wiko jenny spectrum sc7731c full flash here. - GSM-Forum

carlos32 · 03-30-2017, 01:08

Card found: S/N : 8CD632DE , v0135
Chinese Miracle II [SPD module] v 1.24

Operation : Format File System / Reset Settings [ v1.24 ]
Settings : SmartFormat is On

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable

==== Wait for phone...

Phone found! [ 30 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Checking Structure ...
Detected eMMC Flash , Structure detect Ok!

eMMC phone detected! Will use 'Safe Format' mode!

Mount : /data
Size : 0x000000013A4F7000
State : 0x0001

Mount : /cache
Size : 0x0000000009600000
State : 0x0001

Prepare Ok! Format Ok!
Don't touch phone, until it fully bootup to "Welcome Screen"!

Android 5.x : Reset FRP Lock
Reset Ok!

Done!

Elapsed: 00:00:27

Reconnect Power/Cable!

Operation : Read FullFlash [ v1.24 ]

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
3. Insert cable

==== Wait for phone...

Phone found! [ 30 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Detected eMMC Flash , Structure detect Ok!

[FW_READER] : Prepare Ok!
- > Wait phone connected ...

Phone found! [ 30 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

- > Wait phone connected ...

Phone found! [ 30 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

Model Name : v2806
Model Brand : WIKO
Model Device: v2806
AndrVersion : 6.0
BaseBand CPU: V2806
Project Ver : MRA58K release-keys
Model Ext : JERRY

[Read Mode] : HSUSB : 0x3000

[FW_READER] : Reading Firmware Now ...

[Read Ok] : u-boot-spl-16k.bin
[Read Ok] : u-boot.bin
[Read Ok] : prodnv.img
[Read Ok] : sc7731C_CP0_modem.bin
[Read Ok] : DSP_DM_Gx.bin
[Read Ok] : nvitem_w.bin
[Read Ok] : sc8830g_modem_CP2_WCN_Trunk_W16.28.5_Release.bin
[Read Ok] : nvitem_wcn.bin
[Read Ok] : logo_480x800.bin
[Read Ok] : fblogo_480x854.bin
[Read Ok] : boot.img
[Read Ok] : system.img
[Read Ok] : sysinfo.img
[Build Ok] : cache.img
[Read Ok] : recovery.img
[Build Ok] : userdata.img

AndroidInfo created
Firmware Size : 2333 MiB
Saved to : C:\Users\carlos32\Desktop\V2806_v2806_6.0_MRA58K_r elease-keys_JERRY\
Done!

Elapsed: 00:26:29

Reconnect Power/Cable!

later will uploud firmware.

carlos32 · 03-30-2017, 01:31

full flash file here: https://ufile.io/5464c

CHANDARAKK · 03-30-2017, 05:20

i need driver please i try many time on win32 bit now work

pranobcox · 03-30-2017, 05:50

sir all spd driver 100%ok win7 32bit win8 32bit

https://drive.google.com/open?id=0B4...UVERUluOEdraWs

without password

only thanks button

BR
Pranobcox

CHANDARAKK · 03-30-2017, 05:56

Quote:

Originally Posted by pranobcox

sir all spd driver 100%ok win7 32bit win8 32bit

https://drive.google.com/open?id=0B4...UVERUluOEdraWs

without password

only thanks button

BR
Pranobcox

i see 3 wich 1 i must download for my Sc7731?

pranobcox · 03-30-2017, 06:03

yes sir sc7731 Spreadtrum Driver SciU2S x86

jamohaki · 03-30-2017, 06:14

Quote:

Originally Posted by carlos32

full flash file here: https://ufile.io/5464c

can you please give another link like mega or 4shared and file is not password protected?

CHANDARAKK · 03-31-2017, 03:31

Quote:

Originally Posted by pranobcox

yes sir sc7731 Spreadtrum Driver SciU2S x86

i did

first run uninstall diver.exe after manual set driver SC7731 as u told in X86 folder it show as my sccreen shot but CM2 not detect yet

carlos32 · 04-01-2017, 18:00

link on mega no pass: https://mega.nz/#!075wUDJb!xiTMECuR0...O9UaiSM0HdcFGc

-=MR_Gsm=- · 09-18-2017, 08:59

wiko jenny spectrum sc7731c__frp done

Android 5.x/6.x : Reset FRP Lock
Reset Ok!

Operation : Format File System / Reset Settings [ v1.27 ]
Settings : SmartFormat is On

1. Remove battery. Insert battery back
2. Press and hold 'VolumeUp' and 'VolumeDown' keys
-> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key
3. Insert cable

==== Wait for phone...

Phone found! [ 36 ]
Port Opened
Sync...
InitBoot Done [ 0x81 ] , Ver : SPRD3
Sync...
Sending FDL
[Info] : If SW freeze here more, than 15 seconds - remove cable
FDL Ready!
Boot Ver : SC7731 Crev eMMC Loader v2.0
Sending FLASH FDL
FLASH FDL Ready!
Boot Ok!

FlashMode Set : Ok!
Checking Structure ...
Detected eMMC Flash , Structure detect Ok!

eMMC phone detected! Will use 'Safe Format' mode!

Mount : /data
Size : 0x000000013A4F7000
State : 0x0001

Mount : /cache
Size : 0x0000000009600000
State : 0x0001

Prepare Ok! Format Ok!
Don't touch phone, until it fully bootup to "Welcome Screen"!

Android 5.x/6.x : Reset FRP Lock
Reset Ok!

Done!

Elapsed: 00:00:28

Reconnect Power/Cable!

kashif_malik · 01-27-2018, 12:01

Both links are not working. Please give working link.

03-30-2017, 01:08	#1 (permalink)
carlos32 No Life Poster Join Date: Nov 2009 Location: portugal Age: 46 Posts: 2,120 Member: 1166261 Status: Offline Sonork: 100.1623881 Thanks Meter: 266	wiko jenny spectrum sc7731c full flash here. Card found: S/N : 8CD632DE , v0135 Chinese Miracle II [SPD module] v 1.24 Operation : Format File System / Reset Settings [ v1.24 ] Settings : SmartFormat is On 1. Remove battery. Insert battery back 2. Press and hold 'VolumeUp' and 'VolumeDown' keys 3. Insert cable ==== Wait for phone... Phone found! [ 30 ] Port Opened Sync... InitBoot Done [ 0x81 ] , Ver : SPRD3 Sync... Sending FDL [Info] : If SW freeze here more, than 15 seconds - remove cable FDL Ready! Boot Ver : SC7731 Crev eMMC Loader v2.0 Sending FLASH FDL FLASH FDL Ready! Boot Ok! FlashMode Set : Ok! Checking Structure ... Detected eMMC Flash , Structure detect Ok! eMMC phone detected! Will use 'Safe Format' mode! Mount : /data Size : 0x000000013A4F7000 State : 0x0001 Mount : /cache Size : 0x0000000009600000 State : 0x0001 Prepare Ok! Format Ok! Don't touch phone, until it fully bootup to "Welcome Screen"! Android 5.x : Reset FRP Lock Reset Ok! Done! Elapsed: 00:00:27 Reconnect Power/Cable! Operation : Read FullFlash [ v1.24 ] 1. Remove battery. Insert battery back 2. Press and hold 'VolumeUp' and 'VolumeDown' keys 3. Insert cable ==== Wait for phone... Phone found! [ 30 ] Port Opened Sync... InitBoot Done [ 0x81 ] , Ver : SPRD3 Sync... Sending FDL [Info] : If SW freeze here more, than 15 seconds - remove cable FDL Ready! Boot Ver : SC7731 Crev eMMC Loader v2.0 Sending FLASH FDL FLASH FDL Ready! Boot Ok! FlashMode Set : Ok! Detected eMMC Flash , Structure detect Ok! [FW_READER] : Prepare Ok! - > Wait phone connected ... Phone found! [ 30 ] Port Opened Sync... InitBoot Done [ 0x81 ] , Ver : SPRD3 Sync... Sending FDL [Info] : If SW freeze here more, than 15 seconds - remove cable FDL Ready! Boot Ver : SC7731 Crev eMMC Loader v2.0 Sending FLASH FDL FLASH FDL Ready! Boot Ok! - > Wait phone connected ... Phone found! [ 30 ] Port Opened Sync... InitBoot Done [ 0x81 ] , Ver : SPRD3 Sync... Sending FDL [Info] : If SW freeze here more, than 15 seconds - remove cable FDL Ready! Boot Ver : SC7731 Crev eMMC Loader v2.0 Sending FLASH FDL FLASH FDL Ready! Boot Ok! Model Name : v2806 Model Brand : WIKO Model Device: v2806 AndrVersion : 6.0 BaseBand CPU: V2806 Project Ver : MRA58K release-keys Model Ext : JERRY [Read Mode] : HSUSB : 0x3000 [FW_READER] : Reading Firmware Now ... [Read Ok] : u-boot-spl-16k.bin [Read Ok] : u-boot.bin [Read Ok] : prodnv.img [Read Ok] : sc7731C_CP0_modem.bin [Read Ok] : DSP_DM_Gx.bin [Read Ok] : nvitem_w.bin [Read Ok] : sc8830g_modem_CP2_WCN_Trunk_W16.28.5_Release.bin [Read Ok] : nvitem_wcn.bin [Read Ok] : logo_480x800.bin [Read Ok] : fblogo_480x854.bin [Read Ok] : boot.img [Read Ok] : system.img [Read Ok] : sysinfo.img [Build Ok] : cache.img [Read Ok] : recovery.img [Build Ok] : userdata.img AndroidInfo created Firmware Size : 2333 MiB Saved to : C:\Users\carlos32\Desktop\V2806_v2806_6.0_MRA58K_r elease-keys_JERRY\ Done! Elapsed: 00:26:29 Reconnect Power/Cable! later will uploud firmware.

03-30-2017, 01:31	#2 (permalink)
carlos32 No Life Poster Join Date: Nov 2009 Location: portugal Age: 46 Posts: 2,120 Member: 1166261 Status: Offline Sonork: 100.1623881 Thanks Meter: 266	full flash file here: https://ufile.io/5464c

03-30-2017, 05:20	#3 (permalink)
CHANDARAKK No Life Poster Join Date: Dec 2008 Posts: 3,483 Member: 930280 Status: Offline Thanks Meter: 1,183	i need driver please i try many time on win32 bit now work

03-30-2017, 05:50	#4 (permalink)
pranobcox Freak Poster Join Date: Mar 2015 Location: Bangladesh Age: 32 Posts: 307 Member: 2364514 Status: Offline Thanks Meter: 390	sir all spd driver 100%ok win7 32bit win8 32bit https://drive.google.com/open?id=0B4...UVERUluOEdraWs without password only thanks button BR Pranobcox

03-30-2017, 06:03	#6 (permalink)
pranobcox Freak Poster Join Date: Mar 2015 Location: Bangladesh Age: 32 Posts: 307 Member: 2364514 Status: Offline Thanks Meter: 390	yes sir sc7731 Spreadtrum Driver SciU2S x86

04-01-2017, 18:00	#9 (permalink)
carlos32 No Life Poster Join Date: Nov 2009 Location: portugal Age: 46 Posts: 2,120 Member: 1166261 Status: Offline Sonork: 100.1623881 Thanks Meter: 266	link on mega no pass: https://mega.nz/#!075wUDJb!xiTMECuR0...O9UaiSM0HdcFGc

09-18-2017, 08:59	#10 (permalink)
-=MR_Gsm=- No Life Poster Join Date: Apr 2008 Location: -=Cellulare Zone Europ-EGYPT=- Posts: 1,219 Member: 762055 Status: Offline Sonork: -=664053=- Thanks Meter: 778	wiko jenny spectrum sc7731c__frp done Android 5.x/6.x : Reset FRP Lock Reset Ok! Operation : Format File System / Reset Settings [ v1.27 ] Settings : SmartFormat is On 1. Remove battery. Insert battery back 2. Press and hold 'VolumeUp' and 'VolumeDown' keys -> Alternative : just ONE 'VolumeUp' or 'VolumeDown' key 3. Insert cable ==== Wait for phone... Phone found! [ 36 ] Port Opened Sync... InitBoot Done [ 0x81 ] , Ver : SPRD3 Sync... Sending FDL [Info] : If SW freeze here more, than 15 seconds - remove cable FDL Ready! Boot Ver : SC7731 Crev eMMC Loader v2.0 Sending FLASH FDL FLASH FDL Ready! Boot Ok! FlashMode Set : Ok! Checking Structure ... Detected eMMC Flash , Structure detect Ok! eMMC phone detected! Will use 'Safe Format' mode! Mount : /data Size : 0x000000013A4F7000 State : 0x0001 Mount : /cache Size : 0x0000000009600000 State : 0x0001 Prepare Ok! Format Ok! Don't touch phone, until it fully bootup to "Welcome Screen"! Android 5.x/6.x : Reset FRP Lock Reset Ok! Done! Elapsed: 00:00:28 Reconnect Power/Cable!

01-27-2018, 12:01	#11 (permalink)
kashif_malik Freak Poster Join Date: Nov 2007 Location: Pakistan Posts: 333 Member: 628369 Status: Offline Sonork: 100.1609794 Thanks Meter: 48	Both links are not working. Please give working link.