C35 "Battery empty, please recharge" error - GSM-Forum

blinet · 04-03-2003, 10:36

PLease HELP

My C35 get error message "Battery empty,please recharge",when power on.After few seconds power off.But charging. I have reflash phone with full flash *flx and try mapping but still the same problem.I have upload blk file with sensor toll,but nothing.
HELP

[email protected]

jerry77 · 04-03-2003, 12:08

You must use "Siemens sensor tool". First read old posts.

Drug_Store · 04-03-2003, 18:01

Or write a clean EEprom...

blinet · 04-05-2003, 08:00

Hallo Drug_Store,

I have write a clean eeprom from your site with Unisiemens tool,but nothing.Mobile can't switch on.Either error message "Battery empty,please recharge" Just death.

I have upload diferent blk file from sensor tool package and also nothing.

Can You post Full Flash and Eeprom,downloaded from one Phone?

Thank

Sorry,bad english

---------------------------------
www.gsm4all.szm.sk
---------------------------------

jerry77 · 04-05-2003, 08:51

Did you try to change battery?

blinet · 04-05-2003, 10:11

Thank for reply

Changing battery not help.
I have new Li-on 3,6V battery and same problem.

---------------------------------
www.gsm4all.szm.sk
---------------------------------

Drug_Store · 04-06-2003, 00:02

Quote:

Originally posted by blinet
Hallo Drug_Store,

I have write a clean eeprom from your site with Unisiemens tool,but nothing.Mobile can't switch on.Either error message "Battery empty,please recharge" Just death.

I have upload diferent blk file from sensor tool package and also nothing.

Can You post Full Flash and Eeprom,downloaded from one Phone?

Thank

Sorry,bad english

---------------------------------
www.gsm4all.szm.sk
---------------------------------

Oh, sorry... I made an update to my site today and forgot to put full flash to C/M 35...
If someone sent me a full flash and eeprom, I´ll put it right away.

Regards

Fre3 Crack3r · 04-06-2003, 10:57

Hello @LL

You need to change the charge IC or the PA

blinet · 04-06-2003, 11:56

Hello freecracker,

Where on board is placed IC and PA. Eventually screen shot.
Thank

---------------------------------
www.gsm4all.szm.sk
---------------------------------

Spas-Mobile · 04-06-2003, 18:35

replace VCO near PA

Drug_Store · 04-07-2003, 03:12

Before enter on hardware labours, try to write CM35repair05.bin with Unisiemens.
http://www.drug-store.itgo.com/SiemensPageCM35.htm

**Victor** · 04-08-2003, 09:30

check soldering of PMB2905 / 06 and rehot it

blinet · 04-12-2003, 13:26

Hi all,

I have upload eeprom and flash from working phone with unisiemens, but same problem. Soldering is O.K.
Now i know, that it is hardware problem.

Can me anybody send a screen shot, where is placed PA

thank

---------------------------------
www.gsm4all.szm.sk
---------------------------------

Drug_Store · 04-12-2003, 16:25

Quote:

Originally posted by blinet
Hi all,

I have upload eeprom and flash from working phone with unisiemens, but same problem. Soldering is O.K.
Now i know, that it is hardware problem.

Can me anybody send a screen shot, where is placed PA

thank

---------------------------------
www.gsm4all.szm.sk
---------------------------------

Remember that after write new eeprom, you need to correct IMEI with Ksie...

Abe · 04-14-2003, 02:34

I repaired a lots of c,m35 with a small trick.Not a very good way,but for me it was ONLY WAY.
In first (left upper) block write value 8000,and phone is repaired,but after that,after 2-3 days of working,the phone will turn off without showing u ina battery bar how much battery is lef.It is full,and after 2-3 days,it just shows BATTERY EMPTY......
So ,you cannot see when battery will be empty,but at least u have a minimum 2 days working phone.
Best regards.

04-03-2003, 10:36	#1 (permalink)
blinet No Life Poster Join Date: Nov 2002 Location: Slovakia Age: 40 Posts: 1,060 Member: 17405 Status: Offline Thanks Meter: 345	C35 "Battery empty, please recharge" error PLease HELP My C35 get error message "Battery empty,please recharge",when power on.After few seconds power off.But charging. I have reflash phone with full flash *flx and try mapping but still the same problem.I have upload blk file with sensor toll,but nothing. HELP [email protected]

04-05-2003, 08:00	#4 (permalink)
blinet No Life Poster Join Date: Nov 2002 Location: Slovakia Age: 40 Posts: 1,060 Member: 17405 Status: Offline Thanks Meter: 345	Hallo Drug_Store, I have write a clean eeprom from your site with Unisiemens tool,but nothing.Mobile can't switch on.Either error message "Battery empty,please recharge" Just death. I have upload diferent blk file from sensor tool package and also nothing. Can You post Full Flash and Eeprom,downloaded from one Phone? Thank Sorry,bad english --------------------------------- www.gsm4all.szm.sk --------------------------------- Last edited by blinet; 04-05-2003 at 10:04.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
S55 "Battery empty! Please recharge problem" ???	byteforce	Siemens Hardware Repair Area	16	12-20-2005 20:10
A52 "Battery empty please recharge"	AVS32	E-Gold Based Phones	3	09-19-2005 15:51
"Battery empty please recharge" on C45	AlphaGSM	Siemens Hardware Repair Area	25	03-02-2005 21:07
My A52 doesn't charge the battery it shows "battery empty, please recharge".	E&D	E-Gold Based Phones	4	12-02-2004 15:11
"Battery empty please recharge" on C45	AlphaGSM	x1x to x45/x50	2	07-30-2003 17:58

04-03-2003, 12:08	#2 (permalink)
jerry77 No Life Poster Join Date: Jan 2002 Posts: 874 Member: 8696 Status: Offline Thanks Meter: 45	You must use "Siemens sensor tool". First read old posts.

04-03-2003, 18:01	#3 (permalink)
Drug_Store No Life Poster Join Date: Sep 2002 Location: Portugal Posts: 8,456 Member: 15312 Status: Offline Sonork: 100.1576041 Thanks Meter: 1,097	Or write a clean EEprom...

04-05-2003, 08:51	#5 (permalink)
jerry77 No Life Poster Join Date: Jan 2002 Posts: 874 Member: 8696 Status: Offline Thanks Meter: 45	Did you try to change battery?

04-05-2003, 10:11	#6 (permalink)
blinet No Life Poster Join Date: Nov 2002 Location: Slovakia Age: 40 Posts: 1,060 Member: 17405 Status: Offline Thanks Meter: 345	Thank for reply Changing battery not help. I have new Li-on 3,6V battery and same problem. --------------------------------- www.gsm4all.szm.sk ---------------------------------

04-06-2003, 10:57	#8 (permalink)
Fre3 Crack3r Banned Join Date: Jan 2002 Location: Morocco , Tetouan Posts: 1,752 Member: 8784 Status: Offline Sonork: 100.63512 Thanks Meter: 31	Hello @LL You need to change the charge IC or the PA

04-06-2003, 11:56	#9 (permalink)
blinet No Life Poster Join Date: Nov 2002 Location: Slovakia Age: 40 Posts: 1,060 Member: 17405 Status: Offline Thanks Meter: 345	Hello freecracker, Where on board is placed IC and PA. Eventually screen shot. Thank --------------------------------- www.gsm4all.szm.sk ---------------------------------

04-06-2003, 18:35	#10 (permalink)
Spas-Mobile Crazy Poster Join Date: Nov 2002 Location: Russia Age: 42 Posts: 50 Member: 17649 Status: Offline Thanks Meter: 0	replace VCO near PA

04-07-2003, 03:12	#11 (permalink)
Drug_Store No Life Poster Join Date: Sep 2002 Location: Portugal Posts: 8,456 Member: 15312 Status: Offline Sonork: 100.1576041 Thanks Meter: 1,097	Before enter on hardware labours, try to write CM35repair05.bin with Unisiemens. http://www.drug-store.itgo.com/SiemensPageCM35.htm

04-08-2003, 09:30	#12 (permalink)
Victor Moderator Join Date: May 1999 Location: Blagoevgrad, Bulgaria Age: 52 Posts: 1,056 Member: 73 Status: Offline Thanks Meter: 537	check soldering of PMB2905 / 06 and rehot it

04-12-2003, 13:26	#13 (permalink)
blinet No Life Poster Join Date: Nov 2002 Location: Slovakia Age: 40 Posts: 1,060 Member: 17405 Status: Offline Thanks Meter: 345	Hi all, I have upload eeprom and flash from working phone with unisiemens, but same problem. Soldering is O.K. Now i know, that it is hardware problem. Can me anybody send a screen shot, where is placed PA thank --------------------------------- www.gsm4all.szm.sk ---------------------------------

04-14-2003, 02:34	#15 (permalink)
Abe No Life Poster Join Date: Apr 2001 Location: Croatia Age: 45 Posts: 1,114 Member: 4185 Status: Offline Thanks Meter: 3	I repaired a lots of c,m35 with a small trick.Not a very good way,but for me it was ONLY WAY. In first (left upper) block write value 8000,and phone is repaired,but after that,after 2-3 days of working,the phone will turn off without showing u ina battery bar how much battery is lef.It is full,and after 2-3 days,it just shows BATTERY EMPTY...... So ,you cannot see when battery will be empty,but at least u have a minimum 2 days working phone. Best regards.