| Why Still Dead
I have got one E66 china with dead condition. Customer says he lissting songs and his mobile shut down. I have format it with complete but same. Now i dont know what is the problem. And dont know which firmware is inside
here is log.
COM4 [VCP0] selected
module v3.11
Device: Autodetect 6205-6227 NOR
Checking data, wait...
advanced flash detection enabled
Action: reset settings ("format ffs")
Do you want to make ffs/eeprom backup before format ?
====> Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6225:8A05:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:FF0F:FFFF
status: 01
boot packet size: 0400
Release Power button now !
Boot Done
====> Initialize ...
detecting chip #00 in region #00...
flash: 89887E00040004:89887E00000000
flash: 89887E00040004:89887E00000000
flash: Intel 512MBit non-mux U 64Mb
otp offset: 00000000
number of flash chip/regions detected: 01/01
Initialize Done
====> Set baud ...
115200
Set baud Done
====> Initialize bootcode ...
Initialize bootcode Done
====> Check firmware integrity ...
device parameters detection in progress...
detecting chip #00 in region #00...
flash: 89887E00040004:89887E00000000
flash: 89887E00040004:89887E00000000
flash: Intel 512MBit non-mux U 64Mb
otp offset: 00000000
number of flash chip/regions detected: 01/01
total flash region size: 04000000
usb bootloader detect...
..
usb bootloader detect (phase #2)...
..
usb bootloader (chip) is absent
searching rom info...
.
search rom info finished
searching rom info...
.
search rom info finished
warning: rom info information not found, possible reasons:
- old firmware type w/o rom info information
- empty (completely or partially erased) flash chip
- damaged firmware
- damaged hardware (bad soldered or damaged flash chip)
> if phone works fine just ignore this warning <
detecting ffs/eeprom area in 1 chip(s)...
standard ffs/eeprom offset assigned: 03C00000
flash: 89887E00040004:89887E00000000
flash: 89887E00040004:89887E00000000
checking area [00000000]: 00080000-03FFFFFF...
Can't detect ffs/eeprom area
Do you want to use standard ffs/eeprom address: 03C00000 ?
If you are not sure that standard address is correct:
1. press "NO" and terminate current operation
2. make flash backup for emergency case
3. repeat required operation
standard ffs/eeprom address selected by user
detecting ffs/eeprom size...
ffs/eeprom size: 00400000
ffs/eeprom chip: 00
ffs/eeprom area: 00000000:03C00000-03FFFFFF
sec info (detailed) detection...
searching sec info#1...
.
search sec info#1 finished
Check firmware integrity Done
====> Check firmware content ...
Check firmware content Done
====> Backup required data ...
flash: 89887E00040004:89887E00000000
flash: 89887E00040004:89887E00000000
Backup required data Done
====> Patch required data ...
Patch required data Done
====> Special operation ...
Special operation Done
====> Write ...
Write Done
====> Finalization ...
ffs formatting...
flash: 89887E00040004:89887E00000000
flash: 89887E00040004:89887E00000000
Finalization Done
Finished, time used: 52 sec
Remove/Install battery now !
File system has been modified !
It is need to press and HOLD phone "Power" button
during long time (up to 1 min) to make phone Powered-On ! |