Repair signal dropping after IMEI ch! - GSM-Forum

gyuszko · 03-02-2002, 03:30

Signal dropping repair after IMEI change with NK_calc
--------------------------------------------------------------------

1. Connect phone and power on!
2. Press F2 (IMEI change) and input your IMEI number.
3. After sw. says done,disconnect phone and switch off!
4. Wait 10 secs and power on phone.Repeat power off and on steps again!
5. Connect phone again to m2bus and hit F3 (SP clear).
6. After sw. finished working,repeat power off and on steps 2 times.
7. Your phone will stay on network now if there was no hardware failure.
8. Additional:change Original IMEI to match with current IMEI if you want.

BR,
- Gyuszko aka. The CodeMaster -

Tested on 6210 and 7110

Ps: maybe this will not help ya all,but I hope in most cases will repair this idiot bug...

xmans · 03-09-2002, 10:09

Hi.
I just flashed 8850 with full flash with eeprom by dejan 1.0. After that I used dejan dct3 eeprom repair. But phone couldn't logon to network. Only operator name appear then disappear. Also reboot. I pressed many times alI buttons nk_calc. But still same. How I repair my phone? Is it faid calculation for 8850 doesn't work? Or I flashed bad flash image? Please more describe your solution? DOes bphreak eeprom tool also have this bug?
Bye.

Brobble · 03-09-2002, 15:50

after every use of nk_calc you must reset factory values and make software reset! Just use this tool Just start tool, read phone, seleclt "UI Settings", press "Apply SFS" and make "SW Reset"! Now your phone should work perfect! If not, mail me privat!

Greetings MR...

gamalabel · 03-11-2002, 06:06

Hello, I tested that in a 8210 and the phone work again. good work "gyuszko"

xmans · 03-11-2002, 08:33

Hi.
After upgrading new version works fine.
Bye

bharat paryani · 03-11-2002, 15:35

hello there mates!!! can u give me the proper software to use in this topic!! send it to my e-mail add at [email protected] tnx in advance!!!

03-02-2002, 03:30	#1 (permalink)
gyuszko Product Supporter Join Date: Dec 2001 Location: in my skin Age: 47 Posts: 1,213 Member: 8086 Status: Offline Thanks Meter: 180	Repair signal dropping after IMEI ch! Signal dropping repair after IMEI change with NK_calc -------------------------------------------------------------------- 1. Connect phone and power on! 2. Press F2 (IMEI change) and input your IMEI number. 3. After sw. says done,disconnect phone and switch off! 4. Wait 10 secs and power on phone.Repeat power off and on steps again! 5. Connect phone again to m2bus and hit F3 (SP clear). 6. After sw. finished working,repeat power off and on steps 2 times. 7. Your phone will stay on network now if there was no hardware failure. 8. Additional:change Original IMEI to match with current IMEI if you want. BR, - Gyuszko aka. The CodeMaster - Tested on 6210 and 7110 Ps: maybe this will not help ya all,but I hope in most cases will repair this idiot bug...

03-09-2002, 10:09	#2 (permalink)
xmans Freak Poster Join Date: Aug 2001 Location: 43543 Posts: 224 Member: 5792 Status: Offline Thanks Meter: 1	after imie change no network 8850? Hi. I just flashed 8850 with full flash with eeprom by dejan 1.0. After that I used dejan dct3 eeprom repair. But phone couldn't logon to network. Only operator name appear then disappear. Also reboot. I pressed many times alI buttons nk_calc. But still same. How I repair my phone? Is it faid calculation for 8850 doesn't work? Or I flashed bad flash image? Please more describe your solution? DOes bphreak eeprom tool also have this bug? Bye.

03-11-2002, 08:33	#5 (permalink)
xmans Freak Poster Join Date: Aug 2001 Location: 43543 Posts: 224 Member: 5792 Status: Offline Thanks Meter: 1	Thanks Hi. After upgrading new version works fine. Bye

03-11-2002, 15:35	#6 (permalink)
bharat paryani Junior Member Join Date: Dec 2001 Location: philippines Posts: 20 Member: 7699 Status: Offline Thanks Meter: 0	what software?? hello there mates!!! can u give me the proper software to use in this topic!! send it to my e-mail add at [email protected] tnx in advance!!!

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
K608I signal drops after couple of hours	rey_astrophil	Sony Ericsson Hardware Repair	0	05-20-2008 10:29
Nokia 3220 Signal Problem after Imei Repair	vintercell	Universalbox	6	05-04-2006 13:36
8330 signal drop after few secs ... ??	TRABEL	LG	4	08-16-2005 23:31
3310 Signal drops after few seconde from powering ???!!	crown	Nokia Hardware & Hardware Repair	14	01-08-2005 20:20
6230 signal drops after a few seconds	jabran200	Nokia Hardware & Hardware Repair	12	12-25-2004 13:21

03-09-2002, 15:50	#3 (permalink)
Brobble No Life Poster Join Date: Oct 2000 Posts: 547 Member: 2274 Status: Offline Thanks Meter: 0	after every use of nk_calc you must reset factory values and make software reset! Just use this tool Just start tool, read phone, seleclt "UI Settings", press "Apply SFS" and make "SW Reset"! Now your phone should work perfect! If not, mail me privat! Greetings MR...

03-11-2002, 06:06	#4 (permalink)
gamalabel Insane Poster Join Date: Jun 2001 Location: Portugal Posts: 91 Member: 4908 Status: Offline Thanks Meter: 1	Hello, I tested that in a 8210 and the phone work again. good work "gyuszko"