GSM-Forum - View Single Post

Ashim Ashram · 03-08-2023, 06:51

HELLO, I AM WORKING ON A135F AND I POSSES 2 PIECES. HOWEVER WHEN I TRY TO CONNECT THEM THE BOX SAYS EMMC DEAD YET CONNECTING SUCCESSFULLY WITH UFI. I TRIED CHANGING PC AND UPDATING CARD FIRMWARE BUT TO KNOW AVAIL. PLEASE ADVISE ACCORDINGLY

Setting interface to EasyJtag2/ISP
Setting bus width to 1 Bit
Setting frequence to 36 MHz
CMD Pullup Level: 1813 mV
CMD Active Level: 1865 mV
EMMC Device Information :
EMMC CID: 150100303030303030562016061354D1
EMMC CSD: 902701320F5903FFF6DB7FE08A40403B
EMMC Manufacture : SAMSUNG , EMMC NAME: 000000 , HEX: 303030303030 , S/N: 20160613 , rev. 0x56
EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 5/2017
EMMC ROM 1 (Main User Data) Capacity: 2095982 MB (01FFB6E00000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 512 KB (000000080000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 KB (000000020000) Counter: 0 , Response: Maybe not clean
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG]: 0x00 , Boot from: no boot
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x03
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
EMMC Init completed.

Warning: Maybe your emmc damaged

eMMC are unusable.

03-08-2023, 06:51	#1 (permalink)
Ashim Ashram Freak Poster Join Date: Dec 2017 Location: Uganda Posts: 105 Member: 2793734 Status: Offline Thanks Meter: 22	Box connection a135f HELLO, I AM WORKING ON A135F AND I POSSES 2 PIECES. HOWEVER WHEN I TRY TO CONNECT THEM THE BOX SAYS EMMC DEAD YET CONNECTING SUCCESSFULLY WITH UFI. I TRIED CHANGING PC AND UPDATING CARD FIRMWARE BUT TO KNOW AVAIL. PLEASE ADVISE ACCORDINGLY Setting interface to EasyJtag2/ISP Setting bus width to 1 Bit Setting frequence to 36 MHz CMD Pullup Level: 1813 mV CMD Active Level: 1865 mV EMMC Device Information : EMMC CID: 150100303030303030562016061354D1 EMMC CSD: 902701320F5903FFF6DB7FE08A40403B EMMC Manufacture : SAMSUNG , EMMC NAME: 000000 , HEX: 303030303030 , S/N: 20160613 , rev. 0x56 EMMC Manufacture ID: 0x15 , OEM ID: 0x00 , Device Type: BGA (Discrete embedded) , Date: 5/2017 EMMC ROM 1 (Main User Data) Capacity: 2095982 MB (01FFB6E00000) EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 512 KB (000000080000) EMMC RPMB (Replay Protected Memory Block) Capacity: 128 KB (000000020000) Counter: 0 , Response: Maybe not clean EMMC Permanent Write Protection: No EMMC Temporary Write Protection: No Extended CSD Information : Extended CSD rev: 1.5 (MMC 4.41) Boot configuration [PARTITION_CONFIG]: 0x00 , Boot from: no boot Boot Bus Config: 0x00 , width 1bit H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled Supported partition features [PARTITIONING_SUPPORT]: 0x03 Device supports partitioning features Device can have enhanced technological features in partitions and user data area Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00 EMMC Init completed. Warning: Maybe your emmc damaged eMMC are unusable.