alcatel 9026x by tcl need firmware just show bule display
 

Using library Brom_DLL_v7.1813.3
Engine version 1.0.0.5188
Searching phone in normal mode;
[connect the phone powered off to the usb cable]
Phone detected (MediaTek USB Port_V1632 (COM17)) (Driver version: 3.0.1504.0)
Preparing to start flash mode;
Preparing to open COM17
Requesting authorization;
Connecting;
Downloading DA;
Initializing;
Rid: 261b95f92611a0deba5a2a012dbc2b2c
Requesting baudrate change;
Done;
USB SPEED: USB_FULL_SPEED
Switching to DA_HIGHSPEED_VCOM;

Drivers location \usb_driver\Driver_Auto_Installer\SmartPhoneDriver \;
If the detection fails, install manually the port from the device manager using usbvcom.inf;

DA_HIGHSPEED_VCOM (@oem44.inf,%vcom_da%;MediaTek DA USB VCOM (Android))
TRYING TO OPEN COM69;
DEVICE INFO:
BB CHIP: MT6737M [CA00, 00, 335, 05]
HW_STORAGE_EMMC: 0x44000145 0x31303446 0xCAB30136 0xC7C393E8 [SIZE=0x3AC000000]
IMEI1 [OTP 0000]: 35?????????????????
IMEI2 [OTP 0000]: 000000-00-000000-0
PROVIDER: 9026X-2EALAV1
USRDATA INFO: 0xEB000000 SIZE: 0x2BC880000


Getting partitions info;
Reading info;
Partitions info:
[0x00080000-0x00300000]-[proinfo]
[0x00380000-0x00500000]-[nvram]
[0x00880000-0x00A00000]-[protect1]
[0x01280000-0x00A00000]-[protect2]
[0x01C80000-0x01900000]-[persist]
[0x03580000-0x00080000]-[lk]
[0x03600000-0x00080000]-[para]
[0x03680000-0x01000000]-[boot]
[0x04680000-0x01000000]-[recovery]
[0x05680000-0x00800000]-[logo]
[0x05E80000-0x00A00000]-[expdb]
[0x06880000-0x00080000]-[seccfg]
[0x06900000-0x00200000]-[oemkeystore]
[0x06B00000-0x00600000]-[secro]
[0x07100000-0x00800000]-[keystore]
[0x07900000-0x00500000]-[tee1]
[0x07E00000-0x00500000]-[tee2]
[0x08300000-0x00080000]-[efuse]
[0x08380000-0x00100000]-[frp]
[0x08480000-0x02000000]-[nvdata]
[0x0A480000-0x02000000]-[metadata]
[0x0C480000-0x00800000]-[simlock]
[0x0CC80000-0x04000000]-[oemisc]
[0x10C80000-0x01380000]-[mobile_info]
[0x12000000-0xC0000000]-[system]
[0xD2000000-0x19000000]-[cache]
[0xEB000000-0x2BC880000]-[userdata]
[0x3A7880000-0x02B00000]-[otp]
[0x3AA380000-0x01000000]-[flashinfo]




download this firmware

9026X-2[X=A]VVBG1_4G2NCVN2.osp ?????
its ok

Yes. Can write any 9026 firmware


Br;)

Using library Brom_DLL_v7.1813.3
Engine version 1.0.0.5188
Searching phone in normal mode;
[connect the phone powered off to the usb cable]
Phone detected (MediaTek USB Port_V1632 (COM17)) (Driver version: 3.0.1504.0)
Preparing to start flash mode;
Preparing to open COM17
Requesting authorization;
Connecting;
Downloading DA;
Initializing;
Rid: 261b95f92611a0deba5a2a012dbc2b2c
Requesting baudrate change;
Done;
USB SPEED: USB_FULL_SPEED
Switching to DA_HIGHSPEED_VCOM;

Drivers location \usb_driver\Driver_Auto_Installer\SmartPhoneDriver \;
If the detection fails, install manually the port from the device manager using usbvcom.inf;

DA_HIGHSPEED_VCOM (@oem44.inf,%vcom_da%;MediaTek DA USB VCOM (Android))
TRYING TO OPEN COM69;
DEVICE INFO:
BB CHIP: MT6737M [CA00, 00, 335, 05]
HW_STORAGE_EMMC: 0x44000145 0x31303446 0xCAB30136 0xC7C393E8 [SIZE=0x3AC000000]
IMEI1 [OTP 0000]: 356801-08-003225-4
IMEI2 [OTP 0000]: 000000-00-000000-0
PROVIDER: 9026X-2EALAV1
USRDATA INFO: 0xEB000000 SIZE: 0x2BC880000


Loading the file ...
Cfg done ...
Formatting file system now...
Done;
Formatting PROTECT1 partition now...
Done;
Formatting PROTECT2 partition now...
Done;
Formatting SECCFG partition now...
Done;
Formatting FRP partition now...
Done;
Formatting NVDATA partition now...
Done;
Formatting METADATA partition now...
Done;
Downloading bootloader...
Done;
Downloading images...
Done;
Success;

Time needed - 00:06:21

Log file saved to: LOG_11_07_2021_06_08_00.txt


after flash still same bule display

Then the display is bad. I will upload you later the same provider id but im sure the fault is within the display

Br:)


Sent from my iPhone using Tapatalk Pro