[saqib2009]

her is log local sx4 see


Phone found!
Series 40 Device detected!
read info... - Ok

Local SX4 procedure started...

Check SD : Key is Ok
Phone Imei: 356852025304662
Key file exists, no need to read...
Step 1...
Step 2...
Step 3...
SX4 Auth - Ok
Upload PM checked
Uploading RF/Battery tune to phone...
Using : RM-237.pm
Operating mode is OK, no need change...


Check ST_SECURITY now...
Security status : ST_SECURITY => DAMAGED
- > Try "Restore CCC/HWC" option, after SX4 again

Done!

Elapsed: 00:00:06

Upload done


and upload tune log see


Uploading RF/Battery tune to phone...
Using : RM-237.pm
Operating mode is OK, no need change...


Check ST_SECURITY now...
Security status : ST_SECURITY => DAMAGED
- > Try "Restore CCC/HWC" option, after SX4 again

Done!

Elapsed: 00:00:06

and then i try restore ccc/hwc see log

Will Write CCC/HWC keys now...

Using : RM-237.rpl
CCC Data found!
HWC Data found!

Setting FlashMode
FlashMode set Ok

1st boot Ok, C0

CMT part info :
CMT ASICID : 000000010000022600010006010C192101001101
CMT EM0 ID : 00000232
CMT EM1 ID : 00000353
CMT PUB ID : 22400119EAA87C568CF96405E6AB5C485B716FDC
CMT MODE ID : 00
CMT R_HASH : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID : 191EC665DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg , Rev : 0.0 Ver : 10.42.0
CMT Loader sent, Boot Ok
MCU Configuration
MCU Cfg Ok , 03
FLASHID : 89810089 , CMT , NOR
CMT Flash ID : 89810089 < INTEL => NU48F256
FLCNT : 00000000000000000000000000000000000000
FLASHID : 0000FFFF , CMT , MMC , EXT
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
Sending ALGO....
Use : RAP3Gv3_algo_v1331.fg , Rev : 0.0 Ver : 1.33.1
CMT Algo sent
CMT PAPUB : C0E691EA16A7593A9BB28832D7312A39F7ED668D05
Transmission mode : Dual (Ddr, TX2)

Boot Done!

Preparing for write certificates...

CMT : CCC erase Ok
Writing CCC... Ok

CMT : HWC erase Ok
Writing HWC... Ok


Done!

Elapsed: 00:00:16

Connect phone on selected interface...

Phone found!
Series 40 Device detected!
read info... - Ok


then again bus check

Will Write CCC/HWC keys now...

Using : RM-237.rpl
CCC Data found!
HWC Data found!

Setting FlashMode
FlashMode set Ok

1st boot Ok, C0

CMT part info :
CMT ASICID : 000000010000022600010006010C192101001101
CMT EM0 ID : 00000232
CMT EM1 ID : 00000353
CMT PUB ID : 22400119EAA87C568CF96405E6AB5C485B716FDC
CMT MODE ID : 00
CMT R_HASH : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID : 191EC665DFAAF68F

CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg , Rev : 0.0 Ver : 10.42.0
CMT Loader sent, Boot Ok
MCU Configuration
MCU Cfg Ok , 03
FLASHID : 89810089 , CMT , NOR
CMT Flash ID : 89810089 < INTEL => NU48F256
FLCNT : 00000000000000000000000000000000000000
FLASHID : 0000FFFF , CMT , MMC , EXT
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
Sending ALGO....
Use : RAP3Gv3_algo_v1331.fg , Rev : 0.0 Ver : 1.33.1
CMT Algo sent
CMT PAPUB : C0E691EA16A7593A9BB28832D7312A39F7ED668D05
Transmission mode : Dual (Ddr, TX2)

Boot Done!

Preparing for write certificates...

CMT : CCC erase Ok
Writing CCC... Ok

CMT : HWC erase Ok
Writing HWC... Ok


Done!

Elapsed: 00:00:16

Connect phone on selected interface...

Phone found!
Series 40 Device detected!
read info... - Ok


My Problem not solved ???