V200 Flashing problem, phone dead! - GSM-Forum

rango · 05-05-2003, 17:28

I have tried to flash V200 with OptiFlash 3.5.0.2...
I found instructions on the net for configuring OptiFlash for flashing, and I did all like it said...

But my phone is dead now!!!

((((((((

Here is the program log:

E89 6:18:44 PM ThreadGUI started
I E90 6:18:44 PM ThreadProtocol started
I E91 6:18:44 PM Boot loader protocol type: passive
I E92 6:18:44 PM Flash loader: C:\GSM\SAMSUNG\OPTIFLASH_3.5.0.2\sceptre3_sgh_hw4_ v200.sre
I E93 6:18:44 PM Opened COM1 at 115200 baud
I E94 6:18:45 PM PC transfer speeds (COM1): 57600 115200
I E95 6:18:45 PM Loading S-record file: <C:\GSM\SAMSUNG\OPTIFLASH_3.5.0.2\sceptre3_sgh_hw4 _v200.sre>, RangeCheck=Off
I E96 6:18:48 PM There is 1 memory region in the S-record file:
I E97 6:18:48 PM 1: 0x00000000 - 0x00004a4b = 19020 Bytes
I E98 6:18:48 PM Loading S-record file: <C:\Downloads\Samsung\flash\v200\V20AIWB2_WC3.s3 >, RangeCheck=On
I E99 6:18:49 PM There are 4 memory regions in the S-record file:
I E100 6:18:49 PM 1: 0x00000000 - 0x00000617 = 1560 Bytes
I E101 6:18:49 PM 2: 0x00004000 - 0x00007a43 = 14916 Bytes
I E102 6:18:49 PM 3: 0x00010000 - 0x00567957 = 5601624 Bytes
I E103 6:18:49 PM 4: 0x00700000 - 0x00cbd67f = 6018688 Bytes
I E104 6:18:49 PM SendFile=C:\GSM\SAMSUNG\OPTIFLASH_3.5.0.2\sceptre3 _sgh_hw4_v200.sre, Mode=3
I E105 6:18:49 PM Power on mobile !
I E106 6:18:49 PM TalkToBootloader (using COM1)
I E107 6:18:49 PM Talking to passive bootloader
I E108 6:18:49 PM Bootloader V2.1 using UART1
I E109 6:18:49 PM ROM mask ID: 0x00004542 ( EB)
I E110 6:18:49 PM ID register: 0x000203b9 (Trident II)
I E111 6:18:49 PM Bootloader type: 3
I E112 6:18:49 PM Max. transfer size: 2176 bytes
I E113 6:18:49 PM Send: 0x00000000 - 0x000007ff (=2048)
I E114 6:18:50 PM Send: 0x00000800 - 0x00000fff (=2048)
I E115 6:18:50 PM Send: 0x00001000 - 0x000017ff (=2048)
I E116 6:18:50 PM Send: 0x00001800 - 0x00001fff (=2048)
I E117 6:18:50 PM Send: 0x00002000 - 0x000027ff (=2048)
I E118 6:18:50 PM Send: 0x00002800 - 0x00002fff (=2048)
I E119 6:18:51 PM Send: 0x00003000 - 0x000037ff (=2048)
I E120 6:18:51 PM Send: 0x00003800 - 0x00003fff (=2048)
I E121 6:18:51 PM Send: 0x00004000 - 0x000047ff (=2048)
I E122 6:18:51 PM Send: 0x00004800 - 0x00004a4b (=588)
I E123 6:18:51 PM TalkToBootloader: OK
I E124 6:18:51 PM Duration: 1s
I E125 6:18:51 PM SendFile=C:\Downloads\Samsung\flash\v200\V20AIWB2_ WC3.s3, Mode=0
I E126 6:18:51 PM TalkToFlashloader (using COM1)
I E127 6:18:51 PM Switching over to flash loader
I E128 6:18:51 PM COM1 is connected to UART1
I E129 6:18:51 PM Sync'ing to flash loader
I E130 6:18:51 PM Querying device information
I E131 6:18:51 PM Flash loader version: V4.13
I E132 6:18:51 PM Max. TX/RX size: 65536/32768
I E133 6:18:51 PM Mobile transfer speeds: 57600, 115200, 230400, 460800
I E134 6:18:51 PM Detected flash chips: 2
I E135 6:18:51 PM 1: Manufacturer: 0xb0, Device: 0x00b1
I E136 6:18:51 PM 2: Manufacturer: 0xb0, Device: 0x00b0
I E137 6:18:51 PM 0xb0/0x00b1: Sharp LRS1393 (or LRS1395 first bank) (8 MB (8388608 Bytes) in 135 sectors)
I E138 6:18:51 PM 0xb0/0x00b0: Sharp LRS1395 (second bank) (8 MB (8388608 Bytes) in 135 sectors)
I E139 6:18:51 PM Total flash size: 16 MB (16777216 Bytes) in 270 sectors
I E140 6:18:51 PM Port info:
I E141 6:18:51 PM Logical port 0: COM1 <-> UART1 at 115200 baud (~100%)
I E142 6:18:51 PM TalkToFlashloader: OK
I E143 6:18:51 PM There are 3 reserved regions defined:
I E144 6:18:51 PM 1: 0x00002000 - 0x00003fff = 8192 Bytes
I E145 6:18:51 PM 2: 0x00008000 - 0x0000dfff = 24576 Bytes
I E146 6:18:51 PM 3: 0x00ea0000 - 0x00feffff = 1376256 Bytes
I E147 6:18:51 PM Data to be transferred: 11 MB (11636788 Bytes)
I E148 6:18:51 PM Setup
I E149 6:18:51 PM Sector: 0
I E150 6:18:51 PM VerifyData: 0x00000000 - 0x00000617
I E151 6:18:51 PM VerifyData: Detected difference (0x625f1ada != 0x8833948e)
I E152 6:18:51 PM OpenSector: 0, 0x00000000, 8192, 0x13
I E153 6:18:51 PM SendData: 0x00000000 - 0x00000617
I E154 6:19:01 PM Cmd TXDT FAILED: Err:3, 0=0x0, 1560=0x618, 0=0x0, 0=0x0
I E155 6:19:01 PM Retry 1: SendData
I E156 6:19:01 PM SendData: 0x00000000 - 0x00000617
I E157 6:19:10 PM Cmd TXDT FAILED: Err:3, 0=0x0, 1560=0x618, 0=0x0, 0=0x0
I E158 6:19:10 PM Retry 2: SendData
I E159 6:19:10 PM SendData: 0x00000000 - 0x00000617
I E160 6:19:20 PM Cmd TXDT FAILED: Err:3, 0=0x0, 1560=0x618, 0=0x0, 0=0x0
I E161 6:19:20 PM Retry 3: SendData
I E162 6:19:20 PM SendData: 0x00000000 - 0x00000617
I E163 6:19:29 PM Cmd TXDT FAILED: Err:3, 0=0x0, 1560=0x618, 0=0x0, 0=0x0
I E164 6:19:29 PM Retry 4: SendData
I E165 6:19:29 PM SendData: 0x00000000 - 0x00000617
I E166 6:19:39 PM Cmd TXDT FAILED: Err:3, 0=0x0, 1560=0x618, 0=0x0, 0=0x0
I E167 6:19:39 PM Giving up on SendData
I E168 6:19:39 PM SendFile: 14 (ERR_TOO_MANY_RETRIES)
I E169 6:19:39 PM ReLoad: 14 (ERR_TOO_MANY_RETRIES)
I E170 6:19:39 PM Error code: ERR_TOO_MANY_RETRIES
E E171 6:19:39 PM Sorry, an error has occured ! (ERR_TOO_MANY_RETRIES)
I E172 6:19:39 PM ThreadProtocol finished
I E173 6:19:39 PM ThreadProtocol: 14
I E174 6:19:39 PM ThreadGUI finished

I'ts confort for me that phone still boots. but dont wont to continue flashing...

If anyone have solution for my problem please reply...

Thanx

VsH-GsM · 05-05-2003, 18:03

soon ill upload software+flasher for v20x to my site ,,, it will repair your phone

adv · 05-05-2003, 19:11

Just use windows 2000 or Xp and your phone will be ok.

regards

rango · 05-05-2003, 19:18

Great VSH, I look forward to it...

We are the one of that guys who have the guts to try it first, but without that how woud we know what software works or not, and how to do it...

I have one more question VSH, do you know or have A800,S100,S300,V200 flash with Croatian (Hrvatski) language, I can't find it on the net...

Thanx

VSH rules!

yousha · 05-05-2003, 19:40

i agree VSH softwares really works.......100%

rango · 05-05-2003, 22:24

Adv was right, Optiflash work ok only in win2000 or XP...

I sucesfully flashed my phone from Windows XP and now it workes!!!

)))))))))))))))))))))))))))))

Adv I can't thank you enough for this hint...

Thanx again

If anybody have A800,S100,S300 or V200 flash with Croatian (Hrvatski) language please share with me and rest of us...

my e-mail:
[email protected]

Assamiea · 05-05-2003, 23:27

V20XEWC2 flash file (V200) with Croatian (Hrvatski) language.
http://www.mobilz.org/free/Samsung/V20x/v20x.rar

mobileland · 05-06-2003, 01:55

What about a800 with croatian?

rango · 05-06-2003, 03:27

Assamiea Thanx for the link...

I still need flash for a800,s100 and s300, if anybody have please share...

anhtam · 05-06-2003, 05:15

anyone try to flash V205 with V200 flash file?

vuanh_nd · 05-06-2003, 10:04

Hi Anh Tam ! you have flash V200 language vietnamese ? I need it, pls reply to me.

say2k · 05-06-2003, 10:47

I flashed v200 to v200c but camera don't work after flash, reflash with v200c flash file problen is the same. Anyone have idea?

adv · 05-06-2003, 11:00

What flash did you used?

regards

say2k · 05-06-2003, 11:03

v20aiwb2 and V20XEWC2.s3 all the same

Assamiea · 05-06-2003, 12:03

I still need flash for a800,s100 and s300, if anybody have please share...
I don't have those phones, what flash file codes?

anyone try to flash V205 with V200 flash file?
I flashed it and use for 3 weeks with no problem at all, even the camera.

Here step by step Upgrade V205 to V200.

OptiFlash (V20X) with flash file v20xewc2.s3, Unzip those all to one folder. (Windows XP Only)

Use Cable: V205/V200 (#PCB037DBE), R225, T100 and S300.

Added Features:
1. Hide Operation Logo, time and date.
2. Camera zoom.
3. Upload the cam pictures to PC.
4. Activate Folder Tone (same as S300).
5. More keypad tones (Cool & Piano).
6. New startup screen. (T-Mobile is gone)
7. More wallpapers.
8. Animation when searching service is different.
9. Restricted: Call Barring, Closed User Group.
10. MMS and WAP settings with out entering the code.
And more.........

************************************************** ************************************************** ****
How to BACKUP ...........

1) Open OptiFlash program go to Options\Settings\COM Port, set First COM Port only, disabled Second COM Port (none) .

2) Click READ tab deleted all the existing read ranges and add the following up ranges:

0x00000000 - 0x00000617
0x00004000 - 0x00007a43
0x00010000 - 0x00576a53
0x00700000 - 0x00cbd713

Then click on ok.

3) Take out the sim card, connect cable to phone and then click on READ...software will then ask to power on mobile, Press the pwr button on phone for about 1-2 seconds ( You will NOT see the phone come on!! ).

This will take about 10 or so mins to read the flash..file output is 34 mb. It will say "all is well" when its finished reading. remove battery and put it back on.

4) Now goto options settings FLASH & VERIFY tab then open the file that you just saved which is the flash of your own fone. Click ok and then click on VERIFY. If it verifies 100% it will say all is well. remove battery put it back on.
IMPORTANT NOTE IF YOU GET ANY ERROR HERE DURING THE VERIFY PROCESS I HIGHLY RECOMMEND THAT YOU NOT CONTINUE.

How to FLASH:
1) Goto options\settings\flash and verify, open the new v200 flash file its called v20xewc2.s3.

2) Clear Reserved memory regions (blank, no need to type in any range) .

3) Click on Generic tab, select Customer T1, v200 in specify hardware platform. Then press ok.

4) Click on FLASH buttom start to flash. software will then ask to power on mobile, Press the pwr button on phone for about 1-2 seconds ( You will NOT see the phone come on!! ). This process took about 20mins then it said all is well. At this point it was done.

5) Remove cable and battery, then put the battery back on then turned on the phone (without sim card).

9) When phone ask you to insert sim do this resets (each one will reboots then insert next code)

*2767*MEDIA#
*2767*FULL#
*2767*CUST#
*2767*WAP#
*2767*STACKRESET#
(After the phone reboots "Personalization Cancelled" should be displayed.)

10) SMILE ;-) It's done! Turn off the phone, insert sim card.

GOOD LUCK!!!

05-05-2003, 23:27	#7 (permalink)
Assamiea Freak Poster Join Date: Jul 2002 Location: CAN Posts: 159 Member: 13761 Status: Offline Thanks Meter: 0	If anybody have A800,S100,S300 or V200 flash with Croatian (Hrvatski) language please V20XEWC2 flash file (V200) with Croatian (Hrvatski) language. http://www.mobilz.org/free/Samsung/V20x/v20x.rar

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Flash V208 to my V200, then the phone dead..	Speedy	UFS2 + UFS3-Tornadoflasher	6	12-16-2014 01:13
Problem Flashing 6120c, phone dead	juliog	MT-BOX	4	02-17-2009 16:17
V200 Flashing problem HELP!!!!!	AlexG	Trident/AGERE Platform	3	10-03-2003 09:15
V200 Flashing Problem-need help urgent.	dominik	Trident/AGERE Platform	2	07-19-2003 18:13

05-05-2003, 18:03	#2 (permalink)
VsH-GsM Banned Join Date: Nov 2001 Location: IRAN Age: 38 Posts: 3,679 Member: 7444 Status: Offline Sonork: 100.99999 Thanks Meter: 10,013	soon ill upload software+flasher for v20x to my site ,,, it will repair your phone

05-05-2003, 19:11	#3 (permalink)
adv Freak Poster Join Date: Sep 2002 Location: somewhere... Posts: 419 Member: 15165 Status: Offline Thanks Meter: 0	Just use windows 2000 or Xp and your phone will be ok. regards

05-05-2003, 19:18	#4 (permalink)
rango Freak Poster Join Date: Dec 2000 Location: Belgrade, Serbia Age: 44 Posts: 238 Member: 2768 Status: Offline Thanks Meter: 12	Great VSH, I look forward to it... We are the one of that guys who have the guts to try it first, but without that how woud we know what software works or not, and how to do it... I have one more question VSH, do you know or have A800,S100,S300,V200 flash with Croatian (Hrvatski) language, I can't find it on the net... Thanx VSH rules!

05-05-2003, 19:40	#5 (permalink)
yousha No Life Poster Join Date: Nov 2002 Age: 43 Posts: 1,503 Member: 17689 Status: Offline Sonork: 100.72392 Thanks Meter: 737	i agree VSH softwares really works.......100%

05-05-2003, 22:24	#6 (permalink)
rango Freak Poster Join Date: Dec 2000 Location: Belgrade, Serbia Age: 44 Posts: 238 Member: 2768 Status: Offline Thanks Meter: 12	Adv was right, Optiflash work ok only in win2000 or XP... I sucesfully flashed my phone from Windows XP and now it workes!!! ))))))))))))))))))))))))))))) Adv I can't thank you enough for this hint... Thanx again If anybody have A800,S100,S300 or V200 flash with Croatian (Hrvatski) language please share with me and rest of us... my e-mail: [email protected]

05-06-2003, 01:55	#8 (permalink)
mobileland No Life Poster Join Date: Feb 2003 Location: www.X-SIM.me Age: 45 Posts: 2,424 Member: 22955 Status: Offline Sonork: 67574 - Not use it Thanks Meter: 584	What about a800 with croatian?

05-06-2003, 03:27	#9 (permalink)
rango Freak Poster Join Date: Dec 2000 Location: Belgrade, Serbia Age: 44 Posts: 238 Member: 2768 Status: Offline Thanks Meter: 12	Assamiea Thanx for the link... I still need flash for a800,s100 and s300, if anybody have please share...

05-06-2003, 05:15	#10 (permalink)
anhtam No Life Poster Join Date: Dec 2001 Age: 56 Posts: 1,146 Member: 7721 Status: Offline Sonork: 100.1598522 Thanks Meter: 23	anyone try to flash V205 with V200 flash file?

05-06-2003, 10:04	#11 (permalink)
vuanh_nd Freak Poster Join Date: Apr 2003 Location: Viet Nam Age: 57 Posts: 140 Member: 27519 Status: Offline Thanks Meter: 0	Hi Anh Tam ! you have flash V200 language vietnamese ? I need it, pls reply to me.

05-06-2003, 10:47	#12 (permalink)
say2k Freak Poster Join Date: Oct 2001 Location: Viet Nam Age: 46 Posts: 230 Member: 6881 Status: Offline Thanks Meter: 0	I flashed v200 to v200c but camera don't work after flash, reflash with v200c flash file problen is the same. Anyone have idea?

05-06-2003, 11:00	#13 (permalink)
adv Freak Poster Join Date: Sep 2002 Location: somewhere... Posts: 419 Member: 15165 Status: Offline Thanks Meter: 0	What flash did you used? regards

05-06-2003, 11:03	#14 (permalink)
say2k Freak Poster Join Date: Oct 2001 Location: Viet Nam Age: 46 Posts: 230 Member: 6881 Status: Offline Thanks Meter: 0	v20aiwb2 and V20XEWC2.s3 all the same

05-06-2003, 12:03	#15 (permalink)
Assamiea Freak Poster Join Date: Jul 2002 Location: CAN Posts: 159 Member: 13761 Status: Offline Thanks Meter: 0	I still need flash for a800,s100 and s300, if anybody have please share... I don't have those phones, what flash file codes? anyone try to flash V205 with V200 flash file? I flashed it and use for 3 weeks with no problem at all, even the camera. Here step by step Upgrade V205 to V200. OptiFlash (V20X) with flash file v20xewc2.s3, Unzip those all to one folder. (Windows XP Only) Use Cable: V205/V200 (#PCB037DBE), R225, T100 and S300. Added Features: 1. Hide Operation Logo, time and date. 2. Camera zoom. 3. Upload the cam pictures to PC. 4. Activate Folder Tone (same as S300). 5. More keypad tones (Cool & Piano). 6. New startup screen. (T-Mobile is gone) 7. More wallpapers. 8. Animation when searching service is different. 9. Restricted: Call Barring, Closed User Group. 10. MMS and WAP settings with out entering the code. And more......... ************************************************ ********************************************** ** How to BACKUP ........... 1) Open OptiFlash program go to Options\Settings\COM Port, set First COM Port only, disabled Second COM Port (none) . 2) Click READ tab deleted all the existing read ranges and add the following up ranges: 0x00000000 - 0x00000617 0x00004000 - 0x00007a43 0x00010000 - 0x00576a53 0x00700000 - 0x00cbd713 Then click on ok. 3) Take out the sim card, connect cable to phone and then click on READ...software will then ask to power on mobile, Press the pwr button on phone for about 1-2 seconds ( You will NOT see the phone come on!! ). This will take about 10 or so mins to read the flash..file output is 34 mb. It will say "all is well" when its finished reading. remove battery and put it back on. 4) Now goto options settings FLASH & VERIFY tab then open the file that you just saved which is the flash of your own fone. Click ok and then click on VERIFY. If it verifies 100% it will say all is well. remove battery put it back on. IMPORTANT NOTE IF YOU GET ANY ERROR HERE DURING THE VERIFY PROCESS I HIGHLY RECOMMEND THAT YOU NOT CONTINUE. How to FLASH: 1) Goto options\settings\flash and verify, open the new v200 flash file its called v20xewc2.s3. 2) Clear Reserved memory regions (blank, no need to type in any range) . 3) Click on Generic tab, select Customer T1, v200 in specify hardware platform. Then press ok. 4) Click on FLASH buttom start to flash. software will then ask to power on mobile, Press the pwr button on phone for about 1-2 seconds ( You will NOT see the phone come on!! ). This process took about 20mins then it said all is well. At this point it was done. 5) Remove cable and battery, then put the battery back on then turned on the phone (without sim card). 9) When phone ask you to insert sim do this resets (each one will reboots then insert next code) 2767MEDIA# 2767FULL# 2767CUST# 2767WAP# 2767STACKRESET# (After the phone reboots "Personalization Cancelled" should be displayed.) 10) SMILE ;-) It's done! Turn off the phone, insert sim card. GOOD LUCK!!!