| After cleaning, should i Flash the same dump as before in Emmc Manager with Security Unticked ?
Running:SAMSUNG: eMMC firmware update...
Chip Init OK...
Operation cancelled by user!
Operation canceled by user!
Running:SAMSUNG: eMMC firmware update...
Chip Init OK...
Downloading FFU:C:\Program Files\Z3X\EASYJTAG\eMMC Firmware\KMDP6001DA-B425_DP6DAB_Rev3.bin
Checking security ...
Z3X EasyJtag Software ver. 3.8.0.1
Checking firmware type...
OK;
Skip loading eMMC Addon Firmware
Box S/N: D41BF4FDB081B5EF, ,FW Ver.: 02.53
CMD Pullup Level:2196 mV
CMD Active Level:2342 mV
Box IO Level:2800 mV
CLK Rate:18000 kHz
Using firmware file : C:\Program Files\Z3X\EASYJTAG\eMMC Firmware\KMDP6001DA-B425_DP6DAB_Rev3.bin
Update Firmware ID Hash:
Setup firmware update mode, wait 2..30 sec...
Success!
Sending eMMC firmware...
Success!
Verifying eMMC firmware...
Success!
Flashing eMMC firmware...
Success!
eMMC CID : 15010044503644414200A1D5D3E44997
New CID : 150100445036444142036FB3D23D7793
Repairing eMMC CID...
eMMC CSD : D02701320F5903FFF6DBFFEF8E40400D
Repairing eMMC CSD...
Success!
eMMC firmware is updated now!
Please don't forget to repair extCSD from backup!
Please don't forget to configure BOOT sizes!
Done.
-----------------------------
Setting interface to EasyJtag2/ISP_HiPower
Setting bus width to 1 Bit
HiPower mode is ON
Setting frequence to 18 MHz
CMD Pullup Level: 1854 mV
CMD Active Level: 1879 mV
EMMC Device Information :
EMMC CID: 150100445036444130031D02D23D7777
EMMC CSD: D02701320F5903FFF6DBFFEF8E40400D
EMMC Manufacture : SAMSUNG , EMMC NAME: DP6DA0 , HEX: 445036444130 , S/N: 1D02D23D , rev. 0x03
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 7/2020
EMMC ROM 1 (Main User Data) Capacity: 59640 MB (000E8F800000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 16384 KB (000001000000) Counter: 0 , Response: Clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG]: 0x00 , Boot from: no boot
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: DP6DA0_1D02D23D_20221117_195244.extcsd
EMMC Init completed. |