Post here successfully job with Z3X-BOX Samsung (2010-2018)

[fone_gsm]

good job mate

keep it Up

Originally Posted by Thorenzz

i9505 imei repair done!:

1. USB debuging on
2. Root manualy with CF-Auto-root (flashed via ODIN in PDA section)
3. *#7284# - set "UART" to PDA (Default is PDA)
4. *#0808# - set "USB" to AP (Default is AP) ,,,, set "USB settings" to DM+MODEM+ADB (Default is MTP)
5. *#9090# - select "[4]DM over UART(*)" ,,,, phone will reboot.
6. Connect phone with usb (install drivers if needed)
7. Select box comport in z3x
8. Repair button in z3x, fill IMEI.

Phone will check for root, write data, then it will reboot. After reboot connect phone with c3300k microUART rj45 cable (if its stuck on "Checking phone at COMxx..." then quickly *#9090# - "DM over UART", u should have enough time to reboot phone while z3x still searching on comport). z3x will write IMEI and reboot phone. All done!. Phone may search for network little bit longer but it will sign into network after while (max 2mins).

Selected model: I9505
Selected port: COM18 Z3X BOX Serial Port
Selected port speed: 115200
Searching ADB device... OK
Reading phone info...
Model: GT-I9505
Android version: 4.2.2
Product code: Not Active
Phone version: I9505XXUAMDM
PDA version: I9505XXUAMDM
CSC version: I9505OXXAMDB
IMEI: Unknown
Checking Super user right... true
Writing data to phone... OK
Rebooting phone... OK
Now connect phone to UART cable
Checking phone at COM18 OK
Reading phone info...
Model: GT-I9505
Country code: BTU
Cal date: -
Factory SW: I9505XXUAMDM
Unique number: CAF001707121230
Memory phone: -
Bypass MSL... OK
Repairing IMEI... OK
Rebooting... OK
Repair done
Done with Samsung Tool v.14.9

[Abdullah Shafiq]

Hi, trying to repair IMEI of galaxy advance i9070 which is when checked gives just (IMEI). Tried to repair with z3x but not repaired even it is showing repair done.
Here is the log:

Selected model: I9070
Selected port: COM7 Z3X BOX Serial Port
Selected port speed: 115200
Reading phone info...
Model: GT-I9070
Android version: 2.3.6
Product code: Unknown
Phone version: Unknown
PDA version: I9070JPLD3
CSC version: I9070OJPLD3
IMEI: Unknown
Checking Super user right... true
Reading data from phone... OK
Now connect phone to UART cable
Checking phone at COM7 OK
Bypass MSL... OK
Repairing IMEI... OK
Repair done
Done with Samsung Tool v.14.9

Please I need urgent help.

Regards.

[Thorenzz]

Originally Posted by Abdullah Shafiq

Hi, trying to repair IMEI of galaxy advance i9070 which is when checked gives just (IMEI). Tried to repair with z3x but not repaired even it is showing repair done.
Here is the log:

Selected model: I9070
Selected port: COM7 Z3X BOX Serial Port
Selected port speed: 115200
Reading phone info...
Model: GT-I9070
Android version: 2.3.6
Product code: Unknown
Phone version: Unknown
PDA version: I9070JPLD3
CSC version: I9070OJPLD3
IMEI: Unknown
Checking Super user right... true
Reading data from phone... OK
Now connect phone to UART cable
Checking phone at COM7 OK
Bypass MSL... OK
Repairing IMEI... OK
Repair done
Done with Samsung Tool v.14.9

Please I need urgent help.

Regards.

Please post this in z3x section not in this section. U will get answers more likely in general z3x section. I personally dont know the answer coz I never came across I9070.

[Thorenzz]

Originally Posted by Thorenzz

i9505 imei repair done!:

1. USB debuging on
2. Root manualy with CF-Auto-root (flashed via ODIN in PDA section)
3. *#7284# - set "UART" to PDA (Default is PDA)
4. *#0808# - set "USB" to AP (Default is AP) ,,,, set "USB settings" to DM+MODEM+ADB (Default is MTP)
5. *#9090# - select "[4]DM over UART(*)" ,,,, phone will reboot.
6. Connect phone with usb (install drivers if needed)
7. Select box comport in z3x
8. Repair button in z3x, fill IMEI.

Phone will check for root, write data, then it will reboot. After reboot connect phone with c3300k microUART rj45 cable (if its stuck on "Checking phone at COMxx..." then quickly *#9090# - "DM over UART", u should have enough time to reboot phone while z3x still searching on comport). z3x will write IMEI and reboot phone. All done!. Phone may search for network little bit longer but it will sign into network after while (max 2mins).

Selected model: I9505
Selected port: COM18 Z3X BOX Serial Port
Selected port speed: 115200
Searching ADB device... OK
Reading phone info...
Model: GT-I9505
Android version: 4.2.2
Product code: Not Active
Phone version: I9505XXUAMDM
PDA version: I9505XXUAMDM
CSC version: I9505OXXAMDB
IMEI: Unknown
Checking Super user right... true
Writing data to phone... OK
Rebooting phone... OK
Now connect phone to UART cable
Checking phone at COM18 OK
Reading phone info...
Model: GT-I9505
Country code: BTU
Cal date: -
Factory SW: I9505XXUAMDM
Unique number: CAF001707121230
Memory phone: -
Bypass MSL... OK
Repairing IMEI... OK
Rebooting... OK
Repair done
Done with Samsung Tool v.14.9

UPDATE: I was experiencing some troubles to get 3G working properly. However, after flash of firmware and wipe data and cache afterwards everything works as it should, expect that phone is searching for network one minute, max two (WEIRD).

[Abdullah Shafiq]

I already have asked two or three times in forum but with no response.
Where is this z3x section?
Can u post the link plz..

Its urgent

[Abdullah Shafiq]

Is this the fault of UART cable..??bcz I am not confirmed wheather it is UART or not..

[anrmobile]

Selected com port: COM6
Selected speed port: 921600
Phone must be OFF
Press * and connect phone by USB cable
Connecting to Device... OK
Sending preloader ... OK
Sending loader ... OK
Erasing ... OK
Sending...E2230XXKL1_bin.fls (../HW/XMM6180_EHS2AGR_CATFISH_NARI_1.0_CUST/BSY_DEBUG/catfish.fls)
Erasing ... OK
Writing ... OK
Sending...E2230XXKL1_cds.fls (../HW/XMM6180_EHS2AGR_CATFISH_NARI_1.0_CUST/CDS_DEBUG/catfish.fls)
Erasing ... OK
Writing ... OK
Sending...E2230OXAKB7_CSC.dffs (temp_GT-E2230_OXA.dffs)
Erasing ... OK
Writing ... OK
Flash FLS - ok
Elapsed time: 238 second, sw ver: 3.5.0040

[asif ali]

GT-I9300 unlock done

[Rin2]

E1207t duos imei repair success..

Selected model: E1202
Selected com port: COM7
Selected speed port: 921600
Please, connect phone and press power button 3 seconds
Phone Detected
Sending loader1... OK
Flash ID: F896
Sending loader2... OK
Please wait for patching firmware...
Patch block
Please, connect phone and press power button 3 seconds
Phone Detected
Use automatic parameters
Phone in TAT MODE
Phone master IMEI: 00000000000000
Phone slave IMEI: 00000000000000
Phone SW: E1207TDDLL1
Phone CSC: E1207TODDLJ2
Phone BT ADDR: 0000-00-000000
Phone SN: S200003804
Deactivated MSL - TRUE
Write master imei - ok
Write slave imei - ok
Repair - ok
Elapsed time: 60 second, sw ver: 3.5.0040

[anrmobile]

Selected model: T659
Selected port: COM7 Z3X BOX Serial Port
Selected port speed: 115200
Reading phone info... OK
Model: SGH-T659
Country code: ¹Ì±¹/TMB
Cal date: 2009-07-28
Factory SW: UVIG9
Unique number: 72990000609245
Memory phone: K5R2G1GACC(T659)S
Phone S/N: R7WSB04065
Reading IMEI... OK
IMEI: 352446031173148
Build: M6246A-KPVZL-1.2.0035
Reading phone version... OK
Phone version: T659UVIG9
Searching sysinfo... OK
Reading sysinfo... OK
Type *#7465625# and press OK
Then repeat procedure
Done with Samsung Tool v.14.9

Selected model: T659
Selected port: COM7 Z3X BOX Serial Port
Selected port speed: 115200
Reading phone info... OK
Model: SGH-T659
Country code: ¹Ì±¹/TMB
Cal date: 2009-07-28
Factory SW: UVIG9
Unique number: 72990000609245
Memory phone: K5R2G1GACC(T659)S
Phone S/N: R7WSB04065
Reading IMEI... OK
IMEI: 352446031173148
Build: M6246A-KPVZL-1.2.0035
Reading phone version... OK
Phone version: T659UVIG9
Searching sysinfo... OK
Reading sysinfo... OK
Please wait, calculating codes... OK (time - 00:00:45)
Freeze code: 25296146
NET lock: #7465625*638*59646240#
Sub lock: #7465625*782*00000000#
SP lock: #7465625*77*00000000#
CP lock: #7465625*27*00000000#
For check lock status: *#7465625#
Done with Samsung Tool v.14.9
Done with Samsung Tool v.14.9

[chipscell25]

unlock samsung t669 done



Uploaded with ImageShack.us

[Prem_India]

Samsung C3262 Unlock Done


B.R.,
Prem_India

[dimityr.milev]

Selected model: S5369
Selected port: COM3 Z3X BOX Serial Port
Selected port speed: 115200
Reading phone info...
Model: GT-S5369
Android version: 2.3.6
Product code: Unknown
Phone version: S5369BULA1
PDA version: S5369BULA1
CSC version: S5369VDRLA1
IMEI: 358858042186030
Checking Super user right... false
Rooting phone, please wait... OK
Checking Super user right... true
Reading data from phone... OK
Unlocking... OK
Rebooting phone... OK
Unlock done
Done with Samsung Tool v.14.8
Done with Samsung Tool v.14.8

[Murat Bekar]

N7100 one click imei repair done

Selected model: N7100
Selected port: COM3 Z3X BOX Serial Port
Selected port speed: 115200
Searching ADB device... OK
Reading phone info...
Model: GT-N7100
Android version: 4.1.2
Product code: GT-N7100TADXEF
Phone version: N7100XXDLK7
PDA version: N7100XXDMB6
CSC version: N7100OXADMB1
IMEI: Unknown
Checking Super user right... false
Rooting phone, please wait... OK
Checking Super user right... true
Reading data from phone... OK
Repairing network settings... OK
Writing data to phone... OK
Rebooting phone... OK
Now connect phone to UART cable
Checking phone at COM3 OK
Reading phone info...
Model: GT-N7100
Country code: XEF
Factory SW: N7100XXDMB6
Unique number: CVTF7EFB5549CCF
Memory phone: VTU00M
Bypass MSL... OK
Repairing IMEI... OK
Repair done
Rebooting... OK
Done with Samsung Tool v.14.9

thanks to Z3X-Team

Best Regards

[sajib_ngage]

M919 S4 unlock success............................

Selected model: M919
Selected port: COM12 Z3X BOX Serial Port
Selected port speed: 115200
Reading phone info...
Build: M9615A-CEFWTAZM-4.0.17062
Done with Samsung Tool v.14.9

Selected model: M919
Selected port: COM12 Z3X BOX Serial Port
Selected port speed: 115200
Reading phone info...
Build: M9615A-CEFWTAZM-4.0.17062
Reading security... OK
Searching server... OK
NET lock: #7465625*638*14853735#
Sub lock: #7465625*782*00000000#
SP lock: #7465625*77*00000000#
CP lock: #7465625*27*00000000#
For check lock status: *#7465625#
Done with Samsung Tool v.14.9