Corrupted eeprom data in 3210

[cole]

Hi,

Phone was OK till one day when I whant to power it up,It write CONTCAT SERVICE.I remove battery and try again but same problem.<br />I red phone with NTools and here is result:

MCU SW = v6.00 ....etc<br />IMEI =449314203540145 (like on stick under batt.)<br />Orginal IMEI = 656565653540145 <img src="frown.gif" border="0"> <img src="frown.gif" border="0"> <img src="frown.gif" border="0"> <br />Sec.Code = 00000 (it was 12345 when phone was working) <img src="frown.gif" border="0"> <img src="frown.gif" border="0"> <img src="frown.gif" border="0"> <br />MCC+MNC = FF000<br />GID 1 = 0000<br />GID 2 = 0000<br />MSIN = 0000000000<br />and all lock closed !!!<br />I read full flash and compare it with good one,flash is OK.<br />I read eeprom with pony and try to fix it with Bartek and Guar,but that didn`t resole problem.<br />Now I have damaged data,from no reason,in eeprom that I don`t know how to fix it <img src="mad.gif" border="0"> <img src="mad.gif" border="0"> <br />I try to reset phone with all posible tools and WinTesla and etc...but nothing helped.<br />I know that is hard to fix it,but is there any posibility or do you have any sugestion.???

Thanks<br />B.R<br />Cole

P.S.<br />Phone have orginal flash I mean it wasn`t ever upgrader or changed language even it was never locked.

[cole]

Hi,

What a lovely day <img src="smile.gif" border="0"> <img src="smile.gif" border="0"> <img src="smile.gif" border="0"> <br />Phone is fixed.Gues how <img src="biggrin.gif" border="0"> <img src="biggrin.gif" border="0"> <img src="biggrin.gif" border="0">

Regards

[simonb]

Go ON tell us how:

[mr_x4you]

I know, but I won't tell !!!! He He He !!! <img src="biggrin.gif" border="0"> <img src="biggrin.gif" border="0"> <img src="biggrin.gif" border="0">

[Mad4IT]

Come on!!! Tell us how is it fixed????

Anyway...you said you read the EEPROM with Pony...was it just with the MBUS cable or do you need any special tool??<br />Can you at least answer that?!?!?<br />Thanx!

[Xepuis]

Come on, read flasher topics!

Thx, Dejan!

[cole]

Hi

You can`t read eeprom with M-Bus.Eeprom inside 3210 is in separate part that calls eeprom.<br />Eprom in newer versions of Nokia`s is emulated in flash.So when yo read flash you read and "eeprom".

I don`t whan`t to tell how I fix my phone <img src="tongue.gif" border="0"> <img src="tongue.gif" border="0"> <br />Come on friends don`t be funy.Last night Dejan give us...... <img src="biggrin.gif" border="0"> <img src="biggrin.gif" border="0"> <img src="biggrin.gif" border="0">

Regards

[mudboy]

You CAN read eeprom area with MBUS,but you CAN'T read security area of EEPROM:-((<br />regards

[ 25 February 2002: Message edited by: mudboy ]</p>

[DAVI]

Use Nk_cal from dejan

[neb]

And this is my guess!!

Procedure on how to repair 3210 CS with corrupted IMEIs:

1. Re flash MCU and PPM to make sure both datas are good.

2. Open the unit, locate and remove eeprom chip 24c128. Write
a good 3210 eeprom data using ponyprog. Verify the process, if unsuccessfull, use a new chip.

3. Re install the re prog 24C128 chip.

4. Turn on the unit, CS now removed, but locks are still closed
and will not accept any simcard. AND NOW!!

5. Run nk_calcu (15,000USD=free). Press F1, F2 (use sticker IMEI if you wish) and F3.

6. Put sim, power it on, unit will reset after a while and "you've got a working phone".

7. Run Nokia Tool by Koci, change original IMEI if both are different. Apply SFS with Koci or Nokia Tool by Pro.

8. Re check, if it fails, re run nk_calcu. Press F1, F2 and F3.

9. THAT's IT.

Regards,

[cole]

Hi,

I do it just like you write.Phone isa still working OK.


Regards