samsung coby f339 boot repair - GSM-Forum

accurate · 12-04-2010, 16:17

hi i have sam f339 dead during flash before flash problem only user code during flash soft hang i remove battery after that set is not on even emergency mode, can i repair boot ?

gsmsikar · 12-05-2010, 20:30

can u give the CPU and Flash details of this set and also a good quality image of this phone ..?

Selim_yousuf · 04-15-2012, 17:18

Quote:

Originally Posted by gsmsikar

can u give the CPU and Flash details of this set and also a good quality image of this phone ..?

cpu---QSC6075 any solution for go to eng\download mode ???

andyvikas · 04-18-2012, 15:21

Its Standard 9 Pin Connection Just Below Sim Connector..

1 VCC, 2 TMS, 3 RTCK, 4 TRST, 5 TDI, 6 TCK, 7 TDO, 8 NRST, 9 GND

Code:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.32, JTAG Manager Version: 1.42
Selected Resurrector: [Samsung B209 V1.00]

Connecting to the dead body...OK
Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK

Detected dead body ID: 0x100FA0E1

Code:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.32, JTAG Manager Version: 1.42
Selected Resurrector: [Samsung B209 V1.00]

Connecting to the target...OK
Set I/O Voltage reads as 2.60V, TCK Frequency is RTCK

Following devices are found on the JTAG chain:
  Device on TAP #0: ID = 0x100FA0E1, IR Length = 0x04 bits
Total IR length: 0x0004 bits

Code:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.32, JTAG Manager Version: 1.42
Selected Resurrector: [Samsung B209 V1.00]

Halting target...OK
STATUS: Target is halted.

  R0 = 0x00240201    R6 = 0x0000000C    R12 = 0x00000001
  R1 = 0xFBF06040    R7 = 0x0486C54C    R13 = 0x008D6920
  R2 = 0xFBF06000    R8 = 0x00000000    R14 = 0x00000015
  R3 = 0x0001B000    R9 = 0x00000000    R15 = 0x001FE50C
  R4 = 0x0000FC4C   R10 = 0x00000000   CPSR = 0x400000B0
  R5 = 0x00000001   R11 = 0x00000000

Code:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.32, JTAG Manager Version: 1.42
Selected Resurrector: [QSC6XXX 32/08 M01D1 NAND V1.00]

Connecting to the dead body...OK
Detected dead body ID: 0x100FA0E1 - CORRECT!
Set I/O Voltage reads as 1.95V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]
Settings Code: 0x25010000000000000000000008000000

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected a Not Initialized FLASH1 Chip, ID: 0xAAAA/0xAAAA (256MB)

ERROR: Selected FLASH1 Chip was not Recognized by the DCC Loader. Terminating.

Processor:
QSC6075

Memory IC:
SEC 031BL60
K5W2GHACF

Which Dll to select for reading full dump??

PS: Set is Blinking on Samsung Logo, Can be flashed in emergency mode too, but still stucked at samsung logo..

Thanks

Anil Sharma 123 · 10-07-2012, 08:39

Quote:

Originally Posted by andyvikas

Its Standard 9 Pin Connection Just Below Sim Connector..

1 VCC, 2 TMS, 3 RTCK, 4 TRST, 5 TDI, 6 TCK, 7 TDO, 8 NRST, 9 GND

Code:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.32, JTAG Manager Version: 1.42
Selected Resurrector: [Samsung B209 V1.00]

Connecting to the dead body...OK
Set I/O Voltage reads as 2.61V, TCK Frequency is RTCK

Detected dead body ID: 0x100FA0E1

Code:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.32, JTAG Manager Version: 1.42
Selected Resurrector: [Samsung B209 V1.00]

Connecting to the target...OK
Set I/O Voltage reads as 2.60V, TCK Frequency is RTCK

Following devices are found on the JTAG chain:
  Device on TAP #0: ID = 0x100FA0E1, IR Length = 0x04 bits
Total IR length: 0x0004 bits

Code:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.32, JTAG Manager Version: 1.42
Selected Resurrector: [Samsung B209 V1.00]

Halting target...OK
STATUS: Target is halted.

  R0 = 0x00240201    R6 = 0x0000000C    R12 = 0x00000001
  R1 = 0xFBF06040    R7 = 0x0486C54C    R13 = 0x008D6920
  R2 = 0xFBF06000    R8 = 0x00000000    R14 = 0x00000015
  R3 = 0x0001B000    R9 = 0x00000000    R15 = 0x001FE50C
  R4 = 0x0000FC4C   R10 = 0x00000000   CPSR = 0x400000B0
  R5 = 0x00000001   R11 = 0x00000000

Code:

Open serial port...OK
Connecting to the RIFF Box...OK
Firmware Version: 1.32, JTAG Manager Version: 1.42
Selected Resurrector: [QSC6XXX 32/08 M01D1 NAND V1.00]

Connecting to the dead body...OK
Detected dead body ID: 0x100FA0E1 - CORRECT!
Set I/O Voltage reads as 1.95V, TCK Frequency is RTCK
Adaptive Clocking RTCK Sampling is: [Sample at MAX]
Settings Code: 0x25010000000000000000000008000000

Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK

Detected a Not Initialized FLASH1 Chip, ID: 0xAAAA/0xAAAA (256MB)

ERROR: Selected FLASH1 Chip was not Recognized by the DCC Loader. Terminating.

Processor:
QSC6075

Memory IC:
SEC 031BL60
K5W2GHACF

Which Dll to select for reading full dump??

PS: Set is Blinking on Samsung Logo, Can be flashed in emergency mode too, but still stucked at samsung logo..

Thanks

Here Is Tested By Me Dll............

Select Qualcomm QSC6XXX L36 D08 One Nand And Do Your Job

BR,

ANIL SHARMA

imrankhan0143 · 12-15-2012, 11:14

Quote:

Originally Posted by Anil Sharma 123

Here Is Tested By Me Dll............

Select Qualcomm QSC6XXX L36 D08 One Nand And Do Your Job

BR,

ANIL SHARMA

sir
i need dump samsung
f339

Gsmbizz · 11-18-2013, 11:44

Dump plssssssssssssssssssssssssss

12-04-2010, 16:17	#1 (permalink)
accurate Banned Join Date: Mar 2007 Location: INDIA Age: 43 Posts: 298 Member: 470867 Status: Offline Thanks Meter: 32	samsung coby f339 boot repair hi i have sam f339 dead during flash before flash problem only user code during flash soft hang i remove battery after that set is not on even emergency mode, can i repair boot ?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Nokia "Contact Service" Repairer	Dirk	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	5	10-04-2011 05:45
Contact Service Repairer 1.2 by Bartek	Allen	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	4	02-23-2011 09:00
F_loaders.bin and Boot.bin .. .	micklong	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	1	01-29-2001 14:49
Phone not respond! (Load boot data) Need a help !	SashaM	Nokia Legacy Phones ( DCT-1 ,2 ,3 ,L )	2	01-23-2001 02:10
New!! Nokia Flash Checksum And Contact Service Repair	HookerGsM	Main Sales Section	0	01-02-2001 10:12

12-05-2010, 20:30	#2 (permalink)
gsmsikar No Life Poster Join Date: May 2003 Posts: 5,667 Member: 28004 Status: Offline Sonork: 100.1601142 Thanks Meter: 770	can u give the CPU and Flash details of this set and also a good quality image of this phone ..?

11-18-2013, 11:44	#7 (permalink)
Gsmbizz No Life Poster Join Date: Apr 2008 Age: 28 Posts: 1,700 Member: 745672 Status: Offline Thanks Meter: 555	Dump plssssssssssssssssssssssssss