| [9/14/2012 3:29:31 PM] [START OPERATION_ID = DCC_WRITE_MEMORY]
[9/14/2012 3:29:32 PM]
[9/14/2012 3:29:32 PM] Current Settings:
[9/14/2012 3:29:32 PM] -----------------
[9/14/2012 3:29:32 PM] Address: 000000000000
[9/14/2012 3:29:32 PM] Length: 000000008000
[9/14/2012 3:29:32 PM] Address Space: ROM2
[9/14/2012 3:29:32 PM] AutoFullFlash: UNCHECKED
[9/14/2012 3:29:32 PM] Use End Address: UNCHECKED
[9/14/2012 3:29:32 PM] ECC Module Enabled: UNCHECKED
[9/14/2012 3:29:32 PM] Image File is Used: UNCHECKED
[9/14/2012 3:29:32 PM] Use Address as Offset: CHECKED
[9/14/2012 3:29:32 PM] Main (CHECKED): C:\GSM NEW\Riff Box\I777 boot\I777 boot.bin
[9/14/2012 3:29:32 PM] Redu (UNCHECKED):
[9/14/2012 3:29:32 PM]
[9/14/2012 3:29:41 PM] Open serial port...OK
[9/14/2012 3:29:41 PM] Connecting to the RIFF Box...OK
[9/14/2012 3:29:41 PM] Firmware Version: 1.33, JTAG Manager Version: 1.44
[9/14/2012 3:29:41 PM] Selected Resurrector: [Samsung i777 V1.0.0.0]
[9/14/2012 3:29:41 PM]
[9/14/2012 3:29:41 PM] Connecting to the dead body...OK
[9/14/2012 3:29:41 PM] Detected dead body ID: 0x4BA00477 - CORRECT!
[9/14/2012 3:29:41 PM] Set I/O Voltage reads as 2.80V, TCK Frequency is 8 MHz
[9/14/2012 3:29:41 PM] Settings Code: 0x22020B00000000000000000000008000
[9/14/2012 3:29:41 PM]
[9/14/2012 3:29:41 PM] Resurrection sequence started.
[9/14/2012 3:29:41 PM] Establish communication with the phone...OK
[9/14/2012 3:29:41 PM] Initializing internal hardware configuration...OK
[9/14/2012 3:29:41 PM] Uploading resurrector data into memory...OK
[9/14/2012 3:29:41 PM] Starting communication with resurrector...OK
[9/14/2012 3:29:41 PM]
[9/14/2012 3:29:41 PM] Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0001 (VYL00M, 0x0003AB400000 Bytes = 14.68 GB)
[9/14/2012 3:29:41 PM] Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0001 (VYL00M, 0x000000080000 Bytes = 0.50 MB)
[9/14/2012 3:29:41 PM]
[9/14/2012 3:29:41 PM] Writting FLASH2 memory from 0x000000000000 to 0x000000007FFF
[9/14/2012 3:29:41 PM] Completed in 00:00:04.860 (Average Transfer Rate: 6.58 kB/s)
[9/14/2012 3:29:41 PM] [FINISH OPERATION_ID = DCC_WRITE_MEMORY]
[9/14/2012 3:30:55 PM] [START OPERATION_ID = DCC_WRITE_MEMORY]
[9/14/2012 3:30:55 PM]
[9/14/2012 3:30:55 PM] Current Settings:
[9/14/2012 3:30:55 PM] -----------------
[9/14/2012 3:30:55 PM] Address: 000000008000
[9/14/2012 3:30:55 PM] Length: 000000008000
[9/14/2012 3:30:55 PM] Address Space: ROM2
[9/14/2012 3:30:55 PM] AutoFullFlash: UNCHECKED
[9/14/2012 3:30:55 PM] Use End Address: UNCHECKED
[9/14/2012 3:30:55 PM] ECC Module Enabled: UNCHECKED
[9/14/2012 3:30:55 PM] Image File is Used: UNCHECKED
[9/14/2012 3:30:55 PM] Use Address as Offset: CHECKED
[9/14/2012 3:30:55 PM] Main (CHECKED): C:\GSM NEW\Riff Box\I777 boot\I777 boot.bin
[9/14/2012 3:30:55 PM] Redu (UNCHECKED):
[9/14/2012 3:30:55 PM]
[9/14/2012 3:31:01 PM] Open serial port...OK
[9/14/2012 3:31:01 PM] Connecting to the RIFF Box...OK
[9/14/2012 3:31:01 PM] Firmware Version: 1.33, JTAG Manager Version: 1.44
[9/14/2012 3:31:01 PM] Selected Resurrector: [Samsung i777 V1.0.0.0]
[9/14/2012 3:31:01 PM]
[9/14/2012 3:31:01 PM] Connecting to the dead body...OK
[9/14/2012 3:31:01 PM] Detected dead body ID: 0x4BA00477 - CORRECT!
[9/14/2012 3:31:01 PM] Set I/O Voltage reads as 2.80V, TCK Frequency is 8 MHz
[9/14/2012 3:31:01 PM] Settings Code: 0x22020B00000000008000000000008000
[9/14/2012 3:31:01 PM]
[9/14/2012 3:31:01 PM] Resurrection sequence started.
[9/14/2012 3:31:01 PM] Establish communication with the phone...OK
[9/14/2012 3:31:01 PM] Initializing internal hardware configuration...OK
[9/14/2012 3:31:01 PM] Uploading resurrector data into memory...OK
[9/14/2012 3:31:01 PM] Starting communication with resurrector...OK
[9/14/2012 3:31:01 PM]
[9/14/2012 3:31:01 PM] Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0001 (VYL00M, 0x0003AB400000 Bytes = 14.68 GB)
[9/14/2012 3:31:01 PM] Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0001 (VYL00M, 0x000000080000 Bytes = 0.50 MB)
[9/14/2012 3:31:01 PM]
[9/14/2012 3:31:01 PM] Writting FLASH2 memory from 0x000000008000 to 0x00000000FFFF
[9/14/2012 3:31:01 PM] Completed in 00:00:04.516 (Average Transfer Rate: 7.09 kB/s)
[9/14/2012 3:31:01 PM] [FINISH OPERATION_ID = DCC_WRITE_MEMORY]
[9/14/2012 3:31:15 PM] [START OPERATION_ID = DCC_WRITE_MEMORY]
[9/14/2012 3:31:15 PM]
[9/14/2012 3:31:15 PM] Current Settings:
[9/14/2012 3:31:15 PM] -----------------
[9/14/2012 3:31:15 PM] Address: 000000010000
[9/14/2012 3:31:15 PM] Length: 000000008000
[9/14/2012 3:31:15 PM] Address Space: ROM2
[9/14/2012 3:31:15 PM] AutoFullFlash: UNCHECKED
[9/14/2012 3:31:15 PM] Use End Address: UNCHECKED
[9/14/2012 3:31:15 PM] ECC Module Enabled: UNCHECKED
[9/14/2012 3:31:15 PM] Image File is Used: UNCHECKED
[9/14/2012 3:31:15 PM] Use Address as Offset: CHECKED
[9/14/2012 3:31:15 PM] Main (CHECKED): C:\GSM NEW\Riff Box\I777 boot\I777 boot.bin
[9/14/2012 3:31:15 PM] Redu (UNCHECKED):
[9/14/2012 3:31:15 PM]
[9/14/2012 3:31:21 PM] Open serial port...OK
[9/14/2012 3:31:21 PM] Connecting to the RIFF Box...OK
[9/14/2012 3:31:21 PM] Firmware Version: 1.33, JTAG Manager Version: 1.44
[9/14/2012 3:31:21 PM] Selected Resurrector: [Samsung i777 V1.0.0.0]
[9/14/2012 3:31:21 PM]
[9/14/2012 3:31:21 PM] Connecting to the dead body...OK
[9/14/2012 3:31:21 PM] Detected dead body ID: 0x4BA00477 - CORRECT!
[9/14/2012 3:31:21 PM] Set I/O Voltage reads as 2.80V, TCK Frequency is 8 MHz
[9/14/2012 3:31:21 PM] Settings Code: 0x22020B00000000010000000000008000
[9/14/2012 3:31:21 PM]
[9/14/2012 3:31:21 PM] Resurrection sequence started.
[9/14/2012 3:31:21 PM] Establish communication with the phone...OK
[9/14/2012 3:31:21 PM] Initializing internal hardware configuration...OK
[9/14/2012 3:31:21 PM] Uploading resurrector data into memory...OK
[9/14/2012 3:31:21 PM] Starting communication with resurrector...OK
[9/14/2012 3:31:21 PM]
[9/14/2012 3:31:21 PM] Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0001 (VYL00M, 0x0003AB400000 Bytes = 14.68 GB)
[9/14/2012 3:31:21 PM] Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0001 (VYL00M, 0x000000080000 Bytes = 0.50 MB)
[9/14/2012 3:31:21 PM]
[9/14/2012 3:31:21 PM] Writting FLASH2 memory from 0x000000010000 to 0x000000017FFF
[9/14/2012 3:31:21 PM] Completed in 00:00:04.359 (Average Transfer Rate: 7.34 kB/s)
[9/14/2012 3:31:21 PM] [FINISH OPERATION_ID = DCC_WRITE_MEMORY]
[9/14/2012 3:31:58 PM] [START OPERATION_ID = DCC_WRITE_MEMORY]
[9/14/2012 3:31:58 PM]
[9/14/2012 3:31:58 PM] Current Settings:
[9/14/2012 3:31:58 PM] -----------------
[9/14/2012 3:31:58 PM] Address: 000000018000
[9/14/2012 3:31:58 PM] Length: 000000008000
[9/14/2012 3:31:58 PM] Address Space: ROM2
[9/14/2012 3:31:58 PM] AutoFullFlash: UNCHECKED
[9/14/2012 3:31:58 PM] Use End Address: UNCHECKED
[9/14/2012 3:31:58 PM] ECC Module Enabled: UNCHECKED
[9/14/2012 3:31:58 PM] Image File is Used: UNCHECKED
[9/14/2012 3:31:58 PM] Use Address as Offset: CHECKED
[9/14/2012 3:31:58 PM] Main (CHECKED): C:\GSM NEW\Riff Box\I777 boot\I777 boot.bin
[9/14/2012 3:31:58 PM] Redu (UNCHECKED):
[9/14/2012 3:31:58 PM]
[9/14/2012 3:32:04 PM] Open serial port...OK
[9/14/2012 3:32:04 PM] Connecting to the RIFF Box...OK
[9/14/2012 3:32:04 PM] Firmware Version: 1.33, JTAG Manager Version: 1.44
[9/14/2012 3:32:04 PM] Selected Resurrector: [Samsung i777 V1.0.0.0]
[9/14/2012 3:32:04 PM]
[9/14/2012 3:32:04 PM] Connecting to the dead body...OK
[9/14/2012 3:32:04 PM] Detected dead body ID: 0x4BA00477 - CORRECT!
[9/14/2012 3:32:04 PM] Set I/O Voltage reads as 2.80V, TCK Frequency is 8 MHz
[9/14/2012 3:32:04 PM] Settings Code: 0x22020B00000000018000000000008000
[9/14/2012 3:32:04 PM]
[9/14/2012 3:32:04 PM] Resurrection sequence started.
[9/14/2012 3:32:04 PM] Establish communication with the phone...OK
[9/14/2012 3:32:04 PM] Initializing internal hardware configuration...OK
[9/14/2012 3:32:04 PM] Uploading resurrector data into memory...OK
[9/14/2012 3:32:04 PM] Starting communication with resurrector...OK
[9/14/2012 3:32:04 PM]
[9/14/2012 3:32:04 PM] Detected an Initialized FLASH1 Chip, ID: 0x0015/0x0001 (VYL00M, 0x0003AB400000 Bytes = 14.68 GB)
[9/14/2012 3:32:04 PM] Detected an Initialized FLASH2 Chip, ID: 0x0015/0x0001 (VYL00M, 0x000000080000 Bytes = 0.50 MB)
[9/14/2012 3:32:04 PM]
[9/14/2012 3:32:04 PM] Writting FLASH2 memory from 0x000000018000 to 0x00000001FFFF
[9/14/2012 3:32:04 PM] Completed in 00:00:04.359 (Average Transfer Rate: 7.34 kB/s)
[9/14/2012 3:32:04 PM] [FINISH OPERATION_ID = DCC_WRITE_MEMORY]
I tryed the trick with boot.bin extracted from an I777 original flash tar not working. I also had multiple error 0x3E. After pc restart it worked but still brick.
I think this is a total brick. Corrupt Nand. Any other ideas I'm willing to try.
Thanks everybody for the ideas so far. |