Card found : 80CB8E77 , v0149
Infinity-Box Chinese Miracle II : SPD/USC Module [SP2] v2.13
Load IDBase v8331 Ok!
Open : W6502-F3108-10.0-OP-V029-20210408.pac
VER : BP_R1.0.0
LEN : 2.68 GiB
CPU : sp7731e_1h10
VER : W6502-F3108-10.0-OP-V029-20210408_1645-user
Reading package ...
Read package finished!
Product Brand : Itel
Product Device : W6502
Product Model : itel W6502
Product Name : W6502
Patch Level : QP1A.190711.020
Display ID : W6502-F3108-10.0-OP-V029-20210408
Ver. Incmt : OP-V029-20210408
Ver. CodeName : REL
Ver. Release : 10
Sec. Patch : 2021-04-05
Build Time : 08.04.2021
Product Name : F3108
Product Device : itel-W6502
Product Info : W6502
Product Board : W6502
Board Platform : sp7731e
Product Manfct : itel
Operation : Flash Firmware [ v2.13 ]
Setting : Update NVRAM : False
Setting : Force NVRAM : False
Setting : Update PMT : True
1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!
Wait for device ...
Device Connected!
>>> ERROR : Protocol HandShake failed!
>>> Error : Fail to init protocol!
>>> Remove battery, cable. Check cable and connection. Repeat operation!
Reconnect Power/Cable!
Operation : Flash Firmware [ v2.13 ]
Setting : Update NVRAM : False
Setting : Force NVRAM : False
Setting : Update PMT : True
1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!
Wait for device ...
Device Connected!
BootVersion : SPRD3
Boot : PAC : W6502-F3108-10.0-OP-V029-20210408.pac
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
Boot sent!
Kick FLASH FDL ...
FDL : 0x0008
FDL : EMMC_RO : False ; EMMC_PART : True ; EMMC_RPMB_SET : False
FDL : RAW : 0x0002
FDL : FLH : 0x400000
FDL : SEC : RSA auth required!
FDL : Process authentification ...
FDL : SEC : RSA auth passed!
FDL : Control transfered!
Boot Done!
PMTMng : Load PMT
PMTMng : 0x28
PMTMng : Update PMT Ok!
Prepare target ...
ERROR : 0000008E:80000000FF7F7E00
INT : WAIT TIMEOUT! DEVICE PROBLEM or WRONG FDL!
>>> Error : Flashing failed!
>>> Check previous message for more info!
Reconnect Power/Cable!
Operation : Read FW [ v2.13 ]
Extra : Ignore CriticalPart Verify : Enabled
1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!
Wait for device ...
Device Connected!
BootVersion : SPRD3
Boot : PAC : W6502-F3108-10.0-OP-V029-20210408.pac
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
Boot sent!
Kick FLASH FDL ...
FDL : 0x0008
FDL : EMMC_RO : False ; EMMC_PART : True ; EMMC_RPMB_SET : False
FDL : RAW : 0x0002
FDL : FLH : 0x400000
FDL : SEC : RSA auth required!
FDL : Process authentification ...
FDL : SEC : RSA auth passed!
FDL : Control transfered!
Boot Done!
>>> Error : Device NOT INITIALIZED ! Initialize it first via "IDENTIFY" !
>>> Make sure you have made "IDENTIFY" first!
Reconnect Power/Cable!
Operation : Identify [ v2.13 ]
BootMode : FLASH
1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!
Wait for device ...
Device Connected!
BootVersion : SPRD3
Boot : PAC : W6502-F3108-10.0-OP-V029-20210408.pac
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
Boot sent!
Kick FLASH FDL ...
FDL : 0x0008
FDL : EMMC_RO : False ; EMMC_PART : True ; EMMC_RPMB_SET : False
FDL : RAW : 0x0002
FDL : FLH : 0x400000
FDL : SEC : RSA auth required!
FDL : Process authentification ...
FDL : SEC : RSA auth passed!
FDL : Control transfered!
Boot Done!
Device info :
Product Brand : Itel
Product Device : W6502
Product Model : itel W6502
Product Name : W6502
Patch Level : QP1A.190711.020
Display ID : W6502-F3108-10.0-OP-V029-20210408
Ver. Incmt : OP-V029-20210408
Ver. CodeName : REL
Ver. Release : 10
Sec. Patch : 2021-04-05
Build Time : 08.04.2021
Product Name : F3108
Product Device : itel-W6502
Product Info : W6502
Product Board : W6502
Board Platform : sp7731e
Product Manfct : itel
Platform Version: MOCORTM_17C_W20.21.2_P9_Debug
Project Version: pike2_pub
BASE Version: FM_BASE_17C_W20.21.2_P9
HW Version: sc7731e_modem
CMP_Time : 01-28-2021 11:10:37
MODEM TAG : MOCORTM_17C_W20.21.2_P9_Debug_FM_BASE_17C_W20.21.2 _P9_sc7731e_modem_pike2_pub
USERDATA : FILESYSTEM : F2FS with FDE ( Full Disk Encryption ***)
- > INFO : Remove cable from device to switch it off!
Done!
Elapsed: 00:01:46
Operation : Flash Firmware [ v2.13 ]
Setting : Update NVRAM : True
Setting : Force NVRAM : True
Setting : SlowSparse Fix : True
Setting : Update PMT : True
1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!
Wait for device ...
Device Connected!
>>> ERROR : Protocol HandShake failed!
>>> Error : Fail to init protocol!
>>> Remove battery, cable. Check cable and connection. Repeat operation!
Reconnect Power/Cable!
Operation : Flash Firmware [ v2.13 ]
Setting : Update NVRAM : True
Setting : Force NVRAM : True
Setting : SlowSparse Fix : True
Setting : Update PMT : True
1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!
Wait for device ...
Device Connected!
BootVersion : SPRD3
Boot : PAC : W6502-F3108-10.0-OP-V029-20210408.pac
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
Boot sent!
Kick FLASH FDL ...
FDL : 0x0008
FDL : EMMC_RO : False ; EMMC_PART : True ; EMMC_RPMB_SET : False
FDL : RAW : 0x0002
FDL : FLH : 0x400000
FDL : SEC : RSA auth required!
FDL : Process authentification ...
FDL : SEC : RSA auth passed!
FDL : Control transfered!
Boot Done!
PMTMng : Load PMT
PMTMng : 0x28
PMTMng : Update PMT Ok!
NVRM : pike2_pubcp_PLD_base_nv_nvitem.bin
NVMng : Load 0x17
NVMng : Init SRC
NVMng : SecurityInfo
IMEI[1] : 359471081135014
IMEI[2] : 359471081135014
IMEI[3] : 867400020316638
WIFIMAC : FFFFFFFFFFFF
BT_MAC : FFFFFFFFFFFF
SEC : SLS:0, SKS:0, SKV:4
NVMng : Backup Ok , 0x00066B50
NVMng : Init DST
NVMng : Rx11 : Wx10
NVMng : NVM block updated!
Prepare target ...
ERROR : 0000008E:80000000FF7F7E00
INT : WAIT TIMEOUT! DEVICE PROBLEM or WRONG FDL!
>>> Error : Flashing failed!
>>> Check previous message for more info!
Reconnect Power/Cable!
Operation : Flash Firmware [ v2.13 ]
Setting : Update NVRAM : True
Setting : Force NVRAM : True
Setting : SlowSparse Fix : True
Setting : Update PMT : True
1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!
Wait for device ...
Device Connected!
BootVersion : SPRD3
Boot : PAC : W6502-F3108-10.0-OP-V029-20210408.pac
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
Boot sent!
Kick FLASH FDL ...
FDL : 0x0008
FDL : EMMC_RO : False ; EMMC_PART : True ; EMMC_RPMB_SET : False
FDL : RAW : 0x0002
FDL : FLH : 0x400000
FDL : SEC : RSA auth required!
FDL : Process authentification ...
FDL : SEC : RSA auth passed!
FDL : Control transfered!
Boot Done!
PMTMng : Load PMT
PMTMng : 0x28
PMTMng : Update PMT Ok!
NVRM : pike2_pubcp_PLD_base_nv_nvitem.bin
NVMng : Load 0x17
NVMng : Init SRC
NVMng : SecurityInfo
IMEI[1] : 359471081135014
IMEI[2] : 359471081135014
IMEI[3] : 867400020316638
WIFIMAC : FFFFFFFFFFFF
BT_MAC : FFFFFFFFFFFF
SEC : SLS:0, SKS:0, SKV:4
NVMng : Backup Ok , 0x00066B50
NVMng : Init DST
NVMng : Rx11 : Wx10
NVMng : NVM block updated!
Prepare target ...
ERROR : 0000008E:80000000FF7F7E00
INT : WAIT TIMEOUT! DEVICE PROBLEM or WRONG FDL!
>>> Error : Flashing failed!
>>> Check previous message for more info!
Reconnect Power/Cable!
Operation : Format FS / Reset Settings [ v2.13 ]
Mode : Forced [ Format FS / Fix ]
BootMode : FLASH
1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!
Wait for device ...
Device Connected!
BootVersion : SPRD3
Boot : PAC : W6502-F3108-10.0-OP-V029-20210408.pac
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
Boot sent!
Kick FLASH FDL ...
FDL : 0x0008
FDL : EMMC_RO : False ; EMMC_PART : True ; EMMC_RPMB_SET : False
FDL : RAW : 0x0002
FDL : FLH : 0x400000
FDL : SEC : RSA auth required!
FDL : Process authentification ...
FDL : SEC : RSA auth passed!
FDL : Control transfered!
Boot Done!
Wipe Ok : Forced Wipe
Wipe Ok : Forced Wipe
Reconnect Power/Cable!
Done!
Elapsed: 00:01:51
Operation : Flash Firmware [ v2.13 ]
Setting : Update NVRAM : True
Setting : Force NVRAM : True
Setting : SlowSparse Fix : True
Setting : Update PMT : True
Setting : WholeFLASH FORMAT : True
1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!
Wait for device ...
Device Connected!
BootVersion : SPRD3
Boot : PAC : W6502-F3108-10.0-OP-V029-20210408.pac
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
Boot sent!
Kick FLASH FDL ...
FDL : 0x0008
FDL : EMMC_RO : False ; EMMC_PART : True ; EMMC_RPMB_SET : False
FDL : RAW : 0x0002
FDL : FLH : 0x400000
FDL : SEC : RSA auth required!
FDL : Process authentification ...
FDL : SEC : RSA auth passed!
FDL : Control transfered!
Boot Done!
ERASE : FORMAT WHOLE FLASH ...
ERASE : FORMAT FLASH Completed!
PMTMng : Load PMT
PMTMng : 0x28
PMTMng : Update PMT Ok!
NVRM : pike2_pubcp_PLD_base_nv_nvitem.bin
NVMng : Load 0x17
NVMng : Init SRC
NVMng : Trying use recover mode
NVMng : Security DAMAGED!
NVMng : Backup Ok , 0x00100000
NVMng : Trying use recover mode
NVMng : Init DST
NVMng : NV has been destroyed! Forced Update enabled! Repair security after!
NVMng : NVM block updated!
Prepare target ...
ERROR : 0000008E:80000000FF7F7E00
INT : WAIT TIMEOUT! DEVICE PROBLEM or WRONG FDL!
>>> Error : Flashing failed!
>>> Check previous message for more info!
Reconnect Power/Cable!
Operation : Flash Firmware [ v2.13 ]
Setting : Update NVRAM : False
Setting : Force NVRAM : False
Setting : Update PMT : False
1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!
Wait for device ...
Device Connected!
BootVersion : SPRD3
Boot : PAC : W6502-F3108-10.0-OP-V029-20210408.pac
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
Boot sent!
Kick FLASH FDL ...
FDL : 0x0008
FDL : EMMC_RO : False ; EMMC_PART : True ; EMMC_RPMB_SET : False
FDL : RAW : 0x0002
FDL : FLH : 0x400000
FDL : SEC : RSA auth required!
FDL : Process authentification ...
FDL : SEC : RSA auth passed!
FDL : Control transfered!
Boot Done!
Prepare target ...
ERROR : 0000008E:80000000FF7F7E00
INT : WAIT TIMEOUT! DEVICE PROBLEM or WRONG FDL!
>>> Error : Flashing failed!
>>> Check previous message for more info!
Reconnect Power/Cable!
flashing failed any help |