V3re dead in the unlock!! ! - GSM-Forum

michel.tissier · 09-15-2008, 15:59

Hi! I have a v3re that in the middle of the process for unlock (with mss)

give me a error and after that the phone is in blank mode.

now i try to full flash but allways say " Unsupported bootloader version "

but before the unlock the bootloader was correct . The next that i try

is with smart clip but the problem is the same "Bootloader 0x400 is not

supported for this model V3re ". The tp is fine , i don't cut any track or

any component of the phone. I have other v3re that i unlock without

problem ...

Please help me

THANKS IN ADVANCE

michel.tissier · 09-15-2008, 16:15

I need to know why this problem happens !!??
already it has happened to me before,
and I do not want that it returns to happen to me

thanks..

anxindn · 09-20-2008, 03:22

U can reflash with MSS,,not full!!!! goodluck!

~AKSingh~ · 09-20-2008, 05:28

Quote:

Originally Posted by michel.tissier

Hi! I have a v3re that in the middle of the process for unlock (with mss)

give me a error and after that the phone is in blank mode.

now i try to full flash but allways say " Unsupported bootloader version "

but before the unlock the bootloader was correct . The next that i try

is with smart clip but the problem is the same "Bootloader 0x400 is not

supported for this model V3re ". The tp is fine , i don't cut any track or

any component of the phone. I have other v3re that i unlock without

problem ...

Please help me

THANKS IN ADVANCE

check if u have new version of special argon test point with tp1 and tp2
i have successfully unlocked so many sets with same bootloaders
repeat the process please

wbr

michel.tissier · 09-22-2008, 16:06

Quote:

Originally Posted by anxindn

U can reflash with MSS,,not full!!!! goodluck!

NO! i can't reflash the phone i can't do anything , and i can't pass a boot either
thanks anyway !

michel.tissier · 09-22-2008, 16:08

Quote:

Originally Posted by ~AKSingh~

check if u have new version of special argon test point with tp1 and tp2
i have successfully unlocked so many sets with same bootloaders
repeat the process please

wbr

sorry but i don't understand what you try to say to me

. The phone is in blank mode and i need to revive it

anxindn · 09-23-2008, 04:03

trust me!! you flash with monterpark!!!, sorry my english! Or you can testpoint with smarkclip then write fullflash with smarkclip,goodluck!!!

michel.tissier · 09-23-2008, 13:59

Quote:

Originally Posted by anxindn

trust me!! you flash with monterpark!!!, sorry my english! Or you can testpoint with smarkclip then write fullflash with smarkclip,goodluck!!!

noooooooooooooooooooo man, if you don't know , don't tell me what to do ! did this happend to you some time???? I already told you that always give me a error , when i put a full flash , when i reflash.. always !
I think that there is no solution for this problem

thanks anyway

..::Sunil::.. · 09-02-2009, 08:34

I have same problem here....I think bootloader is erased....any body have boot loader file 0cc1 ....or anyother idea to revive...thx ..

B.r.

..::Sunil::.. · 09-02-2009, 08:35

sorry for double post...any mod plz delete it

Gabiunlock · 09-03-2009, 13:39

Quote:

Originally Posted by michel.tissier

Hi! I have a v3re that in the middle of the process for unlock (with mss)

give me a error and after that the phone is in blank mode.

now i try to full flash but allways say " Unsupported bootloader version "

but before the unlock the bootloader was correct . The next that i try

is with smart clip but the problem is the same "Bootloader 0x400 is not

supported for this model V3re ". The tp is fine , i don't cut any track or

any component of the phone. I have other v3re that i unlock without

problem ...

Please help me

THANKS IN ADVANCE

Quote:

Originally Posted by ~AKSingh~

check if u have new version of special argon test point with tp1 and tp2
i have successfully unlocked so many sets with same bootloaders
repeat the process please

wbr

Quote:

Originally Posted by anxindn

trust me!! you flash with monterpark!!!, sorry my english! Or you can testpoint with smarkclip then write fullflash with smarkclip,goodluck!!!

Quote:

Originally Posted by ..::Sunil::..

I have same problem here....I think bootloader is erased....any body have boot loader file 0cc1 ....or anyother idea to revive...thx ..

B.r.

if u have v3re u need downgrade boot by tp at 0.00 for unlock or repair PDS, if u after operation you see boot 04.00 at moment not solution any tool. repeat NO SOLUTION by software.

BR

Gabiunlock

siddgoin · 10-07-2009, 08:11

Quote:

Originally Posted by Gabiunlock

if u have v3re u need downgrade boot by tp at 0.00 for unlock or repair PDS, if u after operation you see boot 04.00 at moment not solution any tool. repeat NO SOLUTION by software.

BR

Gabiunlock

if u have v3re u need downgrade boot by tp at 0.00 sir what u mean by 0.00 please if u give advice then write or specify it clearly dont make people confused with magic words ..... is it eny solution for my set getting back in normal mode its v3re R3442A_G_0E.43.25R i am nota able to flash it its in blank mode if u can help me please help me

Gabiunlock · 10-08-2009, 16:16

sorry..........

what need?

Rabatu · 10-08-2009, 16:34

so now it's a bootloader problem and flashing or unlocking only possible after repairing bootloader, in which will also require tp procedure or otherwise this case had no solution yet

ismabdi · 12-13-2009, 09:33

[8:36:56 PM 1.28] MSS Service Software for MSS Box II - version 1.28 - www.mssbox.com
[8:36:56 PM 1.28] Session started 12/12/2009
[8:36:56 PM 1.28] Box UID:10007440 connected
[8:37:16 PM 1.28] Phone connected in normal mode
[8:37:16 PM 1.28] IMEI: 35247602775000, R3442A_G_0E.43.04R_A, GSTRAZR06MCL01NA10D..., Boot:Unknown, LP:0B57, Motorola Phone (V3re), Locked 302 - 037
[8:37:36 PM 1.28] [8:37:36 PM] Unlocking started - MSS Service Software ver. 1.28 - R3442A_G_0E.43.04R_A, Boot:Unknown
[8:37:36 PM 1.28] Switching phone to flash mode...
[8:37:43 PM 1.28] Reading data...
[8:37:53 PM 1.28] Phone is powered off
[8:37:53 PM 1.28] If phone will not power up within 10 seconds, please, reconnect phone cable (and battery if used). If phone will not power up after this, turn on phone in flash mode manually (*, #, PWR)
[8:38:41 PM 1.28] Phone found. Continue...
[8:38:41 PM 1.28] Switching phone to flash mode...
[8:38:51 PM 1.28] Loading RAM Downloader...
[8:38:54 PM 1.28] Erasing flash memory...
[8:38:55 PM 1.28] Flashing started
[8:38:58 PM 1.28] Phone is powered off
[8:39:00 PM 1.28] Please disconnect phone and connect battery hook (adapter version 3) and not powered (original) USB cable
Phone found. Continue...
[8:45:01 PM 1.28] Please connect special testpoint
[8:45:54 PM 1.28] Please hold testpoint connected...
[8:45:59 PM 1.28] Please disconnect special testpoint
[8:46:01 PM 1.28] Flash type: Tyax 16 bit, size - 32 Mb
[8:46:01 PM 1.28] Backing up PDS area...
[8:46:05 PM 1.28] Unlocking started...
[8:46:13 PM 1.28] Complete
[8:46:13 PM 1.28] [8:46:13 PM] Ok
[8:46:13 PM 1.28] C:\Program Files\MSS_II_Box\MSS\Backups\Auto\PDS_IMEI35247602 775000_SN891B160303102460_12.12.09_20.46.mbc

now set is dead no boot no balnk mode 1.28 its have bug

09-15-2008, 15:59	#1 (permalink)
michel.tissier No Life Poster Join Date: Mar 2008 Location: The Twilight Zone Posts: 1,280 Member: 736073 Status: Offline Thanks Meter: 81	V3re dead in the unlock!! ! Hi! I have a v3re that in the middle of the process for unlock (with mss) give me a error and after that the phone is in blank mode. now i try to full flash but allways say " Unsupported bootloader version " but before the unlock the bootloader was correct . The next that i try is with smart clip but the problem is the same "Bootloader 0x400 is not supported for this model V3re ". The tp is fine , i don't cut any track or any component of the phone. I have other v3re that i unlock without problem ... Please help me THANKS IN ADVANCE

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
v3re stuck in the bootloader	k-cell	Smart-Clip	8	09-16-2010 10:27
BB 8320 dead in the upgrade for flash	subzeven	BlackBerry (RIM)	1	07-22-2009 08:28
v3re dead in the unlock!!	michel.tissier	Motorola P2k	6	09-20-2008 06:05
V3re dead in the unlock!!	michel.tissier	Smart-Clip	4	09-16-2008 13:31
CU500 DEAD in the middle of Flash-unlocking (Cant enter Emergency Mode)	dannyogolo	FuriousGold	7	09-28-2007 22:34

09-15-2008, 16:15	#2 (permalink)
michel.tissier No Life Poster Join Date: Mar 2008 Location: The Twilight Zone Posts: 1,280 Member: 736073 Status: Offline Thanks Meter: 81	I need to know why this problem happens !!?? already it has happened to me before, and I do not want that it returns to happen to me thanks..

09-20-2008, 03:22	#3 (permalink)
anxindn Junior Member Join Date: Jun 2005 Age: 40 Posts: 15 Member: 149850 Status: Offline Thanks Meter: 0	U can reflash with MSS,,not full!!!! goodluck!

09-23-2008, 04:03	#7 (permalink)
anxindn Junior Member Join Date: Jun 2005 Age: 40 Posts: 15 Member: 149850 Status: Offline Thanks Meter: 0	trust me!! you flash with monterpark!!!, sorry my english! Or you can testpoint with smarkclip then write fullflash with smarkclip,goodluck!!!

09-02-2009, 08:34	#9 (permalink)
..::Sunil::.. Banned Join Date: Jan 2007 Location: India Age: 34 Posts: 2,705 Member: 432364 Status: Offline Thanks Meter: 270	I have same problem here....I think bootloader is erased....any body have boot loader file 0cc1 ....or anyother idea to revive...thx .. B.r.

09-02-2009, 08:35	#10 (permalink)
..::Sunil::.. Banned Join Date: Jan 2007 Location: India Age: 34 Posts: 2,705 Member: 432364 Status: Offline Thanks Meter: 270	sorry for double post...any mod plz delete it

10-08-2009, 16:16	#13 (permalink)
Gabiunlock No Life Poster Join Date: Feb 2008 Location: Misiones Posts: 1,197 Member: 710759 Status: Offline Sonork: No Thanks Meter: 329	sorry.......... what need?

10-08-2009, 16:34	#14 (permalink)
Rabatu No Life Poster Join Date: Apr 2009 Posts: 602 Member: 1009679 Status: Offline Thanks Meter: 166	so now it's a bootloader problem and flashing or unlocking only possible after repairing bootloader, in which will also require tp procedure or otherwise this case had no solution yet