6210 totally dead, please help - GSM-Forum

weiss77 · 04-15-2003, 08:58

I got a 6210, and don't know what happened to this phone. It is totally dead, there is no signal in the display, also no display when i connect it to the power supply. What can i do?Rolis says, that no mobile is detected at the cable.... Any idea?

GazI · 04-16-2003, 13:35

check batery

weiss77 · 04-17-2003, 12:35

very funny. I did it already, the battery is new and there's still nothing

GazI · 04-17-2003, 18:48

hi try to write MCU+PPM+virgin eeprom

and clear cabel contact

weiss77 · 04-18-2003, 13:45

Which prog would you prefer and will I need a Flasher Cable or is the M/Fbus Cable enough?

GazI · 04-18-2003, 16:59

hi

try with this software rolis 4.78

http://www.crackingworld.de/gsmfree/...flasher478.zip

and use flasher cabel

dydycom · 07-11-2003, 20:18

I've experienced some problems with that flasher . Try to use v5.14 with not to small delay, anyway check the pins on the phone, clear them of any dirt and use dejan old flasher cable( with 74hc 14 inside not with pic). That should work, but my opinion is that the phone ram memory pins, some of them ar not soldered(oxid) and you will get "phone ram bad" or try to reflow the ccont. POst results!

intersoft · 12-12-2003, 13:19

give some testing point to check that power section is ok or not

04-15-2003, 08:58	#1 (permalink)
weiss77 Junior Member Join Date: Jan 2003 Age: 47 Posts: 16 Member: 19603 Status: Offline Thanks Meter: 0	6210 totally dead, please help I got a 6210, and don't know what happened to this phone. It is totally dead, there is no signal in the display, also no display when i connect it to the power supply. What can i do?Rolis says, that no mobile is detected at the cable.... Any idea?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
c55 totally dead please help	Toriniasty	Siemens Hardware Repair Area	15	11-29-2004 12:49
My TSM5m is totally locked, please, help!	mia-x	Phone Unlocking Codes & Maps	0	02-04-2004 16:09
C55 totally Dead plz help	x4ce	E-Gold Based Phones	8	12-27-2003 03:45
6210 v3.04 dead please help	shedz	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	2	12-28-2001 22:02
totally dead T10. Help!!	alfonsraven	Old Ericsson Phones & Sony Phones	0	07-27-2000 22:06

04-16-2003, 13:35	#2 (permalink)
GazI No Life Poster Join Date: Jan 2003 Location: KOSOVA Age: 37 Posts: 1,278 Member: 20566 Status: Offline Thanks Meter: 29	check batery

04-17-2003, 12:35	#3 (permalink)
weiss77 Junior Member Join Date: Jan 2003 Age: 47 Posts: 16 Member: 19603 Status: Offline Thanks Meter: 0	very funny. I did it already, the battery is new and there's still nothing

04-17-2003, 18:48	#4 (permalink)
GazI No Life Poster Join Date: Jan 2003 Location: KOSOVA Age: 37 Posts: 1,278 Member: 20566 Status: Offline Thanks Meter: 29	hi try to write MCU+PPM+virgin eeprom and clear cabel contact

04-18-2003, 13:45	#5 (permalink)
weiss77 Junior Member Join Date: Jan 2003 Age: 47 Posts: 16 Member: 19603 Status: Offline Thanks Meter: 0	Which prog would you prefer and will I need a Flasher Cable or is the M/Fbus Cable enough?

04-18-2003, 16:59	#6 (permalink)
GazI No Life Poster Join Date: Jan 2003 Location: KOSOVA Age: 37 Posts: 1,278 Member: 20566 Status: Offline Thanks Meter: 29	hi try with this software rolis 4.78 http://www.crackingworld.de/gsmfree/...flasher478.zip and use flasher cabel

07-11-2003, 20:18	#7 (permalink)
dydycom Freak Poster Join Date: Jan 2003 Location: hell (gsm bussines) Age: 49 Posts: 142 Member: 19875 Status: Offline Thanks Meter: 3	I've experienced some problems with that flasher . Try to use v5.14 with not to small delay, anyway check the pins on the phone, clear them of any dirt and use dejan old flasher cable( with 74hc 14 inside not with pic). That should work, but my opinion is that the phone ram memory pins, some of them ar not soldered(oxid) and you will get "phone ram bad" or try to reflow the ccont. POst results!

12-12-2003, 13:19	#8 (permalink)
intersoft Freak Poster Join Date: Dec 2003 Location: india Age: 51 Posts: 101 Member: 46212 Status: Offline Thanks Meter: 0	give some testing point to check that power section is ok or not