C100 unlock perfect here ! - GSM-Forum

GSMVN · 09-19-2003, 20:47

Hi mate !

This topic is only for those who has not bought UST .... (Sorry Vahid )

1. First, u flash your C100 with this firmware
C100_1.bin
and C100_2.bin
2. Then, press *2767*2878#
then *2767*637#
3. Insert your simcard and enjoy your phone unlocked !

I've test with about 20 cells .....

Good luck to all mates !

Drug_Store · 09-20-2003, 02:59

Easier Solution:

C100 Unloker Download

1. run program, press "WRITE IMEI"
2. turn on phone
3. connect cable to phone
4. press power off and wait, phone must power off and after that after 1-3 seconds at display you will see 3 fat lines "RED, GREEN, BLUE"
5. in program press "UNLOCK", and you are happy(i think)

THANKS TO ELF

He used a "china box", and I used a Samsung Jig box, so don´t know if works just by simple cable...

Anyway, if u have a box this will work 100%, tested it myself.

GSMVN · 09-20-2003, 05:53

@Drug_Store: I dont use china box. I use direct cable. I must use this way because my C100 WInImeI never run.
It only has com2-com8 port available and I try many ways but It always say Not connect to phone ....

Maybe I've not done right ???

*MaTeOoSh* · 09-20-2003, 07:22

SVC works OK with china "JIG BOX" -tested on some C100 without problems ...

drgsm · 09-20-2003, 09:29

I can't download those flashes, with I111C100_SVC_1.exe i have problems, it always say Fail to Mspersonal value read .. try again, i'm using china box, R210 cable , i don't get those 3 fat lines! what to do?

mobileclinic · 09-20-2003, 13:03

Hi all,
Use A-300 simple unlock cable for svc soft for c100 work 100%.
Key board up
1------------------18
1-5 short
11-gnd
16-rx
17tx
This scheme is tested by me 100%.
Regards.
Mobileclinic

Drug_Store · 09-20-2003, 14:58

Yes, the needed cable is the A300 Unlock.

Drug_Store · 09-20-2003, 15:01

Quote:

Originally posted by Titan_GSM
@Drug_Store: I dont use china box. I use direct cable. I must use this way because my C100 WInImeI never run.
It only has com2-com8 port available and I try many ways but It always say Not connect to phone ....

Maybe I've not done right ???

It has only com2 or com8?.... humm... maybe this is another program, because I use my Jig Box connected to COM1 and works fine, even under XP.

Thanks

GSMVN · 09-20-2003, 16:05

However thanks !!!!!!!

09-19-2003, 20:47	#1 (permalink)
GSMVN Freak Poster Join Date: Aug 2003 Location: www.gsm.com.vn Posts: 394 Member: 36903 Status: Offline Sonork: 64982 Thanks Meter: 2	C100 unlock perfect here ! Hi mate ! This topic is only for those who has not bought UST .... (Sorry Vahid ) 1. First, u flash your C100 with this firmware C100_1.bin and C100_2.bin 2. Then, press 27672878# then 2767637# 3. Insert your simcard and enjoy your phone unlocked ! I've test with about 20 cells ..... Good luck to all mates !

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
V3 Re In Flash Mode Help And V3re Unlock Perfect Not Power On	wiliam	Smart-Clip	5	10-27-2007 08:44
V3x No TP unlock PERFECT!	Invisible	Smart-Clip	13	01-15-2007 11:22
A31 unlock perfect whith dreambox	tobi2	DreamBox	3	04-03-2006 09:15
E350e unlocked perfectly by TST Dongle	Mobile Lab	TST Dongle	8	10-31-2005 09:45
C100 Service manual here for ............	wajid	Samsung Hardware Repair	6	02-19-2005 14:55

09-20-2003, 02:59	#2 (permalink)
Drug_Store No Life Poster Join Date: Sep 2002 Location: Portugal Posts: 8,456 Member: 15312 Status: Offline Sonork: 100.1576041 Thanks Meter: 1,097	Easier Solution: C100 Unloker Download 1. run program, press "WRITE IMEI" 2. turn on phone 3. connect cable to phone 4. press power off and wait, phone must power off and after that after 1-3 seconds at display you will see 3 fat lines "RED, GREEN, BLUE" 5. in program press "UNLOCK", and you are happy(i think) THANKS TO ELF He used a "china box", and I used a Samsung Jig box, so don´t know if works just by simple cable... Anyway, if u have a box this will work 100%, tested it myself.

09-20-2003, 05:53	#3 (permalink)
GSMVN Freak Poster Join Date: Aug 2003 Location: www.gsm.com.vn Posts: 394 Member: 36903 Status: Offline Sonork: 64982 Thanks Meter: 2	@Drug_Store: I dont use china box. I use direct cable. I must use this way because my C100 WInImeI never run. It only has com2-com8 port available and I try many ways but It always say Not connect to phone .... Maybe I've not done right ???

09-20-2003, 07:22	#4 (permalink)
MaTeOoSh No Life Poster Join Date: Dec 2000 Location: gsmdoctor.pl Age: 48 Posts: 1,317 Member: 2755 Status: Offline Thanks Meter: 42	SVC works OK with china "JIG BOX" -tested on some C100 without problems ...

09-20-2003, 09:29	#5 (permalink)
drgsm Junior Member Join Date: Feb 2003 Posts: 35 Member: 23382 Status: Offline Thanks Meter: 0	I can't download those flashes, with I111C100_SVC_1.exe i have problems, it always say Fail to Mspersonal value read .. try again, i'm using china box, R210 cable , i don't get those 3 fat lines! what to do?

09-20-2003, 13:03	#6 (permalink)
mobileclinic Product Supporter Join Date: Sep 2001 Location: India Posts: 1,331 Member: 6109 Status: Offline Sonork: 100.37432 Thanks Meter: 3,781	Hi all, Use A-300 simple unlock cable for svc soft for c100 work 100%. Key board up 1------------------18 1-5 short 11-gnd 16-rx 17tx This scheme is tested by me 100%. Regards. Mobileclinic

09-20-2003, 14:58	#7 (permalink)
Drug_Store No Life Poster Join Date: Sep 2002 Location: Portugal Posts: 8,456 Member: 15312 Status: Offline Sonork: 100.1576041 Thanks Meter: 1,097	Yes, the needed cable is the A300 Unlock.

09-20-2003, 16:05	#9 (permalink)
GSMVN Freak Poster Join Date: Aug 2003 Location: www.gsm.com.vn Posts: 394 Member: 36903 Status: Offline Sonork: 64982 Thanks Meter: 2	However thanks !!!!!!!