Hello All..
I searched the forum and looked at the same problems but I couldn't figure it out..
Phone was ok before I just wanted to change imei because of registration law in Turkey.
Resurrection was ok here is the log (Repair CID to 11111111 - Repair ime zone - Repair recovery zones unchecked - Reflash Total HTC partition during imei repair unchecked):
Code:
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.34, JTAG Manager Version: 1.48
Selected Resurrector: [HTC WildfireS V1.0.4522.55486]
Connecting to the dead body...OK
Detected dead body ID: 0x203C10E1 - CORRECT!
Set I/O Voltage reads as 2.59V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK
Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x66BC (512MB)
Selected Resurrection Data for the NAND Chip with Page size = 4KB
Flashing the dead body...OK
Resurrection complete!
After resurrection phone fastboot info is:
MARVEL PVT SHIP S-ON RL
HBOOT-0.90.0000
MICROP-0451
RADIO-7.46.35.08
Apr 8 2011,17:45:10
and I flashed RUU_Marvel_S_HTC_Europe_2.13.401.3_Radio_47.23c.35 .3037_7.54.39.28M_release_236989_signed.exe
While it flashes from MMC it said
Main Version is older!
Update Fail!
So I tryed RUU_Marvel_S_HTC_Europe_2.26.401.3_Radio_47.23e.35 .3038H_7.57.39.10M_release_261695_signed.exe
and flash ok :
but phone blinks..
So I dissamble the phone again and erase flash(Acces Rom1 address space selected- Auto Full flash size checked) :
Code:
Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.34, JTAG Manager Version: 1.48
Selected Resurrector: [HTC WildfireS V1.0.4522.55486]
Connecting to the dead body...OK
Detected dead body ID: 0x203C10E1 - CORRECT!
Set I/O Voltage reads as 2.59V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]
Settings Code: 0x04010000000000000000000020000000
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK
Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x66BC (512MB)
Erasing FLASH1 memory from 0x000000000000 to 0x00001FFFFFFF...OK
Completed in 00:00:08.156 (Average Transfer Rate: 64282.49 kB/s)
And then I resurrect again (Repair CID to 11111111 - Repair ime zone - Repair recovery zones unchecked - Reflash Total HTC partition during imei repair unchecked):
Code:
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK
Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x66BC (512MB)
Selected Resurrection Data for the NAND Chip with Page size = 4KB
Flashing the dead body...FAILED
ERROR: Resurrection is not Completed due to Error: 0x3901
It gived this error and I checked Reflash Total HTC partition during imei repair :
Code:
Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK
Detected an Initialized FLASH1 Chip, ID: 0x00EC/0x66BC (512MB)
Selected Resurrection Data for the NAND Chip with Page size = 4KB
Flashing the dead body...OK
Resurrection complete!
So I assemble the phone again and reflash from mmc
When it flashes bootloader it says "Can not roll back hboot version"
and again phone just blinks at the beginning and can't enter hboot..
I also flashed "WildFireS_Full_alive.bin" and "wildfire_S(2.3.5...S-OFF_Super-CID_working_Dump).bin" nothing changed.
When it flashes wildfire_S(2.3.5...S-OFF_Super-CID_working_Dump).bin it stuck at %11..
Any help will be so gratefull..
Thanks