e1000 dead after successful unlock - GSM-Forum

Burnt Cobba · 11-16-2006, 06:48

hi mates.

just tried to unlock this one up using test point. after shown unlock.. ok the set is dead.

my first experience with an E1000. (not so good)

anyone can help in this pls?

thanks

Mr.Tinkertrain · 11-16-2006, 09:46

@ Burnt Cobba,

Try to make Repair PDS and after that Full Flash the phone.

Best Regards
Smart-clip team
www.smart-clip.com
www.GsmServer.com
www.boot-loader.com
www.smart-unlocker.com

Burnt Cobba · 11-16-2006, 19:12

giving a look at the motherboard i think while i was cutting the shielding the small coil that is on the left hand side got slightly damaged. maybe that is why it is not powering. Infact not even via test point it is not communicating at all. That leaves out software problem.

Any expert on motos pls? thanks for the help.

Lhick · 11-21-2006, 12:16

I hope look at its Bootloader, There is 6.31 ver. you just remove RSA no TP mate

Burnt Cobba · 11-21-2006, 15:49

problem is that it wont communicate with smart clip

11-16-2006, 06:48	#1 (permalink)
Burnt Cobba No Life Poster Join Date: Apr 2002 Location: The Green Mile Posts: 3,653 Member: 11325 Status: Offline Thanks Meter: 266	e1000 dead after successful unlock hi mates. just tried to unlock this one up using test point. after shown unlock.. ok the set is dead. my first experience with an E1000. (not so good) anyone can help in this pls? thanks

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
S5233S Dead After Successfully Flashing..	LoveLess	SPT BOX	7	11-29-2009 12:18
post here all LG phones which ( DEAD ) after successfully Unlocked	Mounir	ULT PRO	14	05-04-2008 23:15
E1000 dead ERR: POG UNLOCK 004 Got_moto	dacelectronic	Motorola P2k	0	12-18-2006 20:03
My Smart Clip is dead after successful update.	kkkhel	Smart-Clip	3	01-30-2006 16:26

11-16-2006, 09:46	#2 (permalink)
Mr.Tinkertrain No Life Poster Join Date: Feb 2006 Posts: 11,638 Member: 229997 Status: Offline Thanks Meter: 636	@ Burnt Cobba, Try to make Repair PDS and after that Full Flash the phone. Best Regards Smart-clip team www.smart-clip.com www.GsmServer.com www.boot-loader.com www.smart-unlocker.com

11-16-2006, 19:12	#3 (permalink)
Burnt Cobba No Life Poster Join Date: Apr 2002 Location: The Green Mile Posts: 3,653 Member: 11325 Status: Offline Thanks Meter: 266	giving a look at the motherboard i think while i was cutting the shielding the small coil that is on the left hand side got slightly damaged. maybe that is why it is not powering. Infact not even via test point it is not communicating at all. That leaves out software problem. Any expert on motos pls? thanks for the help.

11-21-2006, 12:16	#4 (permalink)
Lhick No Life Poster Join Date: Aug 2006 Location: InsideOut Posts: 5,657 Member: 333359 Status: Offline Thanks Meter: 91	I hope look at its Bootloader, There is 6.31 ver. you just remove RSA no TP mate

11-21-2006, 15:49	#5 (permalink)
Burnt Cobba No Life Poster Join Date: Apr 2002 Location: The Green Mile Posts: 3,653 Member: 11325 Status: Offline Thanks Meter: 266	problem is that it wont communicate with smart clip