GSM-Forum - View Single Post - Post here successfully job with Pandora's

mickeybrown026 · 04-26-2021, 18:57

wrong preloader flashed successfully done best mtk tool ever

Selected model: Mediatek Mediatek
Operation: Flash (Upgrade)
Software version: 1.7

Parse scatter file... OK
Load Rom Images... OK
Host Power Off... OK
Switch virtual port to USB... OK
Connect Type-C to BOX... OK
Host Power On... OK
Wait for device... OK
Read usbhost speed... FULL
Read Device Descriptor...
Get VID/PID...0E8D/0003
Send start cmd... OK
Get HW code from device... 6580
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6580]
Get sec config... OK [00000005]
Active sec flags: [SBC DAA]
Advanced Bypass Security... OK
Disconnect virtual port... OK
Connect Type-C to HUB... OK
Wait for device connecting... OK
Device found at COM41 [BROM]
Open port... OK
Send start cmd... OK
Get HW code from device... 6580
Get HW & SW version from device... OK
HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00
Detect chip [MT6580]
Library Version [1]
Select platform... OK
Init BROM... OK
Force Charge... OK
Disable WatchDog Timer... OK
Load DownloadAgent... OK
ME_ID = 0x513E2F39, 0x85A10C65, 0xA15E0AD8, 0xF52AA3D0
Get sec config... OK [00000000]
Get BROM version... OK
Search DA... OK [12]
Send preloader... OK
Start preloader... OK
Check preloader answer... OK
Send bootloader... OK
Start bootloader... OK
Check bootloader answer... OK
Wait for answer from bootloader... OK
Wait for hw detection... OK
StorageType matched!
Wait DA version... v4.2
Send BROM version... OK
Send storage config... OK
SyncBmtInfoWithDA... OK
Set params... OK
Read flash info... OK
EMMC_ID: 0x460001154D3236451F20034269565F07
Load EMI config from preloader... OK
Init DRAM... OK
Enable DRAM... OK
Sync with DA... OK
Wait for DA H/W detection... OK
EMMC INFO:
EMMC_ID : 0x150100464536324D4203201F075F5669
EMMC_BOOT1: 0x0000400000 (4.00Mb)
EMMC_BOOT2: 0x0000400000 (4.00Mb)
EMMC_RPMB : 0x0000400000 (4.00Mb)
EMMC_USER : 0x03A3E00000 (14.56Gb)
RAM INFO:
INT_SRAM: 0x0000020000 (128.00Kb)
EXT_RAM : 0x0040000000 (1.00Gb)
Check USB status... USB_FULL_SPEED
Switching to USB high speed... OK
Wait for device... OK
High Speed USB detected at COM42
Open port... OK
Check USB status... USB_HIGH_SPEED
Prepare list for upgrade... OK
Check upgrade list... OK
Prepare format list... OK
Prepare final partition list... OK
Read partition preloader... OK
Read partition proinfo... OK
Read partition nvram... OK
Read partition protect1... OK
Read partition protect2... OK
Read partition persist... OK
Verify checksum... OK
Format EMMC_BOOT1_BOOT2 partition... OK
Format EMMC_USER partition... OK
Format EMMC_USER partition... OK
Check sec info... OK
Check SUSBDL Status... enabled
Verify PL... OK
Do BMT remark... OK
Download BootLoader... OK
Update ROM info... OK
Verify "lk"... OK
Secure USB Authenticate Image... OK
Secure USB ImageInfo Check... OK
Verify "lk2"... OK
Secure USB Authenticate Image... OK
Secure USB ImageInfo Check... OK
Verify "boot"... OK
Secure USB Authenticate Image... OK
Secure USB ImageInfo Check... OK
Verify "recovery"... OK
Secure USB Authenticate Image... OK
Secure USB ImageInfo Check... OK
Verify "logo"... OK
Secure USB Authenticate Image... OK
Secure USB ImageInfo Check... OK
Verify "odmdtbo"... OK
Secure USB Authenticate Image... OK
Secure USB ImageInfo Check... OK
Verify "vendor"... OK
Secure USB Authenticate Image... OK
Secure USB ImageInfo Check... OK
Verify "tkv"... OK
Check for unsigned image "tkv"... OK
Verify "tee1"... OK
Secure USB Authenticate Image... OK
Secure USB ImageInfo Check... OK
Verify "tee2"... OK
Secure USB Authenticate Image... OK
Secure USB ImageInfo Check... OK
Verify "secro"... OK
Secure USB Authenticate Image... OK
Secure USB ImageInfo Check... OK
Verify "system"... OK
Secure USB Authenticate Image... OK
Secure USB ImageInfo Check... OK
Verify "cache"... OK
Secure USB Authenticate Image... OK
Secure USB ImageInfo Check... OK
Verify "userdata"... OK
Secure USB Authenticate Image... OK
Secure USB ImageInfo Check... OK
Downloading "lk"... OK
Downloading "lk2"... OK
Downloading "boot"... OK
Downloading "recovery"... OK
Downloading "logo"... OK
Downloading "odmdtbo"... OK
Downloading "vendor"... OK
Downloading "tkv"... OK
Downloading "tee1"... OK
Downloading "tee2"... OK
Downloading "secro"... OK
Downloading "system"... OK
Downloading "cache"... OK
Downloading "userdata"... OK
Verify images checksum... OK
Write SEC CFG... OK
Update ROM info... OK
Check parametres... OK
Write file "proinfo.bin"... OK
Check parametres... OK
Write file "nvram.bin"... OK
Check parametres... OK
Write file "protect1.bin"... OK
Check parametres... OK
Write file "protect2.bin"... OK
Check parametres... OK
Write file "persist.bin"... OK
Flashing done!

04-26-2021, 18:57	#17 (permalink)
mickeybrown026 No Life Poster Join Date: Dec 2016 Location: . Posts: 869 Member: 2659717 Status: Offline Thanks Meter: 487	Tecno B1p dead boot unbrick done wrong preloader flashed successfully done best mtk tool ever Selected model: Mediatek Mediatek Operation: Flash (Upgrade) Software version: 1.7 Parse scatter file... OK Load Rom Images... OK Host Power Off... OK Switch virtual port to USB... OK Connect Type-C to BOX... OK Host Power On... OK Wait for device... OK Read usbhost speed... FULL Read Device Descriptor... Get VID/PID...0E8D/0003 Send start cmd... OK Get HW code from device... 6580 Get HW & SW version from device... OK HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00 Detect chip [MT6580] Get sec config... OK [00000005] Active sec flags: [SBC DAA] Advanced Bypass Security... OK Disconnect virtual port... OK Connect Type-C to HUB... OK Wait for device connecting... OK Device found at COM41 [BROM] Open port... OK Send start cmd... OK Get HW code from device... 6580 Get HW & SW version from device... OK HW VER: CA00, SW VER: 0000, HW SUB CODE: 8A00 Detect chip [MT6580] Library Version [1] Select platform... OK Init BROM... OK Force Charge... OK Disable WatchDog Timer... OK Load DownloadAgent... OK ME_ID = 0x513E2F39, 0x85A10C65, 0xA15E0AD8, 0xF52AA3D0 Get sec config... OK [00000000] Get BROM version... OK Search DA... OK [12] Send preloader... OK Start preloader... OK Check preloader answer... OK Send bootloader... OK Start bootloader... OK Check bootloader answer... OK Wait for answer from bootloader... OK Wait for hw detection... OK StorageType matched! Wait DA version... v4.2 Send BROM version... OK Send storage config... OK SyncBmtInfoWithDA... OK Set params... OK Read flash info... OK EMMC_ID: 0x460001154D3236451F20034269565F07 Load EMI config from preloader... OK Init DRAM... OK Enable DRAM... OK Sync with DA... OK Wait for DA H/W detection... OK EMMC INFO: EMMC_ID : 0x150100464536324D4203201F075F5669 EMMC_BOOT1: 0x0000400000 (4.00Mb) EMMC_BOOT2: 0x0000400000 (4.00Mb) EMMC_RPMB : 0x0000400000 (4.00Mb) EMMC_USER : 0x03A3E00000 (14.56Gb) RAM INFO: INT_SRAM: 0x0000020000 (128.00Kb) EXT_RAM : 0x0040000000 (1.00Gb) Check USB status... USB_FULL_SPEED Switching to USB high speed... OK Wait for device... OK High Speed USB detected at COM42 Open port... OK Check USB status... USB_HIGH_SPEED Prepare list for upgrade... OK Check upgrade list... OK Prepare format list... OK Prepare final partition list... OK Read partition preloader... OK Read partition proinfo... OK Read partition nvram... OK Read partition protect1... OK Read partition protect2... OK Read partition persist... OK Verify checksum... OK Format EMMC_BOOT1_BOOT2 partition... OK Format EMMC_USER partition... OK Format EMMC_USER partition... OK Check sec info... OK Check SUSBDL Status... enabled Verify PL... OK Do BMT remark... OK Download BootLoader... OK Update ROM info... OK Verify "lk"... OK Secure USB Authenticate Image... OK Secure USB ImageInfo Check... OK Verify "lk2"... OK Secure USB Authenticate Image... OK Secure USB ImageInfo Check... OK Verify "boot"... OK Secure USB Authenticate Image... OK Secure USB ImageInfo Check... OK Verify "recovery"... OK Secure USB Authenticate Image... OK Secure USB ImageInfo Check... OK Verify "logo"... OK Secure USB Authenticate Image... OK Secure USB ImageInfo Check... OK Verify "odmdtbo"... OK Secure USB Authenticate Image... OK Secure USB ImageInfo Check... OK Verify "vendor"... OK Secure USB Authenticate Image... OK Secure USB ImageInfo Check... OK Verify "tkv"... OK Check for unsigned image "tkv"... OK Verify "tee1"... OK Secure USB Authenticate Image... OK Secure USB ImageInfo Check... OK Verify "tee2"... OK Secure USB Authenticate Image... OK Secure USB ImageInfo Check... OK Verify "secro"... OK Secure USB Authenticate Image... OK Secure USB ImageInfo Check... OK Verify "system"... OK Secure USB Authenticate Image... OK Secure USB ImageInfo Check... OK Verify "cache"... OK Secure USB Authenticate Image... OK Secure USB ImageInfo Check... OK Verify "userdata"... OK Secure USB Authenticate Image... OK Secure USB ImageInfo Check... OK Downloading "lk"... OK Downloading "lk2"... OK Downloading "boot"... OK Downloading "recovery"... OK Downloading "logo"... OK Downloading "odmdtbo"... OK Downloading "vendor"... OK Downloading "tkv"... OK Downloading "tee1"... OK Downloading "tee2"... OK Downloading "secro"... OK Downloading "system"... OK Downloading "cache"... OK Downloading "userdata"... OK Verify images checksum... OK Write SEC CFG... OK Update ROM info... OK Check parametres... OK Write file "proinfo.bin"... OK Check parametres... OK Write file "nvram.bin"... OK Check parametres... OK Write file "protect1.bin"... OK Check parametres... OK Write file "protect2.bin"... OK Check parametres... OK Write file "persist.bin"... OK Flashing done!