DEad D500 plz help - GSM-Forum

black_chorus · 08-31-2006, 15:49

after bad flash in HWK my d500 is dead it can't conect to pc
plz help
i triead furious box , corona...ns dongle phone can't connect
this is a screan shot

c_ahmad79 · 08-31-2006, 18:10

Quote:

Originally Posted by black_chorus

after bad flash in HWK my d500 is dead it can't conect to pc
plz help
i triead furious box , corona...ns dongle phone can't connect
this is a screan shot

first of all you do this as show in the picture.......... then flash it........ i hope that it will work 100%
try and post result.....luck

plobony · 08-31-2006, 19:08

Short 30 sec or remove the internal battery.
Good luck!

***THE CLASH*** · 08-31-2006, 21:05

before you start stripping , give this a go, i see the phone wont boot . when you see HWK trying to BOOT the mobile plug the cable in then, give it a few attempts keep unplugging and plugging back in,D500 are like this some time..

Rowan · 09-11-2006, 22:32

Hey im having a problem that I got directed to this thread.

My D500 wont even turn on, and when I put a charger in it still wont power up even saying Charging.

What should I do???

g1r9a6d8y · 09-17-2006, 13:38

could someone show more detailed info on how to short these components in the image please, do I short each component individually or short one component to the other, help please

c_ahmad79 · 09-17-2006, 16:51

you just need to short these 2 capasters shown in the picture...................infact there are three but leave the middle one

LBOZ_GSM · 09-26-2006, 17:03

Quote:

Originally Posted by black_chorus

after bad flash in HWK my d500 is dead it can't conect to pc
plz help
i triead furious box , corona...ns dongle phone can't connect
this is a screan shot

try this, first get the software (hwk) ready to flash (the flash files slected ect), but make sure u dont connect the d500 yet, press connect, select d500, then press write flash, then connect the phone to the ufs box without sim card and battery (have the the phone ready to connect to the ufs box) use d500 cable

LBOZ_GSM · 09-26-2006, 17:03

Quote:

Originally Posted by black_chorus

after bad flash in HWK my d500 is dead it can't conect to pc
plz help
i triead furious box , corona...ns dongle phone can't connect
this is a screan shot

try this, first get the software (hwk) ready to flash (theflash files slected ect), but make sure u dont connect the d500 yet, press connect select d500, then press write flash, then connect the phone to the ufs box without sim card and battery

jdhatt · 09-30-2006, 04:43

yup, removed the internal battery and phone powers up again

guty · 10-04-2006, 08:53

Quote:

Originally Posted by c_ahmad79

first of all you do this as show in the picture.......... then flash it........ i hope that it will work 100%
try and post result.....luck

work very good .Thanks

aziman · 10-09-2006, 16:10

Quote:

Originally Posted by lboz

try this, first get the software (hwk) ready to flash (the flash files slected ect), but make sure u dont connect the d500 yet, press connect, select d500, then press write flash, then connect the phone to the ufs box without sim card and battery (have the the phone ready to connect to the ufs box) use d500 cable

Hi just wana say thanks for this post info I had a dead d500 board tried and tried to fash it..NO success , tried this worked first time many thax m8...

AKSON · 11-02-2006, 11:01

MCU File: d500acdl2_hw28.cla CheckSum: 86603F87
TFS File: d500acdl2_hw28.tfs CheckSum: FA7350E6
CFG File: d500acdl2_hw28.cfg 27748 byte(s)
Preloader Ok, 230400 Baud
2nd Boot Failed: not Run

hi
please help i got 2 d500 both got no power when trying to flash i get the results above any solutions ?

AKSON · 11-02-2006, 13:28

hi
when i connect on corona downloader i get the following results any solutions?
** Wait for Connect Request from Mobile...
** (POWER ON the PHONE!)
** Send '0x44' to SWIFT Chip
** Connection granted from SWIFT Chip
** Received 16 bytes from SWIFT chip
** Sending the customer ID and the same 16 bytes to SWIFT chip... OK!
** Try to change Timeout !
** Ok! Timout Changed(1600 mSecond)
** Setting downloading address (SCRAM: 0x0C000000)... OK!

** Downloading the pre-Loader (1780 bytes)... OK!
** Set the start address of pre-Loader (SCRAM:0x0C000000)... OK!

Start Pre-Loader... OK!
Trying to change the baudrate...
Change Baudrate 115200 -> 115200... OK!
Downloading the Boot-Loader (317792 bytes)... checksum mismatched from Pre-Loader (0x2B)

** Close COM port

ocean0 · 02-15-2007, 13:26

Quote:

Originally Posted by lboz

try this, first get the software (hwk) ready to flash (theflash files slected ect), but make sure u dont connect the d500 yet, press connect select d500, then press write flash, then connect the phone to the ufs box without sim card and battery

Just Wanna Say "THX" and to let other know that this treat was working on my set...

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Samsung D500, plz help!	takuma2004	Trident/AGERE Platform	1	06-12-2006 11:49
Dead 3310 Plz help	BeNGo007	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	15	04-01-2005 21:15
Dead t610 plz help	mahussai	Sony Ericsson	1	08-13-2003 09:07
Dead GD67!!! Plz help!!!	Nokia man	Panasonic	0	03-06-2003 23:11
Dead GD35 plz help	patric	Panasonic	1	09-07-2002 12:26

08-31-2006, 19:08	#3 (permalink)
plobony Freak Poster Join Date: Nov 2004 Age: 53 Posts: 239 Member: 91118 Status: Offline Thanks Meter: 25	Short 30 sec or remove the internal battery. Good luck!

08-31-2006, 21:05	#4 (permalink)
*THE CLASH* Super Moderator Join Date: Aug 2005 Location: UK.... Age: 58 Posts: 6,030 Member: 173077 Status: Offline Sonork: 100.1594293 Thanks Meter: 2,795	before you start stripping , give this a go, i see the phone wont boot . when you see HWK trying to BOOT the mobile plug the cable in then, give it a few attempts keep unplugging and plugging back in,D500 are like this some time..

09-11-2006, 22:32	#5 (permalink)
Rowan Junior Member Join Date: Aug 2006 Age: 35 Posts: 24 Member: 334067 Status: Offline Thanks Meter: 0	Hey im having a problem that I got directed to this thread. My D500 wont even turn on, and when I put a charger in it still wont power up even saying Charging. What should I do???

09-17-2006, 13:38	#6 (permalink)
g1r9a6d8y Junior Member Join Date: May 2004 Age: 55 Posts: 5 Member: 64521 Status: Offline Thanks Meter: 0	could someone show more detailed info on how to short these components in the image please, do I short each component individually or short one component to the other, help please

09-17-2006, 16:51	#7 (permalink)
c_ahmad79 No Life Poster Join Date: Jan 2006 Location: inside emmc ufs Age: 19 Posts: 7,188 Member: 221603 Status: Offline Sonork: 100.1581270 Thanks Meter: 6,395	you just need to short these 2 capasters shown in the picture...................infact there are three but leave the middle one

09-30-2006, 04:43	#10 (permalink)
jdhatt Insane Poster Join Date: Nov 2004 Age: 40 Posts: 83 Member: 91936 Status: Offline Thanks Meter: 3	yup, removed the internal battery and phone powers up again

11-02-2006, 11:01	#13 (permalink)
AKSON Freak Poster Join Date: Jul 2006 Location: somewhere in the gsm planet Posts: 95 Member: 315278 Status: Offline Thanks Meter: 18	MCU File: d500acdl2_hw28.cla CheckSum: 86603F87 TFS File: d500acdl2_hw28.tfs CheckSum: FA7350E6 CFG File: d500acdl2_hw28.cfg 27748 byte(s) Preloader Ok, 230400 Baud 2nd Boot Failed: not Run hi please help i got 2 d500 both got no power when trying to flash i get the results above any solutions ?

11-02-2006, 13:28	#14 (permalink)
AKSON Freak Poster Join Date: Jul 2006 Location: somewhere in the gsm planet Posts: 95 Member: 315278 Status: Offline Thanks Meter: 18	hi when i connect on corona downloader i get the following results any solutions? Wait for Connect Request from Mobile... (POWER ON the PHONE!) Send '0x44' to SWIFT Chip Connection granted from SWIFT Chip Received 16 bytes from SWIFT chip Sending the customer ID and the same 16 bytes to SWIFT chip... OK! Try to change Timeout ! Ok! Timout Changed(1600 mSecond) Setting downloading address (SCRAM: 0x0C000000)... OK! Downloading the pre-Loader (1780 bytes)... OK! Set the start address of pre-Loader (SCRAM:0x0C000000)... OK! Start Pre-Loader... OK! Trying to change the baudrate... Change Baudrate 115200 -> 115200... OK! Downloading the Boot-Loader (317792 bytes)... checksum mismatched from Pre-Loader (0x2B) Close COM port