| try to "default imei inside firmware"
COM6 [VCP1] selected
module v3.27
Device: Autodetect 6205-6239 NOR
Checking data, wait...
advanced flash detection enabled
Action: "repair imei"
imei write channel: imei #1 (default imei inside firmware)
new imei: 910001493712258
====> Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6225:8A05:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:6C03:0001
status: FF
boot packet size: 0400
Release Power button now !
Boot Done
====> Initialize ...
detecting chip #00 in region #00...
flash: 2088C4FFFF0043:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
otp offset: 00FE0000
detecting chip #01 in region #00...
flash: 2088C4FFFF0043:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
otp offset: 00FE0000
detecting chip #02 in region #00...
flash: 2088C4FFFF0043:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
otp offset: 00FE0000
detecting chip #03 in region #00...
flash: 2088C4FFFF0043:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
otp offset: 00FE0000
number of flash chip/regions detected: 04/01
Initialize Done
====> Set baud ...
115200
Set baud Done
====> Initialize bootcode ...
Initialize bootcode Done
====> Check firmware integrity ...
device parameters detection in progress...
detecting chip #00 in region #00...
flash: 2088C4FFFF0043:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
otp offset: 00FE0000
detecting chip #01 in region #00...
flash: 2088C4FFFF0043:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
otp offset: 00FE0000
it's time to stop: 18F09FE518F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
usb bootloader detect...
..
usb bootloader detect (phase #2)...
..
usb bootloader (chip) is absent
searching rom info...
search rom info finished
rom info structure: [standard] type (04)
TCL-ID is absent
rom info detection finished
rom info ver: 04
sw version: DEWAV25_07B_GEMINI_Z868_PCB01_GPRS_MT6225_S00.INTE X_IN4495_Z808_Z808_L404_5M4.BIN
project-id: INTEX_IN4495_Z808_Z808_L404_5M4, 00000000
code offset: 00000000
ffs offset/size [01]: 00E00000/00200000
rom info structure: [standard] type (04)
TCL-ID is absent
detecting ffs/eeprom area in 1 chip(s)...
standard ffs/eeprom offset detected: 00E00000
standard ffs/eeprom offset confirmed: 00E00000
detecting ffs/eeprom size...
ffs/eeprom size: 00200000
ffs/eeprom chip: 00
ffs/eeprom area: 00000000:00E00000-00FFFFFF
firmware area: 00000000-00DFFFFF
detecting startup code area #2...
.................................................. .................................................. .................................................. .................................................. .................................................. ......
startup code area #2 is absent
sec info (detailed) detection...
searching sec info#1...
.
search sec info#1 finished
Check firmware integrity Done
====> Check firmware content ...
Check firmware content Done
====> Backup required data ...
flash: 2088C4FFFF0043:2088C400000000
Backup required data Done
====> Patch required data ...
detecting ffs/eeprom structure pass 2...
............................
ffs/eeprom: detect std location pass #1...
.................................................. .
ffs/eeprom: detect standard offset pass #1...
ffs/eeprom record offset detected
ffs/eeprom: detect standard data...
ffs/eeprom record size detected
ffs/eeprom layout detection complete
ffs/eeprom detected ok element #2
imei default found: 13579024681122
Patch required data Done
====> Special operation ...
Special operation Done
====> Write ...
flash: 2088C4FFFF0043:2088C400000000
flash: 2088C4FFFF0043:2088C400000000
Write: imei
Write Done
====> Finalization ...
ffs formatting...
flash: 2088C4FFFF0043:2088C400000000
Finalization Done
Finished, time used: 2 min 57 sec
Remove/Install battery now !
File system has been modified !
It is need to press and HOLD phone "Power" button
during long time (up to 1 min) to make phone Powered-On !
Action: read/check information
Model: Autodetect 6205-6239 NOR
Checking data, wait...
Phone should be Switched ON !
Connecting, wait...
Phone detected, wait...
Hardware version: MT6225, E05
Hardware version: DEWAV25_07B_GEMINI_HW
Software version: INTEX_IN4495_Z808_Z8
Software date: 2006.06.14
Barcode: MT012345678901234567
imei-1: 000000000000000
imei-2: 000000000000000
imei-3: 000000000000000
Finished, time used: 14 sec
Remove/Install battery now !
Imei 91000149371225 already was repaired: 3/15/2011-11:26:52 AM
Continue with this imei ?
Action: "repair imei"
Model: Autodetect 6205-6239 NOR
Checking data, wait...
Phone should be Switched ON !
Connecting, wait...
Phone detected, wait...
imei-1: 000000000000000
imei write method: mode-1
imei write channel: imei #1 for dual sim/mono CPU
new imei-1: 910001493712258
verification Ok
Finished, time used: 3 sec
Remove/Install battery now !
Imei 91000149371225 already was repaired: 3/15/2011-11:29:41 AM
Continue with this imei ?
Action: "repair imei"
Model: Autodetect 6205-6239 NOR
Checking data, wait...
Phone should be Switched ON !
Connecting, wait...
Phone detected, wait...
imei-1: 910001493712258
imei write method: mode-1
imei write channel: imei #1 for dual sim/mono CPU
new imei-1: 910001493712258
verification Ok
Finished, time used: 7 sec
Remove/Install battery now !
Action: read/check information
Model: Autodetect 6205-6239 NOR
Checking data, wait...
Phone should be Switched ON !
Connecting, wait...
Phone detected, wait...
Hardware version: MT6225, E05
Hardware version: DEWAV25_07B_GEMINI_HW
Software version: INTEX_IN4495_Z808_Z8
Software date: 2006.06.14
Barcode: MT012345678901234567
imei-1: 000000000000000
imei-2: 000000000000000
imei-3: 000000000000000
Finished, time used: 3 sec
Remove/Install battery now !
Imei 91000149371225 already was repaired: 3/15/2011-11:30:12 AM
Continue with this imei ?
==== [3/15/2011 11:30:32 AM] ====
COM6 [VCP1] selected
module v3.27
Action: "repair imei"
imei write method: mode-2
imei write channel: imei #1 for dual sim/mono CPU
new imei: 910001493712258
Model: Autodetect 6205-6239 NOR
Checking data, wait...
Phone should be Switched OFF !
Press and HOLD Power button now !
19200 autodetect
Initializing [6225:8A05:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:6C03:0001
status: FF
Connecting at 19200, wait...
Release Power button now !
Phone detected, wait...
Hardware: MT6225,E05
Date: 2006.06.14
Version: 1.0
Version: INTEX_IN4495_Z808_Z808_L404_5M4
Version: DEWAV25_07B_GEMINI_HW
detecting structure #2...
5 11 done
67 byte(s) read
imei: 00000000000000
connection Ok
detecting structure #2...
5 11 done
67 byte(s) read
verification...
verification done: 91000149371225
Finished, time used: 20 sec
Remove/Install battery now !
Action: read/check information
Model: Autodetect 6205-6239 NOR
Checking data, wait...
Phone should be Switched ON !
Connecting, wait...
Phone detected, wait...
Hardware version: MT6225, E05
Hardware version: DEWAV25_07B_GEMINI_HW
Software version: INTEX_IN4495_Z808_Z8
Software date: 2006.06.14
Barcode: MT012345678901234567
imei-1: 910001493712258
imei-2: 000000000000000
imei-3: 910001493712258
Finished, time used: 3 sec
Remove/Install battery now !
Imei 91000149371225 already was repaired: 3/15/2011-11:30:59 AM
Continue with this imei ?
==== [3/15/2011 11:31:41 AM] ====
COM6 [VCP1] selected
module v3.27
Device: Autodetect 6205-6239 NOR
Checking data, wait...
advanced flash detection enabled
Action: "repair imei"
imei write method: mode-3
imei write channel: imei #1 for dual sim/mono CPU
new imei: 910001493712258
ffs/eeprom backup enabled, it may takes several minutes !
====> Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6225:8A05:8A00]...
CPU: MT6225
high speed boot On
chip: 0001:6C03:0001
status: FF
boot packet size: 0400
Release Power button now !
Boot Done
====> Initialize ...
detecting chip #00 in region #00...
flash: 2088C4FFFF0043:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
otp offset: 00FE0000
detecting chip #01 in region #00...
flash: 2088C4FFFF0043:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
otp offset: 00FE0000
detecting chip #02 in region #00...
flash: 2088C4FFFF0043:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
otp offset: 00FE0000
detecting chip #03 in region #00...
flash: 2088C4FFFF0043:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
otp offset: 00FE0000
number of flash chip/regions detected: 04/01
Initialize Done
====> Set baud ...
115200
Set baud Done
====> Initialize bootcode ...
Initialize bootcode Done
====> Check firmware integrity ...
device parameters detection in progress...
detecting chip #00 in region #00...
flash: 2088C4FFFF0043:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
otp offset: 00FE0000
detecting chip #01 in region #00...
flash: 2088C4FFFF0043:2088C400000000
flash: ST Intel/Sharp ext [def 007Fx020000 0004x008000] 16Mb
otp offset: 00FE0000
it's time to stop: 18F09FE518F09FE518F09FE518F09FE518F09FE518F09FE5
number of flash chip/regions detected: 01/01
total flash region size: 01000000
usb bootloader detect...
..
usb bootloader detect (phase #2)...
..
usb bootloader (chip) is absent
searching rom info...
search rom info finished
rom info structure: [standard] type (04)
TCL-ID is absent
rom info detection finished
rom info ver: 04
sw version: DEWAV25_07B_GEMINI_Z868_PCB01_GPRS_MT6225_S00.INTE X_IN4495_Z808_Z808_L404_5M4.BIN
project-id: INTEX_IN4495_Z808_Z808_L404_5M4, 00000000
code offset: 00000000
ffs offset/size [01]: 00E00000/00200000
rom info structure: [standard] type (04)
TCL-ID is absent
detecting ffs/eeprom area in 1 chip(s)...
standard ffs/eeprom offset detected: 00E00000
standard ffs/eeprom offset confirmed: 00E00000
detecting ffs/eeprom size...
ffs/eeprom size: 00200000
ffs/eeprom chip: 00
ffs/eeprom area: 00000000:00E00000-00FFFFFF
firmware area: 00000000-00DFFFFF
detecting startup code area #2...
.................................................. .................................................. .................................................. .................................................. .................................................. ......
startup code area #2 is absent
sec info (detailed) detection...
searching sec info#1...
.
search sec info#1 finished
Check firmware integrity Done
====> Check firmware content ...
Check firmware content Done
====> Backup required data ...
reading: DEWAV25_07B_GEMINI_Z868_PCB01_GPRS_MT6225_S00.INTE X_IN4495_Z808_Z808_L404_5M4__ffs...
file saved: C:\InfinityBox\ChineseMiracle\DEWAV25_07B_GEMINI_Z 868_PCB01_GPRS_MT6225_S00.INTEX_IN4495_Z808_Z808_L 404_5M4__ffs_20110315-113707.B0E.bin
flash: 2088C4FFFF0043:2088C400000000
Backup required data Done
====> Patch required data ...
30 step(s) required
Patch required data Done
====> Special operation ...
Special operation Done
====> Write ...
flash: 2088C4FFFF0043:2088C400000000
Write: ffs
Write Done
====> Finalization ...
Finalization Done
Finished, time used: 6 min 4 sec
Remove/Install battery now !
Action: read/check information
Model: Autodetect 6205-6239 NOR
Checking data, wait...
Phone should be Switched ON !
Connecting, wait...
Phone detected, wait...
Hardware version: MT6225, E05
Hardware version: DEWAV25_07B_GEMINI_HW
Software version: INTEX_IN4495_Z808_Z8
Software date: 2006.06.14
Barcode: MT012345678901234567
imei-1: 000000000000000
imei-2: 000000000000000
imei-3: 000000000000000
Finished, time used: 4 sec
Remove/Install battery now |