Motorolla Test ? Cut Point

[adnanali]

plz manage a motorolla test point....cut point.................and details Section WE hope that you do this jobe. thanks for gsm-hosting really a BEST DATA FORUM IN THE WORLD THANKS TO ALL

[adnanali]

[B] Latest versions:
Smart-Clip v2.23 (30.03.06)
SmartMoto v1.18 (30.03.06)








Operation instruction
Sendo snd2xx/snd3xx/snd5xx/snd6xx/snd8xx unlocking procedure
Unlock procedure for V557 phone with testpoint
Unlock procedure for E1070 phone with testpoint
Unlock procedure for A1000 phone with testpoint
Unlock procedure for E770 and V3x phone with testpoint
Unlocking V3 (boot ver.8.26)
Unlocking V1050, V975 (ver R245_xxx) (inc. boot 0.6.1.2) and others models with boot 0.6.3.1
V18x/V22x/C65x/C38x/E375/E378i (newer versions), C975/C980/V980/E1000 (Boot Loader 0.6.1.2) unlocking note
Unlock procedure for A920/A925/A1000
Axxx/Exxx/Vxxx unlocking note
E396/E398 unlocking note
C115/C116/C117/C155/C156/E365/V170/V171 unlocking procedure
Unlock procedure for V3 (RAZR) phone by downgrading boot using testpoint (boot version 8.26)
Unlock procedure for C975 phone with testpoint (boot versions starting from 6.36)
Unlock procedure for C980 phone with testpoint (boot versions starting from 6.36)
Unlock procedure for E1000 phone with testpoint (boot versions starting from 6.36)
Unlock procedure for V975 phone with testpoint (boot versions starting from 6.36)
Unlock procedure for V980 phone with testpoint (boot versions starting from 6.36)
Unlock procedure for V1050 phone with testpoint (boot versions starting from 6.36)
Unlock procedure for C390 phone with testpoint (boot version 8.26)
Unlock procedure for V360 phone with testpoint (boot versions starting from 8.A0)
Unlock procedure for E1, L6, L7, U6, V190 phone with testpoint
Unlock procedure for V3i phone with testpoint (boot versions starting from 8.A0)
Smart-Clip upgrade procedure
Operation instruction(standard unlock procedure for P2K models)
Power on the Smart-Clip and E/G indicator will light green.
Power on the phone without SIM card and flash card (if present).
Connect phone to Smart-Clip and press the "Unlock" button ( red on older clips ).
E/G indicator will light green and go off, the phone will switch off (some models will automatically turn on then).
E/G will light green on success or red on error
Successful unlock resets User Code to 1234, Security Code to 000000
Pinout P2K to USB A Standard Cable
Pinout P2K to USB A Forced Boot Mode Cable

Sendo snd2xx/snd3xx/snd5xx/snd6xx/snd8xx unlocking procedurePower off the phone
Connect clip to the phone using RJ45 cable (pinouts below)
Press UNLOCK button
Press Power button on the phone within 5 seconds after you press UNLOCK button on a clip. RX/TX leds will blink
E/G led will glow green on success.
When you unlock Sendo phone use either fully charged phone battery OR power supply from Smart-Clip. Don't use them both at the same time! If you use power supply from Smart-Clip, make sure current is not less than 300mA, otherwise not all data will be properly recorded to the phone.
Pinout Sendo snd2xx snd3xx snd6xx
Pinout Sendo snd5xx
Pinout Sendo snd8xx

Unlock procedure for V557 phone with testpointUsing "Unlock via Testpoint" function of SmartMoto method
Perform V557 testpoint procedure
Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Unlock procedure for E1070 phone with testpointUsing "Unlock via Testpoint" function of SmartMoto method
Perform E1070 testpoint procedure
Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Unlock procedure for A1000 phone with testpointUsing "Unlock via Testpoint" function of SmartMoto method
Disassemble the phone
Connect repair USB cable (pin 13 and 14 shortened)
Connect testpoint A to testpoint B
Connect phone battery
Push Button 1 and Button 2 simultaneously
Press "Search" button in SmartMoto
SmartMoto should find "S Blank Paragon POG", or "S Blank Rainbow POG"
Disconnect testpoint
Open unlock tab in SmartMoto
Select A1000 from phone models list
Press "unlock via testpoint"
The handset is unlocked & ready to be assembled.
Unlock procedure for E770 and V3x phone with testpointUsing "Unlock via Testpoint" function of SmartMoto method
Perform corresponding testpoint procedure
Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab

Please remember:
During testpoint unlocking procedure phone's LCD must be disconnected.
Do not use hot air fan to remove a metal shield on PCB. This can seriously damage the handset.
Use any other alternative tool to cut or drill it. Please make sure you do not damage the board.

Unlocking V3 (boot ver.8.26)You need to use SmartMoto to unlock these models.
Power on the phone.
Connect it to PC via smart-clip, detect your phone in SmartMoto.
Go to Unlock bookmark, pick your model, press "Remove RSA" button.
Phone goes into boot mode.
Part of phone firmware is reflashed.
The phone powers on and is ready to be unlocked by Smart-Clip using simple "press one button" method (press Unlock button on Smart-Clip).

Unlocking V1050, V975 (ver R245_xxx) (inc. boot 0.6.1.2) and others models with boot 0.6.3.1You need to use SmartMoto to unlock these models.
Power on the phone.
Connect it to PC via smart-clip, detect your phone in SmartMoto.
Go to Unlock bookmark, pick your model, press "Remove RSA" button.
Phone goes into boot mode, reserve copy of security area is created.
Part of phone firmware is reflashed.
Phone doesn't power on after that. SmartMoto will give you the message requiring to take phone into boot mode using keys combination: *,#, PWR ON (at this moment the phone has to be connected by usb cable) or using Repairing cable.
Press "OK" button. Wait till the process ends.
The phone powers on and is ready to be unlocked by Smart-Clip using simple "press one button" method (press Unlock button on Smart-Clip).

V18x/V22x/C65x/C38x/E375/E378i (newer versions), C975/C980/V980/E1000 (Boot Loader 0.6.1.2) unlocking noteUnlocking newer versions of V18x/V22x/C65x/C38x/E375/E378i or C975/C980/V980/E1000 (Boot Loader 0.6.1.2) may require additional user intervention.
It may happen that E/G led still blinks after display turns off - it means that you have to turn the phone ON manually within 2-3 seconds after display turns off; alternatively you can try to unlock this newer version of V18x/V22x/C65x/C38x/E375/E378i with battery charger on.




Unlock procedure for A920/A925/A1000Power the phone on.
Connect the phone to a powered clip. Phone display should give "USB cable connected" message.
Press UNLOCK button on the clip.
Phone reloads. Within 5-10 seconds phone display gives "Waiting for PST" message.
Press 1 and 2 keys simultaneously in upper part of the handset. The phone enters boot mode (if you don't press these 2 keys during "Waiting for PST" message, the clip will give red E/G led and you will have to start with step 1 again).
After A and B keys have been pressed E/G green led will blink and phone reboots. Meanwhile E/G will give frequent green blinking and phone will turn on.
Do not disconnect cell phone from Smart-Clip while green led indicator blinks!
Green E/G led glows. The cell phone is unlocked.

Axxx/Exxx/Vxxx unlocking noteDon't unplug cable right after phone reboot, wait until E/G led stops blinking!



E396/E398 unlocking noteRemove flash card from phone before unlocking



C115/C116/C117/C155/C156/E365/V170/V171 unlocking procedurePower off the phone
Connect clip to the phone using RJ45 cable (pinouts below)
Press UNLOCK button
Press Power button on the phone within 5 seconds after you press UNLOCK button on a clip. RX/TX leds will blink
E/G led will glow green on success *
* After successful unlock (green led on) phones with inserted sim card may ask for PCK or NCK code. Enter 00000000 ("zero" 8 times)
Pinout C115 C116 C117 C155 C156 V170 V171
Pinout E365

Unlock procedure for V3 (RAZR) phone by downgrading boot using testpoint (boot version 8.26)Perform V3 testpoint procedure
Flash it with V3_boot_7.E.0.smf file.
Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.

Unlock procedure for C975 phone with testpoint (boot versions starting from 6.36)Downgrade boot method
Perform C975 testpoint procedure
Flash it with C975_boot_5.F.1.smf file
Turn the handset by pressing keys * # PowerON and perform "Remove RSA" procedure
Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.

Using "Unlock via Testpoint" function of SmartMoto method
Perform C975 testpoint procedure
Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab

Unlock procedure for C980 phone with testpoint (boot versions starting from 6.36)Downgrade boot method
Perform C980 testpoint procedure
Flash it with C980_boot_5.F.1.smf file
Turn the handset by pressing keys * # PowerON and perform "Remove RSA" procedure
Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.

Using "Unlock via Testpoint" function of SmartMoto method
Perform C980 testpoint procedure
Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab

Unlock procedure for E1000 phone with testpoint (boot versions starting from 6.36)Downgrade boot method
Perform E1000 testpoint procedure
Flash it with E1000_boot_5.F.1.smf file
Turn the handset by pressing keys * # PowerON and perform "Remove RSA" procedure
Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.

Using "Unlock via Testpoint" function of SmartMoto method
Perform E1000 testpoint procedure
Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab

Unlock procedure for V975 phone with testpoint (boot versions starting from 6.36)Downgrade boot method
Perform V975 testpoint procedure
Flash it with V975_boot_5.F.1.smf file
Turn the handset by pressing keys * # PowerON and perform "Remove RSA" procedure
Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.

Using "Unlock via Testpoint" function of SmartMoto method
Perform V975 testpoint procedure
Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab

Unlock procedure for V980 phone with testpoint (boot versions starting from 6.36)Downgrade boot method
Perform V980 testpoint procedure
Flash it with C980_boot_5.F.1.smf file
Turn the handset by pressing keys * # PowerON and perform "Remove RSA" procedure
Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.

Using "Unlock via Testpoint" function of SmartMoto method
Perform V980 testpoint procedure
Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab

Unlock procedure for V1050 phone with testpoint (boot versions starting from 6.36)Downgrade boot method
Perform V1050 testpoint procedure
Flash it with V1050_boot_5.F.1.smf file
Turn the handset by pressing keys * # PowerON and perform "Remove RSA" procedure
Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.

Using "Unlock via Testpoint" function of SmartMoto method
Perform V1050 testpoint procedure
Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab

Unlock procedure for C390 phone with testpoint (boot version 8.26)Perform C390 testpoint procedure
Flash it with C390_boot_7.d2.smf file.
Turn the handset on and unlock it with Smart-Clip, simply by pressing UNLOCK button.

Unlock procedure for V360 phone with testpoint (boot versions starting from 8.A0)Using "Unlock via Testpoint" function of SmartMoto method
Perform corresponding testpoint procedure
Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Please note:
We strictly recommend to make a backup of flash from any V360 handset before performing any procedure. If the process fails to complete you will be able to restore your handset to its original state.


Unlock procedure for E1, L6, L7, U6, V190 phone with testpointUsing "Unlock via Testpoint" function of SmartMoto method
Perform corresponding testpoint procedure
Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Please note:
We strictly recommend to make a backup of flash from any E1, L6, L7, U6 or V190 handset before performing any procedure. If the process fails to complete you will be able to restore your handset to its original state.


Unlock procedure for V3i phone with testpoint (boot versions starting from 8.A0)Using "Unlock via Testpoint" function of SmartMoto method
Perform V3i testpoint procedure (Please note: temporarialy you must choose V360 from a list in SmartMoto)
Use "Unlock via Testpoint" function of SmartMoto from "Unlock" tab
Please note:
We strictly recommend to make a backup of flash from any V3i handset before performing any procedure. If the process fails to complete you will be able to restore your handset to its original state.

Smart-Clip upgrade procedureConnect Smart-Clip to PC using ? cable
Power Smart-Clip ? (warning: don't use battery!)
Go to our Upgrade Zone
Upgrade Zone uses ActiveX element, answer "Yes" to install and run it
Press "Connect"

Power Smart-Clip
Disconnect LPT cable

© 2004-2006
support ???????????????? [email protected]
[/B]

[mlmr]

Please remember:
During testpoint unlocking procedure phone's LCD must be disconnected.
Do not use hot air fan to remove a metal shield on PCB. This can seriously damage the handset.
Use any other alternative tool to cut or drill it. Please make sure you do not damage the board.

I've done so..

http:///vbb/showpo...87&postcount=8

[panlem]

there is a safer way than desoldering. Use a sharp stiff blade, have a look at the photo where the TP is. Draw on the tin where it is lining it up using picture http://forum.gsmhosting.com/vbb/show...okr+test+point
the tin is very easy to cut. You can either cut a hole, I leave it as a flap, once done flip it back and put a tape over it. The white water dot is perfect for that.