100% bullet proof E1 Itunes unlock instruction

[MONO]

Hello all with problems with unlocking E1 Itunes with Smart-clip 2.21 firmware.

* 1 Picture Motorola_E1_TP_-001.jpg
This only show that you have to disassemble the phone


* 2 Picture Motorola_E1_TP_-002.jpg
After that you have disassemble the phone phone take off the camera then you can start taking off the metal plate. I used a Soldering Iron to release the edges. Then you can just bend och cut. Just take it easy so you don´t damage the components under the metal plate.


* 3 Picture Motorola_E1_TP_-003.jpg
Now when the plate is off it´s time to connect us to the GND. I´m using the "left overs" from the metal plate to hook on. In the other end of the cable I have the TP TOOL that I place on the TP that Smart-clip illustrate on ther site.


* 4 Picture Motorola_E1_TP_-004.jpg
Now when we have connected us to the GND it´s time to place the battery and make some room/space so that we can connect the TP TOOL to the correct spot. I´m using rubberband to hold the battery in place.


Now over to the instruction.

INSTRUCTION.
Then phone should now look like picture 4 Motorola_E1_TP_-004.jpg and NO TP connected yet.

1. Make sure you have a fully loaded battery.
2. Rather use power adaptor for your clip and not 9v.
3. Put power to the clip.
4. Connect USB cable to the phone.
5. Start phone (you should be able to push the start button and let the rubberband hold your phone)
6. Wait until phone is fully started.
7. Start SmartMoto 1.12 (I´m sure you can start this when ever you want).
8. Open Smart-clip Tab/section and press connect.

Now you should see somthing like this:
Clip serial: 2124xxxxx, version: 2.21, initializing... OK

9. Press search button. (NO TP YET!! )

Now you should see somthing like this:
Searching for phone... found Motorola Phone (E1 iTunes iTunes), getting test interface... OK
Model E1 iTunes
Firmware R373_G_0E.30.42R
Reading info OK

10. Now it´s time to prepare for TP. Before you press SEARCH AGAIN connect TP and directly after TP press search button. When the sofware finds the phone take OFF TP.
Now you should see something like this:
Searching for phone... found S Blank Neptune LTE, getting test interface... interface not found
Switching to flash mode... OK

NO MORE TP NEEDED!!!

11. Now I´m makeing backup for the language in the phone. Go to flash tab/section and press Read language.

Reading phone boot version... 2.00
Reading flash id... Intel-28F256L18B
Phone group: A630,E1,E37x,E39x,E55x,V3,V190,V330,V53x,V54x,V55x ,V62x,V635,V80
Hardware IMEI: 35687xxxxxxxxxx
Security area saved to "S Blank Neptune LTE 35687xxxxxxxxx.pds"
Resolving section "language" location... OK
Reading language pack done

Now we have saved that in case something should go wrong when we unlock the phone.

12. Now I´m makeing backup for the Phone flash. Go to backup tab/section and press Backup phone flash.

Now you should see somthing like this:
"S Blank Neptune LTE 35687xxxxxxxxx.smb" saved, 32 Mb

and it takes some time before this is done.


Now it´s time to unlock the phone. Goto Unlock tab/section and press Unlock via testpoint.

NO TP NEEDED!

Now you should see somthing like this:
Writing section0 done
Turning phone off... OK
Searching for phone... found S Blank Neptune LTE
Switching to flash mode... OK
Unlocking phone... OK

Easy as that, and your phone is unlocked :-).
/Mike

[SM4RTBOY]

Originally Posted by MONO

Hello all with problems with unlocking E1 Itunes with Smart-clip 2.21 firmware.
* 1 Picture Motorola_E1_TP_-001.jpg
This only show that you have to disassemble the phone
* 2 Picture Motorola_E1_TP_-002.jpg
After that you have disassemble the phone phone take off the camera then you can start taking off the metal plate. I used a Soldering Iron to release the edges. Then you can just bend och cut. Just take it easy so you don´t damage the components under the metal plate.
* 3 Picture Motorola_E1_TP_-003.jpg
Now when the plate is off it´s time to connect us to the GND. I´m using the "left overs" from the metal plate to hook on. In the other end of the cable I have the TP TOOL that I place on the TP that Smart-clip illustrate on ther site.
* 4 Picture Motorola_E1_TP_-004.jpg
Now when we have connected us to the GND it´s time to place the battery and make some room/space so that we can connect the TP TOOL to the correct spot. I´m using rubberband to hold the battery in place.
Now over to the instruction.
INSTRUCTION.
Then phone should now look like picture 4 Motorola_E1_TP_-004.jpg and NO TP connected yet.
1. Make sure you have a fully loaded battery.
2. Rather use power adaptor for your clip and not 9v.
3. Put power to the clip.
4. Connect USB cable to the phone.
5. Start phone (you should be able to push the start button and let the rubberband hold your phone)
6. Wait until phone is fully started.
7. Start SmartMoto 1.12 (I´m sure you can start this when ever you want).
8. Open Smart-clip Tab/section and press connect.
Now you should see somthing like this:
Clip serial: 2124xxxxx, version: 2.21, initializing... OK
9. Press search button. (NO TP YET!! )
Now you should see somthing like this:
Searching for phone... found Motorola Phone (E1 iTunes iTunes), getting test interface... OK
Model E1 iTunes
Firmware R373_G_0E.30.42R
Reading info OK
10. Now it´s time to prepare for TP. Before you press SEARCH AGAIN connect TP and directly after TP press search button. When the sofware finds the phone take OFF TP.
Now you should see something like this:
Searching for phone... found S Blank Neptune LTE, getting test interface... interface not found
Switching to flash mode... OK
NO MORE TP NEEDED!!!
11. Now I´m makeing backup for the language in the phone. Go to flash tab/section and press Read language.
Reading phone boot version... 2.00
Reading flash id... Intel-28F256L18B
Phone group: A630,E1,E37x,E39x,E55x,V3,V190,V330,V53x,V54x,V55x ,V62x,V635,V80
Hardware IMEI: 35687xxxxxxxxxx
Security area saved to "S Blank Neptune LTE 35687xxxxxxxxx.pds"
Resolving section "language" location... OK
Reading language pack done
Now we have saved that in case something should go wrong when we unlock the phone.
12. Now I´m makeing backup for the Phone flash. Go to backup tab/section and press Backup phone flash.
Now you should see somthing like this:
"S Blank Neptune LTE 35687xxxxxxxxx.smb" saved, 32 Mb
and it takes some time before this is done.
Now it´s time to unlock the phone. Goto Unlock tab/section and press Unlock via testpoint.
NO TP NEEDED!
Now you should see somthing like this:
Writing section0 done
Turning phone off... OK
Searching for phone... found S Blank Neptune LTE
Switching to flash mode... OK
Unlocking phone... OK
Easy as that, and your phone is unlocked :-).
/Mike

...so TP or NOT ! are you drunked ? hahahhahahahhaha
old news.....you nedd practice and press search button !

enjoy

sm4rtboy

[MONO]

Yes I know this is old news but questions are still asked in the forum and hopefully this information can help somebody. More than your instruction

"
THE SECRET IS : phone ON , battery attached..than ~make TP and ..unlock via smartmoto at same time !..
after that unlock again (here) no TP required at end session ..
"

[simlockgsm]

Great info Sm4rtboy!
Now if only I could get my customers to accept ripping their phone appart and voiding their warranty...lol
yes, that sarcasm...