.00 MB ]
LU1 : 0x00400000 [ 4.00 MB ]
LU2 : 0xEE5800000 [ 59.59 GB ]
FSN : 00330061003800300039006500610039
REG : 0x101010000
CHIP : MT6785 , SBID : 0x8A00 , HWVR : 0xCA00 , SWVR : 0x0000 , EVOL : 0x0000
RNID : 717D7091A59FA02A98D01E2E9ED0CF9
DA : USB : HIGH-SPEED
Boot done!
Memory Info :
CID : KM2H7001CM-B518
EXT_CSD Info :
[UFS] Device Desc:
[UFS] String Desc: Serial Number INDEX 2, LENGTH 24
[UFS] Serial Number: 003300610038003000390065006100390037003800310064
[UFS] life cycle check, pre_eol_info=1, life_time_est_a=1, life_time_est_b=1
[UFS] vendor id : 0x1ce
[UFS] ufs id : KM2H7001CM-B518
[UFS] ufs fwver: 0600
[UFS] dev_quirk = 0x0
[UFS] Custom force provison=0, TW size=-1GB, TW no red=1, HPB size=-1GB
[UFS] info: number of active LU: 3, check OK.
[UFS] info: number of Boot LU: 2, check OK.
[UFS] info: LU Configuration Check OK. Bootable UFS
[UFS] info: Boot LU Configuration Check OK. Active Boot LU: LU0
[UFS] warn: Power on, reset, or bus device reset occupied
[UFS] Sense Data: ASC=29, ASCQ=0
[UFS] warn: Power on, reset, or bus device reset occupied
[UFS] Sense Data: ASC=29, ASCQ=0
[UFS] warn: Power on, reset, or bus device reset occupied
[UFS] Sense Data: ASC=29, ASCQ=0
[UFS] warn: Power on, reset, or bus device reset occupied
[UFS] Sense Data: ASC=29, ASCQ=0
[UFS] info: HS-G3-2
Overall status :
MLC status : 0% - 10% used
SLC status : 0% - 10% used
EOL status : Normal ( Less than 80% reserved blocks used )
RPMB : RPMB KEY NOT set! [State : CLEAN : USABLE]
Done!
Elapsed: 00:00:34 |