GSM-Forum - View Single Post

janjaroen · 08-23-2006, 15:38

I RESIVE DEAD PHONE FROM CUSTOMER
FIST TIME I FLASH OK BUT PHONE SHOW MASSAGE no SERVICE AFTER INSERT SIM AND POWER ON HOW CAN I DO.THANK

COM5 selected
Device: BenQ M315, Siemens AP75
Checking data, wait...
Action: Flash write
Smart Write active
Write: Firmware
Write: Flex
Skip: Language Pack
Write: Eeprom
Boot...
Phone should be Switched OFF !
Connect test-point to Ground !
Press Power button now !
Connecting...
Disconnect test-point !
Boot Done
Check Connection...
Check Connection Done
Set Baud...
Set Baud Done
Check Flash...
Check Flash Done
Check Parameters...
Check Parameters Done
Check Space...
Err: unknown flash chip: 0010:0010:0010:0010
Err: unknown flash chip: 1470:5571:5438:0020
Err: unknown flash chip: 3200:3200:3200:2200
Check Space Fail
Finished
Remove/Install battery now !
Time used: 36 sec

WHEN I UNLOCK

COM5 selected
Device: BenQ M315, Siemens AP75
Checking data, wait...
Action: Unlock
Boot...
Phone should be Switched OFF !
Connect test-point to Ground !
Press Power button now !
Connecting...
Disconnect test-point !
Boot Done
Check Connection...
Check Connection Done
Set Baud...
Set Baud Done
Check Flash...
Check Flash Done
Check Parameters...
Err: unknown flash chip: 0010:0010:0010:0010
Flash: 0089:885500010001
file saved: Backup_eeprom-00_2006-8-23_21-41-9.4BF.bin
Err: not locked or unknown eeprom
Check Parameters Fail
Finished
Remove/Install battery now !
Time used: 38 sec

08-23-2006, 15:38	#1 (permalink)
janjaroen Registered User Join Date: Aug 2005 Location: www.siamgsmunlock.com Posts: 379 Member: 175926 Status: Offline Thanks Meter: 25	Benq M315 Cannot Flash I RESIVE DEAD PHONE FROM CUSTOMER FIST TIME I FLASH OK BUT PHONE SHOW MASSAGE no SERVICE AFTER INSERT SIM AND POWER ON HOW CAN I DO.THANK COM5 selected Device: BenQ M315, Siemens AP75 Checking data, wait... Action: Flash write Smart Write active Write: Firmware Write: Flex Skip: Language Pack Write: Eeprom Boot... Phone should be Switched OFF ! Connect test-point to Ground ! Press Power button now ! Connecting... Disconnect test-point ! Boot Done Check Connection... Check Connection Done Set Baud... Set Baud Done Check Flash... Check Flash Done Check Parameters... Check Parameters Done Check Space... Err: unknown flash chip: 0010:0010:0010:0010 Err: unknown flash chip: 1470:5571:5438:0020 Err: unknown flash chip: 3200:3200:3200:2200 Check Space Fail Finished Remove/Install battery now ! Time used: 36 sec WHEN I UNLOCK COM5 selected Device: BenQ M315, Siemens AP75 Checking data, wait... Action: Unlock Boot... Phone should be Switched OFF ! Connect test-point to Ground ! Press Power button now ! Connecting... Disconnect test-point ! Boot Done Check Connection... Check Connection Done Set Baud... Set Baud Done Check Flash... Check Flash Done Check Parameters... Err: unknown flash chip: 0010:0010:0010:0010 Flash: 0089:885500010001 file saved: Backup_eeprom-00_2006-8-23_21-41-9.4BF.bin Err: not locked or unknown eeprom Check Parameters Fail Finished Remove/Install battery now ! Time used: 38 sec Last edited by janjaroen; 08-23-2006 at 18:06.